Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Photoneo MotionCam-3D
Summary of Contents for Photoneo MotionCam-3D
- Page 1 MotionCam-3D User Manual and Installation Instructions ...
- Page 2 11/2020 Thank you for choosing Photoneo® MotionCam-3D. Please take a few minutes to read this manual and become familiar with the device. For more information on our products, accessories, replacement parts, software and services, see our website photoneo.com/motioncam-3d/ or contact our team at ...
- Page 3 Please note the following: ⚠ WARNING Photoneo products may only be used in accordance with relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Photoneo. Proper transport, storage, installation, assembly, commissioning, operation, and maintenance are required to ...
- Page 4 Trademarks All names identified by ® are registered trademarks of Photoneo s.r.o. The remaining trademarks in this publication may be trademarks that when used by third parties for their own purposes could violate the rights ...
-
Page 5: Table Of Contents
Scanning Parameters 21 Operation Temperature 21 Cleaning Instructions 27 Compliance with Standards 28 28 Laser Classification 28 Degree of Protection 28 Warranty 28 Dimensions and Illustrations 29 Bottom View: Mounting Plate 29 support@photoneo.com MotionCam-3D - User Manual and Installation Instructions 5/33 ... - Page 6 11/2020 Bottom View: Detail A 30 Front View: Projection Unit and Camera Unit 31 Contact Information 32 support@photoneo.com MotionCam-3D - User Manual and Installation Instructions 6/33 ...
-
Page 7: Product Overview
11/2020 Product Overview MotionCam-3D is a high accuracy and high resolution snapshot 3D area scanning device for large work areas that can be in motion. The product is based on a patented CMOS sensor and Parallel Structured Light technology developed by ... -
Page 8: Laser Device
The device uses the following labels and warning systems. Apart from the laser aperture label, all are located on the back panel of the device. Laser radiation hazard warning symbol. support@photoneo.com MotionCam-3D - User Manual and Installation Instructions 8/33 ... -
Page 9: Objects Suitable For Scanning
Objects Suitable for Scanning MotionCam-3D uses laser light to acquire 3D data. It can capture dynamic scenes as well as static ones. Smoke and particles dispensed in the air will negatively influence the 3D data. Always bear in mind that ... -
Page 10: Scope Of Delivery
Desktop PoE injector (input: 90 ~ 264 VAC, output: 33.6 W, 56 V, IEEE802.3at) with power cable (1.8 m) ■ Ethernet cable M12-X male - RJ45 male, 5 m, PUR ■ NOTICE Software components are needed for operation of the MotionCam-3D. See section C onfiguration for more information. ... -
Page 11: Installation
Figure 2: Mounting plate Connect MotionCam-3D to the computer or local network and plug it into the power. See the section Powering the device & Data connection for more details. 4. Download and install the PhoXi Control application from the Photoneo webpage. ... -
Page 12: Powering Through Poe Connector
Powering Through PoE Connector Connect 1 Gbps capable (standardly delivered) ethernet cable to the PoE injector IN port Connect the M12-X RJ45 cable to MotionCam-3D and to the PoE injector OUT port Plug in the power cable of the PoE injector ... -
Page 13: Status Leds
Activity on link Green No activity on link Off Link is down 4 ETH2 Green Gigabit ethernet connected Off No gigabit ethernet Figure 6: Status LEDs of correctly working device support@photoneo.com MotionCam-3D - User Manual and Installation Instructions 13/33 ... -
Page 14: Supported Network Topologies
Figure 7: Direct connection Scanner connected to a switch ■ Figure 8: Connected to a switch The following network topology is not supported by MotionCam-3D: Scanner connected to a router: ■ Figure 9: Connecting the Scanner through router is not supported ... -
Page 15: Mounting Restrictions
NOTICE It is recommended to mount MotionCam-3D on a metal plate that will act as a thermal bridge and dissipate the heat produced by the processing unit away from it. support@photoneo.com MotionCam-3D - User Manual and Installation Instructions... -
Page 16: Configuration
11/2020 Configuration PhoXi Control PhoXi Control is a computer application that acts as a driver for the Photoneo scanning devices. It allows the user to control the MotionCam-3D manually through graphical user interface or programmatically through the provided API. The GUI is primarily used to set up the scanning environment, to configure advanced scanning parameters and ... - Page 17 You can download the latest version of PhoXi Control from our website www.photoneo.com/3d-scanning-software/ For more information about the PhoXi Control application, please refer to the P hoXi Control User Guide . support@photoneo.com MotionCam-3D - User Manual and Installation Instructions 17/33 ...
-
Page 18: Hardware Parameters
Rated operating current I (I ) 0. 360 A (0.6 A) e max Minimum Power 33 W Shielding Fully Shielded RJ45 Transfer data rate 1 Gbit Maximum recommended cable length 20 m support@photoneo.com MotionCam-3D - User Manual and Installation Instructions 18/33 ... -
Page 19: 24 V Power Connector
1 A (2 A) e max Minimum Power 60 W Maximum recommended cable length 20 m * * for cable length over 10 m please ensure operating voltage at minimum 28 V support@photoneo.com MotionCam-3D - User Manual and Installation Instructions 19/33 ... -
Page 20: Projection Unit
Overall operating temperature From 0 °C to 45 °C Humidity From 0 % to 95 % non-condensing Atmospheric pressure From 1080 hPa to 660 hPa (corresponding to an altitude of -1000 m tp 3500 m) Maximum acceleration 20 ms -2 support@photoneo.com MotionCam-3D - User Manual and Installation Instructions 20/33 ... -
Page 21: Scanning Parameters
NVIDIA Pascal™ Architecture GPU with 256 CUDA cores Operation Temperature It is recommended to let the device reach operating temperature before use by being powered on for at least 15 minutes. support@photoneo.com MotionCam-3D - User Manual and Installation Instructions 21/33 ... - Page 22 0.30 mm Temporal noise (dynamic) 0.10 mm Point size (static, at sweet spot) 0.25 mm Accuracy (static) 0.15 mm Temporal noise (static) 0.05 mm Figure 16: MotionCam-3D S scanning range support@photoneo.com MotionCam-3D - User Manual and Installation Instructions 22/33 ...
- Page 23 1.0 mm Temporal noise (dynamic) 0.15 mm Point size (static, at sweet spot) 0.52 mm Accuracy (static) 0.50 mm Temporal noise (static) 0.10 mm Figure 17: MotionCam-3D S+scanning range support@photoneo.com MotionCam-3D - User Manual and Installation Instructions 23/33 ...
- Page 24 0.50 mm Temporal noise (dynamic) 0.10 mm Point size (static, at sweet spot) 0.37 mm Accuracy (static) 0.25 mm Temporal noise (static) 0.05 mm Figure 18: MotionCam-3D M scanning range support@photoneo.com MotionCam-3D - User Manual and Installation Instructions 24/33 ...
- Page 25 0.60 mm Temporal noise (dynamic) 0.10 mm Point size (static, at sweet spot) 0.52 mm Accuracy (dynamic) 0.30 mm Temporal noise (static) 0.05 mm Figure 19: MotionCam-3D M+ scanning range support@photoneo.com MotionCam-3D - User Manual and Installation Instructions 25/33 ...
- Page 26 1.25 mm Temporal noise (dynamic) 0.15 mm Point size (static, at sweet spot) 0.72 mm Accuracy (static) 0.90 mm Temporal noise (static) 0.10 mm Figure 20: MotionCam-3D L scanning range support@photoneo.com MotionCam-3D - User Manual and Installation Instructions 26/33 ...
-
Page 27: Cleaning Instructions
Remove the film from the glass using peel tabs with wooden or plastic tips. The film removes any dirt or particles from the glass. w ww.photoniccleaning.com/product-p/rfcr.htm support@photoneo.com MotionCam-3D - User Manual and Installation Instructions 27/33 ... -
Page 28: Compliance With Standards
Laser class of the scanner is determined according to EN 60825-1:2014 Equipment classification and requirements standard. MotionCam-3D are laser class 3R devices. The laser class was tested by an independent certification body Lasermet Limited which has issued certification reports No. 1830 and1997b. ... -
Page 29: Dimensions And Illustrations
11/2020 Dimensions and Illustrations Bottom View: Mounting Plate Figure 22: Bottom view of MotionCam-3D support@photoneo.com MotionCam-3D - User Manual and Installation Instructions 29/33 ... - Page 30 11/2020 Bottom View: Detail A Figure 23: MotionCam-3D - Detail A support@photoneo.com MotionCam-3D - User Manual and Installation Instructions 30/33 ...
- Page 31 11/2020 Front View: Projection Unit and Camera Unit Figure 24: Projection unit and camera of MotionCam-3D support@photoneo.com MotionCam-3D - User Manual and Installation Instructions 31/33 ...
- Page 32 Plynárenská 1, 821 09 Bratislava, Slovak Republic Identification number: 47 353 309 Tax ID: 2023884907 EU VAT ID: SK2023884907 Sales contact: sales@photoneo.com , +421 948 766 479 Technical support: support@photoneo.com , +421 948 666 730 support@photoneo.com MotionCam-3D - User Manual and Installation Instructions 32/33 ...
- Page 33 11/2020 Photoneo s.r.o. Plynárenská 1 82109, Bratislava Slovakia support@photoneo.com MotionCam-3D - User Manual and Installation Instructions 33/33 ...
Need help?
Do you have a question about the MotionCam-3D and is the answer not in the manual?
Questions and answers