Subscribe to Our Youtube Channel
Related Manuals for Grace FELiX2
Summary of Contents for Grace FELiX2
- Page 1 2 Channel Instrument Preamplifier / EQ / DI Owner’s Manual Rev. A Grace Design, 4689 Ute Highway, Lyons, CO 80503 303.823.8100 / info@gracedesign.com www.gracedesign.com...
-
Page 2: Table Of Contents
1 Welcome If you’re reading this, you are probably a working musician or out when you look down at that stage floor, it will be down audio professional of some kind. You’ve spent years honing there shining back up at you, making you sound better and your craft with long, lonely hours spent strumming, picking, your job easier. -
Page 3: Safety Marking Symbols
Contact Grace Design for repair and upgrade this manual, refers to important instructions. information. In the event that your Grace Design Felix 2 Read this manual thoroughly before operating needs to be returned to the factory, contact us for a return this equipment. -
Page 4: Top Panel Controls And Features
5 Top Panel Controls and Features 13 14 Gain controls (CH1&2) Signal / clip LED indicator (CH1&2) High Pass Filter (notch) / Notch filter (CH1&2) Low frequency shelving cut and boost (CH1&2) Parametric Midrange cut and boost (CH1&2) Parametric Midrange frequency select (CH1&2) Parametric Midrange Q factor (CH1&2) High frequency shelving cut and boost (CH1&2) Boost level... -
Page 5: Back Panel Controls And Features
6 Back Panel Controls and Features PUSH Universal 100-240VAC power supply input module 10. Amp Output DI Ground lift switch 11. Effects Return CH1 DI output 12. Effects Send CH1 DI output source select 13. Amp Source Select switch CH1 DI output line / mic level select 14. -
Page 6: Ch1 Xlr Mic Input
TRS 1/4” jack wired Tip signal to CH2, Ring signal normaled to There is an internal jumper that allows the output level of the CH1, and Sleeve ground. If you are using CH1 with this input, INSERT send to be adjusted between 0dB, -6dB and -16dB, remember to select the ‘line’... -
Page 7: Headphone Output
8.8 HEADPHONE OUTPUT 8.9 100-240VAC POWER INPUT This is a 1/8” mini style stereo headphone jack for monitoring Felix 2 is powered by a Class II Universal AC power supply. This signals via your headphones, IEMs, earbuds etc.. This output means that no matter where your musical wanderings take level is the same as the amp out, so the top panel amp out you, you can plug Felix 2 in to the wall and it will work. -
Page 8: Filtering And Eq
a TRS output jack, you can simply use a standard TRS cable to thin or just downright weird. Again, the rule of thumb here is connect both sources to Felix 2, then EQ and blend each signal whatever sounds right is probably right. accordingly. -
Page 9: Output Controls And Settings
frequency. This is used predominantly to find and remove a controls is very wide, which enables targeting of specific sonic specific problem frequency that may be feeding back through areas of a multitude of instrument or pickup types. stage monitors or amps, or to simply cut out a very specific, MID EQ GAIN narrow unwanted part of an instrument’s frequency range. -
Page 10: Footswitch Controls
tuner outputs on the rearpanel and also of the headphone illuminates RED. jack on the right sidepanel. If you are using a stage amp, use this control as your master level. Correct input gain settings for 9.7 SIDE PANEL CONTROLS your sources, with the signal LED showing mostly green, should Felix 2 has a lot going on, more than we could fit on the rear not be adjusted to alter your stage amp level. -
Page 11: Adjusting Internal Jumpers
Since sound travels at about a foot per millisecond, this is equivalent to about 6”, so if your mic is mounted to your PHASE SHIFT instrument at about 6” from the strings, you would be time aligned with this setting. PHASE (deg) ALL PASS FILTER TIME... -
Page 12: Internal Jumper Locations
mode (jumper center and left) keeps both DI outputs active regardless of which channel is selected. EXCLUSIVE output mode (jumper center and right) mutes the inactive channel’s DI output. This is set to DUAL ISO mode at the factory. J14 and J17 - These jumpers apply a signal pad to the insert send, one for each channel. - Page 13 Lower Board Jumpers CH 1 INST GAIN J6 = CH1 12V OFF LOW GAIN J7 = CH2 12V OFF J19: INSERT SEND CH1 J7 = CH2 12V RING HIGH GAIN J7 = CH2 12V TIP J6 = CH1 12V RING J6 = CH1 12V TIP J18: INSERT RET STEREO...
-
Page 14: Fx Insert Connections
11 FX Insert Connections The insert send and return jacks are both TRS, with CH1 on the tip and CH2 on the ring. Insert operation with FELiX in MIX mode ‘send’ ‘return’ Mono Send / Stereo Return For using mono in, stereo out FX units • TS plug from ‘send’ to TS plug to FX input CH1 FX (standard 1/4”... -
Page 15: Connection Diagram
12 Connection Diagram... -
Page 16: Block Diagram
13 Block Diagram... -
Page 17: Specifications
14 Specifications GAIN RANGE (Input to DI Output) CH1 MIC Low Gian: 17-62dB 21-62dB / High gain: 22-63dB CH1 Inst Low Gain: 3-48dB / High Gain: 17-62dB CH2 Inst -1-37dB Boost 0-9dB THD+N 1kHz, 22Hz-22kHz BW (MIC Input to DI Output line level out) @ 20dB Gain +10dBu out <0.015% @ 40dB Gain +10dBu out... -
Page 18: Cleaning And Maintenance
In no event will Grace Design be liable for lost profits or any other incidental, consequential or Exemplary damages, even if Grace Design is aware of the possibility of such damages. In no event will Grace Design’s liability exceed the purchase price of the product. -
Page 19: Manual Revisions
17 Manual Revisions Revision Page Change Date Initials Initial release 03/05/2021...
Need help?
Do you have a question about the FELiX2 and is the answer not in the manual?
Questions and answers