1. Manuals
  2. Brands
  3. rollease acmeda Manuals
  4. Accessories
  5. ZIPSCREEN
  6. Installation manual

rollease acmeda ZIPSCREEN Installation Manual

Hide thumbs Also See for ZIPSCREEN:
Table of Contents

Advertisement

Quick Links

INSTALLATION MANUAL
Skyline Bottom Up
ZIPSCREEN
INSTALLATION MANUAL
August 2019

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ZIPSCREEN and is the answer not in the manual?

Questions and answers

Related Manuals for rollease acmeda ZIPSCREEN

Summary of Contents for rollease acmeda ZIPSCREEN

  • Page 1 INSTALLATION MANUAL Skyline Bottom Up ZIPSCREEN INSTALLATION MANUAL August 2019...

  • Page 2: Table Of Contents

    DISCLAIMER INTRODUCTION This Installation manual for Zipscreen has been produced by Rollease Acmeda to supply the necessary information for the safe and correct installation of Zipscreen. DISCLAIMER Rollease Acmeda has used reasonable care in preparing the information included in this document, but makes no representations or warranties as to the completeness or accuracy of the information.

  • Page 3: Section A | Tools And Additional Items Required

    Measuring Tape • Spirit Level ADDITIONAL ITEMS REQUIRED (NOT SUPPLIED) To install a Zipscreen, the following non-stocked items are required: • Fixings for Box/Open Brackets/Hardware (ensure appropriate fixings are used to suit application) • Trims to conceal packing (if required) Page.

  • Page 4: Blind Items Required

    RIVETS / SCREWS - OPEN BRACKETS QUANTITY AS REQUIRED NOTE: Store Idler/Spring Adapter retaining clip until required (can be left in adaptor as shown) Page. 4 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...

  • Page 5: Section B | Installation

    STEP 1 – CHECK FOR OBSTRUCTIONS Check for any obstructions that may interfere in installation. E.g. If there is an architrave at the bottom of a post that the Zipscreen is to be installed into, ensure you prepare the space for the installation.
  • Page 6 (Blind width is specified in initial check and measure) W1 is greater than W2 and W3 Proceed to Step 6 for Side Fix applications, or Step 7 for Face Fix applications Page. 6 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...
  • Page 7 Ensure the finished W1 width = Blind Width (Blind width is specified in initial check and measure) STEP 7 – CHECK AND ENSURE THE INSTALLATION SPACE IS LEVEL & SQUARE Page. 7 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...
  • Page 8 Note: Whilst installing the shade (in the next sections), ensure that the base of the side guides should not be lower than the measured highest point on floor/ground. Page. 8 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...

  • Page 9: Part B - Spring Pre-Tensioning

    The above charts are indicative only and indicate the minimum number of pre-turns required. Due to variances in fabric weights, additional ballast weight and installations the optimum number of pre-turns will vary. Pre-turns can be adjusted during installation. Page. 9 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...
  • Page 10 The above charts are indicative only and indicate the minimum number of pre-turns required. Due to variances in fabric weights, additional ballast weight and installations the optimum number of pre-turns will vary. Pre-turns can be adjusted during installation. Page. 10 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...
  • Page 11 The above charts are indicative only and indicate the minimum number of pre-turns required. Due to variances in fabric weights, additional ballast weight and installations the optimum number of pre-turns will vary. Pre-turns can be adjusted during installation. Page. 11 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...
  • Page 12 The above charts are indicative only and indicate the minimum number of pre-turns required. Due to variances in fabric weights, additional ballast weight and installations the optimum number of pre-turns will vary. Pre-turns can be adjusted during installation. Page. 12 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...
  • Page 13 ‘click’ is heard. Pre-turn spring for number of times indicated in Spring tensioning charts. A click will be heard for each turn. Page. 13 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...

  • Page 14: Part C - Cover Assembly

    RECESS FIX INSTALLATION OPTION NOTE: Holes are marked on end plate for drilling, For balanced installation drill holes at corresponding opposite sides of plate. Page. 14 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...

  • Page 15: Part D - Box Installation

    Note: 1. Use appropriate fixings to suit application. 2. Ensure End Plates are Aligned and Level. 3. Measure brackets end to end to confirm measurement is correct Page. 15 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...

  • Page 16: Part F - Open Bracket Installation

    User effort will be required to push the booster head/Idler pin into the adapter, a noticeable “click” will indicate that the component is correctly located. Page. 16 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...
  • Page 17 STEP 3 – UNLOCK PRE-TENSION HEAD AT STEP 4 – FEED THROUGH MOTOR CABLE SPRING END (FOR SPRING ONLY) (FOR MOTOR ONLY) Page. 17 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...
  • Page 18 If blind does not creep up, add more pre-turns. For motor operation, ensure wiring is correct and motor is operating correctly. For gear operation, ensure operation is smooth. Page. 18 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...

  • Page 19: Part H - Adjusting Pre-Turns (Spring Operated Blinds Only)

    If too many pre-turns are added, the blind will automatically raise. Note: Re-install and secure Retainer Clip when complete. Page. 19 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...

  • Page 20: Part I - Side Guide Installation

    L-Fixing Rail + U-Mounting Rail + Face Fix U-Mounting Rail + ear of end plate ear of end plate Locate ear of end plate with U-mounting rail Page. 20 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...
  • Page 21 SIDE FIX STEP 5 – REMOVE THE STOPS FROM THE FUNNEL IN THE INNER RAILS Use flat head screw driver to pry both stops out. Page. 21 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...
  • Page 22 When using the Ultra-Lock, the Latch Housings must be level with each other to ensure the Ultra-Lock Pins lock simultaneously. Adjust the position of the Inner Rails as required. Page. 22 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...
  • Page 23 Do not force the inner rail; it should be in its natural position. Page. 23 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...
  • Page 24 TOP LIMIT: Set top limit as required (should be as close BOTTOM LIMIT: Set to the lowest point possible. Ensure to the box as possible) seal is compressed as much as possible. Page. 24 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...

  • Page 25: Part J - Ultra-Lock Motor Settings

    Damage to shade may occur when operating motor prior to setting limits. Attention should be given. IMPORTANT Reversing motor direction using this method is only possible during initial set-up. Page. 25 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...
  • Page 26 To save lower limit, hold DOWN and STOP. Move shade to lock position by pressing the DOWN button on controller. Motor Response Approx. SECS Page. 26 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...

  • Page 27: Part K - Ultra-Lock Operation (Motor Operation)

    Note: Make sure that the FT mode is turned ON whilst locking and unlocking the blind. Refer to step 4 for instructions. Page. 27 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...

  • Page 28: Part L - Adjusting Motor Limits

    To save lower limit, hold DOWN Move shade to the desired controller. and STOP. lowest position by pressing the DOWN button. Motor Response Motor Response Approx. Approx. Page. 28 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...

  • Page 29: Part M - Ultra-Lock Operation (Manual Operation)

    STEP 2 - RELEASE THE WEIGHT BAR UNLOCKING STEP 1 - LOWER THE WEIGHT BAR ALL THE WAY DOWN PAST THE LOCKING POINT STEP 2 - RAISE THE WEIGHT BAR Page. 29 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...
  • Page 30 STEP 1 - ROTATE THE CRANK TO LOWER THE WEIGHT BAR ALL THE WAY DOWN PAST THE LOCKING POINT STEP 2 - ROTATE THE CRANK IN THE OPPOSITE DIRECTION TO RELEASE THE WEIGHT BAR Page. 30 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...

  • Page 31: Part N - Weight Bar Sb07 Latch Installation

    STEP 1 – BRING WEIGHT BAR TO DESIRED LOCKED POSITION Ensure shaft of the lock is retracted STEP 2 – SECURE LATCH TO U-MOUNTING RAIL Align lip of latch to U-Mounting Rail Page. 31 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...

  • Page 32: Part O - Insert Box / Cover

    PART O – INSERT BOX / COVER STEP 1 – SWING BOX COVER INTO BOX STEP 2 – SECURE COVER AT BOTH ENDS TOP AND CLIP INTO PLACE Page. 32 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...

  • Page 33: Section C | Installation Scenarios

    Adjust L fixing rails if required. If blind 02 occupies installation space allocated to blind 1 or blind 3, operational or installation problems will occur with these blinds. Page. 33 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...
  • Page 34 STEP 8 – ATTACH U MOUNTING RAILS ON BLINDS 1, 2 & 3 Rivet U Mounting rails to L fixing rails to all 3 blinds Page. 34 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...
  • Page 35 Ensure blind is correct width as specified in initial measure. FOR MORE THAN 3 BLINDS Apply same principles outlined in previous steps when there are several blinds side by side Page. 35 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...
  • Page 36 The side rails or entire systems may need to be removed to correct. Page. 36 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...
  • Page 37 • Trim weight bar length to correct size (based on actual installation width) Note: Tube and fabric may also require cor- recting Page. 37 Zipscreen Installation Manual | v4.2| August 2019 2019 ©Copyright All Rights Reserved Rollease Acmeda...
  • Page 38 Press P2, Down & Down on the remote and check the vated during motor installation. functionality of Impact Detection again. Note: For all Automate FT15 Motor information visit the RollEase Acmeda Website: http://www.rolleaseacmeda.com/au/products/product-detail/external-blind-motorisation-automate-ft15-motor Page. 38 Zipscreen Installation Manual | v4.2| August 2019...

Table of Contents