Bosch Indego XS 300 Original Instructions Manual page 25

Separate lawn area with separate docking station (see
figure H, right side): The mower can be used on up to three
different lawn areas. For an additional lawn area, a separate
docking station (see figure A) and the necessary perimeter
wire and pegs are required. If a schedule or the „Bosch
AUTO" calendar function is selected it will cut the grass of
the area is it in, within the time slots.
Switch off the mower when transporting it between different
lawn areas.
Note: software updates have to be carried out on the mower
in every docking station.
To help remember which docking station belongs to which
garden, it is recommended to label the docking stations with
the lawn area number and description when storing them for
winter.
Without separate docking station: It is possible to connect
the lawn areas by placing the perimeter wire between the
two lawn areas parallel to each other as close as possible
(see figure H, top left). The additional lawn area without
docking station is not recorded in the map memory and the
mower will not use the LogiCut cutting strategy in this lawn
area without the docking station. The maximum recommen-
ded lawn area without a docking station is 40 m
will mow until it runs out of battery and will need to be car-
ried back to the docking station for charging.
Mowing
Do not let children ride the mower.
u
Press the stop button on top of the mower before lift-
u
ing. Always lift the mower by its handle. (see figure F)
Make sure the cutting area is free of small animals such as
hedgehogs or tortoises.
After successful installation you can either immediately be-
gin to mow by confirming „Mow now" on the display, or wait
for the next scheduled cutting period, as programmed by the
Bosch AUTO Calendar Function (previous setting required).
A mowing schedule can also be set up according to your
needs.
The mower must mow a lawn area 3 times completely (do 3
full cuts) to learn the lawn area. During the learning phase,
the visual result may not be optimal.
Approximate runtimes for complete lawn coverage using Lo-
giCut are listed below. Please note that the runtimes will vary
depending on the lawn complexity and number of objects
within the garden.
2
100 m 4 h
2
300 m 11 h
Set a schedule with frequent repetitions. This achieves good
mowing results, the battery charge will last longer and you
avoid debris on the lawn.
When the mower is mowing
In "manual" mode, the mower works until the lawn is
mowed. Mowing is interrupted only for charging the battery.
When the lawn area is mowed, the mower returns to the
docking station.
Bosch Power Tools
In the programmable „Schedule" mode or with the „Bosch
AUTO" calendar function, the mower operates continuously
for a set period of time. Mowing is interrupted only for char-
ging the battery. If the lawn area is mowed before the time
period expires, the mower returns to the dock.
To stop mowing prematurely, press the Stop button or send
the mower back to the docking station pressing the confirm
button ✓.
Energy saving mode
The mower reduces its energy consumption by automatically
switching off the power in the perimeter wire when it is not
mowing and not being charged.
To wake up the mower manually from the energy saving
mode, press the confirm button ✓and afterwards select
either "Mow now" or another "Mowing mode", while the
mower is in the docking station.
When the "Schedule" mode or the "Bosch AUTO" calendar
function becomes active, the signal to the perimeter wire is
automatically started.
Sensors
2
. The mower
The mower is equipped with the following sensors:
– The lift-up sensor is activated when the mower is lifted.
– The rollover sensor detects when the mower tips over.
– The tilt sensor is activated when the mower reaches a
slope angle of 32°.
When one of the sensors is activated, e.g. the lift-up sensor,
the drive motors and cutting blades are stopped. A message
is indicated in the display, e.g. "lift-up".
– The obstacle sensor detects objects/obstacles alongside
the entire front edge of the mower and causes a change of
direction.
Battery charging
The battery is equipped with temperature monitoring that al-
lows charging only if the battery internal temperature is in
the range between 5 °C and 45 °C.
The lithium-ion battery is supplied partially charged. It is re-
commended to charge the mower during installation of the
perimeter wire in the docking station.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not damage the battery.
When the battery is run flat or discharged, the mower is shut
off by means of a protective circuit: the blades no longer
move.
Updating the Software (see figure K)
To update the software, you need a USB.org stick (FAT 32
formatted) and a USB OTG cable.
When a new software version is available, you can find it on
the Internet under "www.bosch-diy.com/indego-help". Load
the "IN7xxxx.bin" file onto the USB.org stick.
Turn the mower over and remove the cover from the USB
port. Connect the USB OTG cable with the USB.org stick.
English | 25
F 016 L94 037 | (11.11.2020)