Storing Your Grass Trimmer; Maintenance - Worx WG183 Manual

Only one green light
( ) is
illuminated.
No light is
illuminated.
Only one light is
flashing twice per
cycle.
Only one light is
flashing three times
per cycle.
Only one light is
flashing four times
per cycle.
OPERATION INSTRUCTIONS
WARNING! The charger and battery pack are
specially designed to work together so do not
attempt to use any other devices. Never insert or allow
metallic objects into your charger or battery pack
connections because of an electrical failure and hazard
will occur.
10
1.AUTOMATIC LINE FEED SYSTEM
When initially switching on the trimmer, a small length of
line is fed out.
A 'clattering' noise will be heard for a short time. This is
normal and is caused by the line being cut by the line
cutter. Once the line is cut to the correct length, the
'clattering' noise will stop and the trimmer motor will run
at full speed.
To feed more line, stop the trimmer completely, then
restart, allowing the motor to reach full speed. Repeat this
until you hear the 'clattering' noise of the line cutting. (Do
not repeat this procedure more than 6 times)
2 . MANUALLY FEEDING THE LINE (See Fig. H)
Press and release manual line feed button, whilst gently
pull out the lines until the lines reaches the line cutter.
When the required amount of line is fed out, gently pull on
the second line (there is no need to press the manual line
feed button again). If the line extends past the line cutter,
too much line has been fed out. If too much line is fed out,
remove the spool cap and rotate the spool anti-clockwise
until the line is at the desired length.
Removing the Cap (See Fig. I)
Press and hold in the two latches. Pull the spool cap
away from the Cutting Head. Keep the cap and spool
holder clean from debris. To replace the cap, press it
firmly towards the spool holder. Ensure that it is correctly
connected by trying to remove it without depressing the
two latches.
Cordless Grass Trimmer
At least one battery is almost
depleted and needs to be
charged.
At least one battery is not fully
installed or battery may be
defective.
At least one battery is over
discharged (please refer to the
battery charge condition), please
recharge the two batteries at
once before use again or storage.
At least one battery is hot, wait
for them cool down before start
again.
The machine is over load. Raise
the cutting height or push slowly.
Changing the Line Spool (See Fig. K, L)
First take off the cap and remove the old spool. Place new
spool into cutting head. Feed one line through the eyelet,
then repeat for second line (See Fig. L).
Release line from cleat on the Spool. Reattach the cap.
WARNING! Your Trimmer is designed to only use line with a
maximum diameter of 0.065"(1.65mm). Only use nylon line.
IMPORTANT - Always wind the line onto the upper section
of the spool first.
3. MANUALLY WINDING THE LINE (SEE FIG.M, N, O, P)
Take approximately 16ft (5 m) line and insert 5/8" (15 mm)
of line into one of the holes in the upper section of the
spool. Wind the line in the direction of the arrows on the
top of the spool.
Leave approximately 3.9'' (100 mm) of line unwound and
place it into the cleat. Repeat on the lower section of spool.
Care should be taken to ensure that the line is neatly coiled
on the spool. Failure to do so will impair the efficiency of
the automatic line feed. Then fit the spool as described
above in "Changing the Line Spool".
STORING YOUR GRASS
TRIMMER
Always remove the battery pack from
your trimmer after use.
To store your grass trimmer
The trimmer is provided with a hanging slot for
storing the trimmer on the wall. (See Fig. Q)
Store in a dry place where the trimmer and battery
can be protected from damage.

MAINTENANCE

Always remove the battery pack from your trimmer
after use.
Always check the product prior to being used for any
damage.
After use, disconnect the battery from the tool and check
for damage.
Your power tool requires no additional lubrication or
maintenance. There are no user serviceable parts in
your power tool. Never use water or chemical cleaners to
clean your power tool. Wipe clean with a dry cloth. Always
store your power tool in a dry room temperature location.
Keep the motor ventilation slots clean. Keep all working
controls free of dust.
FOR BATTERY TOOLS
The ambient temperature range for the use and storage of
tool and battery is 0℃-45℃.
The recommended ambient temperature range for the
charging system during charging is 0℃-40℃.
EN