Bosch Professional GIS 1000 C Original Instructions Manual page 7

frared sensor, from moisture, snow, dust and dirt. The
reception lens could fog up or become contaminated
and distort the measurements. Incorrect settings on the
tool and other atmospheric influences may make the
measurements inaccurate. Object temperatures could be
shown to be hotter or colder than they are, which may
present a danger if touched.
Correct temperature measurements are only possible
u
if the set emissivity and emissivity of the object
agree, and the correct reflected temperature is set.
Otherwise, object temperatures could be shown to be
hotter or colder than they are, which may present a
danger if touched.
Safety Instructions When Using Thermocouples
Thermocouples must not be used in live electrical sys-
u
tems. This poses a risk to life!
Using a thermocouple means contact with the object
u
measured. Therefore, watch out for potential dangers
due to temperature, voltage or a chemical reaction.
Product Description and
Specifications
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The measuring tool is intended for contactless measurement
of surface temperature, ambient temperature and relative
humidity. It calculates the dew point temperature and indic-
ates thermal bridges and mould risk. Mould spores cannot
be detected with the measuring tool. However, it can help to
detect conditions early on that can encourage mould growth.
The measuring tool may not be used to measure the body
temperature of humans or animals or for other medical pur-
poses.
The measuring tool is not suitable for measuring the surface
temperature of gases.
Temperature measurement in liquids is only possible using a
commercially available thermocouple (connection type K),
which can be connected to the measuring tool via the
interface (25) intended for this.
The light of this measuring tool is intended to illuminate the
direct work area of the measuring tool in order to take pic-
tures.
The laser points must not be used as a laser pointer. They
are solely for marking out the area being measured.
The measuring tool is suitable for indoor and outdoor use.
Product Features
The numbering of the product features shown refers to the il-
lustration of the measuring tool on the graphic page.
(1) Micro USB port flap/thermocouple (type K) connec-
tion
(2) Laser beam outlet aperture
Bosch Power Tools
(3) Battery pack/battery adapter/battery compartment
cover release button
(4) Measure button/on button
(5) Humidity and ambient temperature sensor
(6) Serial number
(7) Laser warning label
(8) Micro USB cable
(9) Save/send button (Bluetooth®)
(10) Right-hand function button
(11) Right-hand arrow button
(12) On/off button
(13) Down arrow button/zoom out
(14) Light on/off button
(15) Left-hand arrow button
(16) Up arrow button/zoom in
(17) Left-hand function button
(18) Display
(19) Protective cap for humidity and ambient temperat-
ure sensor
(20) Carrying strap lug
(21) Protective cap for infrared reception lens
(22) Camera
(23) Infrared beam reception lens
(24) Light
(25) Type K connection for thermocouple
(26) Micro USB port
A)
(27) Battery adapter cover
A)
(28) Battery adapter cap
(29) Battery bay
A)
(30) Battery
(31) Battery compartment cover
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Display elements (see figure A)
(a) Date/time (see "<Time & Date>", page 15)
(b) Measuring frame (see "Measured area for surface
temperature measurements", page 11)
(c) Status indicator:
Measuring tool is ready to measure; press
the measure button (4).
(Continuous) measurement in progress;
lasers are switched on.
Measurement complete, lasers are
switched off, measurement results are
fixed.
Contact temperature mode, lasers are
deactivated, measurement taken only via
thermocouple.
English | 7
A)
1 609 92A 62P | (14.10.2020)