Summary of Contents for SWorkz S35-GT2.2FTE Series
Page 2
The S35-GT2 has a weight-optimized, hard anodized base chassis plate made of high-strength T7075 aluminum. The HET differentials developed by SWORKz are also included with 13T pinion and 45T crowns in the kit. The wishbone brackets, included with square inserts, allow the axle geometry of your SWORKz S35- GT2 to be adapted to any track layout.
I N D E X Instruction Warranty Index Required equipment for operation Operation guide Assembly steps 7-36 Blank set-up sheet 37-38 Race Report S35-GT2.2 FTE Key No. List 40-41 S35-GT2.2 FTE Spare Part List 41-42 S35-GT2.2 FTE Option Part List End cover This radio controlled racing car is not a toy! This high-performance R/C model is recommended for ages 14 and older.
Compound S a fe t y Pre c au t io n s The SWORKz S35-GT2.2 FTE is a high performance radio control model which needs to be operated with caution and common sense. The S35-GT2.2 FTE Pro Kit is not intended for children under the age of 14 without adult supervision.
Page 7
610023 328001 101004 101004 101004 Washer 3.5X10X0.2mm 328001 101004 338025 328001 101004 Fill the differentials with oil up to 80% above the satellite gears. Put the SWORKz Diff. Oil 500000cps for the front Diff. and 50000cps for the rear Diff.
Page 12
104004 M3x3mm Set Screw 116009 Flange Ball Bearing 5x8x2.5mm 104004 116009 339008 339023 224007L3.5-6 OPTION: SW-119001-2.3 S35-GT2.2 FTE Front Sway Bar 2.3mm SW-119001-2.4 S35-GT2.2 FTE Front Sway Bar 2.4mm SW-119001-2.6 S35-GT2.2 FTE Front Sway Bar 2.6mm 119001-2.5 SW-119001-2.8 S35-GT2.2 FTE Front Sway Bar 2.8mm SW-119001-3.0 S35-GT2.2 FTE Front Sway Bar 3.0mm 104004 Note:...
Page 13
S35-3 Front Upper Arm Adjust Insert (1.1mm) 2503260-4 228009 S35-3 Front Upper Arm Adjust Insert (2.0mm) 330664 2501667-6 339032 SWORKz S35-GT2.2 FTE Series Shock End Extension Holder Pin-Screws Left 330134 103004 M2.5mm Nut Lock 339001 106003 M3x16mm Hex Soket OH/TP Screw 106022...
108003 108003 M3x10mm FH/ST HEX Screw 108003 108010 M4x10mm FH/ST HEX Screw Front 108010 Top View Rear 106002 106002 349011 M3x10mm Hex Socket OH/TP Screw Right 330115 Steering Knuckle Pivot Ball Turnbuckle 330115 330116 2503260-04 330118A Left 2503264A 330115 330118A 330116 Screw and adjust 330118A Knuckle 2503260-04...
Page 17
Right 104010 M5x4mm Set Screw (Flat Bottom) 330124 Pin M3.0x16.8mm 116006C 116006C Ball Bearing 8x16x5mm (Red Rubber Case) 218007D 101018 Left 101018 116006C 338080 SHIM 13x16x0.2mm Note: 101018SHIM 13x16x0.2mm Please use 13x16x0.2mm shims to adjust the 104010 gap between the wheel hub and wheel knuckles. Standard suggestion is 1pc shim on the outside 330124 between 8x16x5mm ball bearing and knuckle.
Page 25
106002 M3x10mm Hex Soket OH/TP Screw 106002 106002 106008 106008 106003 106003 106008 M3x12mm Hex Socket OH/TP Screw Servos are not 106003 included in the kit. M3x16mm Hex Socket OH/TP Screw 2503262 2503262 2503262...
Page 26
106002 Receiver and switch are The switch is not not included in the kit. included in the kit. 103001 M3 Nut Lock 106002 M3x10mm Hex Socket OH/TP Screw Laps transponder is not included in the kit. 103001 108006 108006 108006 OPTION: M3x8mm FH/ST HEX Screw SWC-210088 S35 Nitro Series Pro-...
Page 27
Li-ion Size:18500 104004 M3x3mm Set Screw 106001 106001 Battery is not 106001 included in the kit. 2503262 M3x8mm Hex Socket OH/TP Screw 106001 200193 Li-ion Size:18650 104004 OPTION: SWC-210088 S35 Nitro Series Pro- composite Carbon One Unit Radio Tray 108006 M3x8mm FH/ST HEX Screw 108006 108006...
Page 29
When the volume 106020 106002 of fuel tank system 108006 2502040-6 is over 125cc, M3x8mm FH/ST HEX Screw using the part 2502040-02 210048-D90 210048-D90 can be reduced 2cc for your fuel tank. 106020 M2.5x5mm Hex Socket OH/TP Screw 106020 106002 M3x10mm Hex Socket OH/TP Screw 108006 108006...
Race time / Lap: SET-UP SHEET Best lap: Rear Suspension SWC-218007A S35 Series Evolution-CVA Drive Shaft Set 92.5mm SWC-218007D S35 Series Advance-CVD Drive Shaft Set 92.5mm Body: SW-210046 S350 Series LDS Universal Cross Drive Shaft Set 92.5mm Wing: Camber angle Lay Down Body Shell Post Non-use Wheel Hub Note:...
Page 40
228016-1.3-8 SWORKz 1/8 BBS Precision Plastic Shock Piston(1.3X8Holes) 2 SW-228016-1.3-8 339013 S35-GT2.2 FTE Series Aluminum Rear Lower Suspension Holder (RR) 1 SW-339013 228016-Seal SWORKz 1/8 BBS Precision Plastic Shock Seal Part (2 Sets) 2 SW-228016-Seal 339014 S35-GT2.2 FTE Series Aluminum Front Upper Arm Suspension Holder (UFR) 1 SW-339014 224007L3.5-6 SWORKz 1/10 Plastic Ball End XS (5.5mm) 6 SW-224007L3.5-6...
Page 43
S35-4/E Series Pro-composite Carbon Front Lower Arm Cover (1.5mm)(2PC) SW-340022-20 S35-4/E Series Pro-composite Carbon Front Lower Arm Cover (2mm)(2PC) SW-348003-10 SWORKz S35-4 Series Pro-composite Carbon Arched-Bridge-System Rear Lower Arm Cover(1.0mm)(2PC) SW-348003-15 SWORKz S35-4 Series Pro-composite Carbon Arched-Bridge-System Rear Lower Arm Cover(1.5mm)(2PC) SW-348003-20 SWORKz S35-4 Series Pro-composite Carbon Arched-Bridge-System Rear Lower Arm Cover(2.0mm)(2PC)
Need help?
Do you have a question about the S35-GT2.2FTE Series and is the answer not in the manual?
Questions and answers