Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for rollease acmeda KLIP POD
Summary of Contents for rollease acmeda KLIP POD
- Page 1 KLIP (POD) & STEIN Installation Manual Outdoor wellness. Designed.
-
Page 2: Table Of Contents
INDEX 1 - INTRODUCTION ......................pag. 2 1.1 - Symbols used in the manual ................. pag. 2 1.2 - Personnel qualifications ..................pag.2 1.3 - Necessary equipment .................... pag. 3 1.4 - Before starting installation ..................pag. 3 2 - SAFETY ............................ -
Page 4: Introduction
The manual pages and their content shall not be deleted, rewritten or modified. This manual must be kept intact in all its parts, in an easily accessible place. ROLLEASE ACMEDA reserves the right to update the production and relevant manuals, without updating the previous producti on and manuals. -
Page 5: Necessary Equipment
1.2 - Necessary equipment The equipment listed below is required to ensure the correct installation of the mechanical and textile components and guarantee perfect operation of the finished product: » electric and pneumatic screwdriver; » complete set of tools; » equipment for working at heights (access platforms, ladders, scaffolding, overhead platforms, etc.) complying with current occupational safety regulations;... -
Page 6: Safety
IMPORTANT ROLLEASE ACMEDA guarantees the EC marking only for the products it supplies. Should any part be replaced with other components not guaranteed by ROLLEASE ACMEDA, the product warranty shall automatically become void and ROLLEASE ACMEDA shall not be held liable for any product malfunctioning. -
Page 7: Working Environment
WARNING If the awning must be installed on a floor higher than the ground floor, cordon the area off so as to ensure that nobody is under the awning when it is being lifted to the relevant floor. WARNING All handling and lifting operations shall be carried out with the utmost care, keeping unauthorized personnel at safe distance;... -
Page 8: Klip Components And Diagrams
- KLIP COMPONENTS AND DIAGRAMS 3.1 Tilting diagrams Awning dimensions with folded arms Arm length and inclination RECOMMENDED ARM: HOME RECOMMENDED DIMENSIONS: width 600 cm - projection 350 cm KLIP (POD) & STEIN INSTALLATION – REV 00... -
Page 9: Klip Xl Components And Diagrams
- KLIP XL COMPONENTS AND DIAGRAMS 4.1 Tilting diagrams Awning dimensions with folded arms Arm length and inclination RECOMMENDED ARM: URBAN RECOMMENDED DIMENSIONS: width 600 cm - projection 400 cm KLIP (POD) & STEIN INSTALLATION – REV 00... -
Page 10: Installation Tables And Technical Drawings
- INSTALLATION TABLES AND TECHNICAL DRAWINGS KLIP fixing bracket KLIP (POD) & STEIN INSTALLATION – REV 00... -
Page 11: Stein Components And Diagrams
- STEIN COMPONENTS AND DIAGRAMS 6.1 Tilting diagrams Awning dimensions with folded arms Arm length and inclination RECOMMENDED ARM: HOME RECOMMENDED DIMENSIONS: width 600 cm - projection 350 cm KLIP (POD) & STEIN INSTALLATION – REV 00... -
Page 12: Installation Tables And Technical Drawings
7 - INSTALLATION TABLES AND TECHNICAL DRAWINGS STEIN fixing bracket KLIP (POD) & STEIN INSTALLATION – REV 00... - Page 13 Quantity of brackets according to width and projection WARNING: brackets must be positioned within the hatched areas; outer brackets must be at a minimum distance of 40 mm from the edge of the square bar (not in the red hatching). KLIP (POD) &...
-
Page 14: Klip And Stein Installation
WARNING: Position and quantity of brackets depend on the awning width and projection. WARNING: The brackets must be positioned within the hatched areas. - Page 15 WARNING: the quantity of brackets depends on the awning width. WARNING: all brackets must be aligned...
- Page 16 Installation WARNING: insert the square bar into the supporting brackets. Close-up: fixing screw of the square bar awning WARNING: secure the square bar by placing the screws as shown in figure (detail A) KLIP (POD) & STEIN INSTALLATION – REV 00...
- Page 17 Fitting caps to brackets WARNING: after checking that the awning is firmly locked, cover the brackets with the caps (detail AWNING ADJUSTEMENT WARNING: Ensure that no persons, animals or property are near the awning during opening/closing operations. Open and close the awning to check its correct operations. KLIP (POD) &...
- Page 18 Angle adjustment WARNING: Loosen the side screws (1) of the arm support (Allen wrench 10). To increase the angle, loosen the socket-head cap screw (2) (Allen wrench 8). To decrease the angle, tighten the socket-head cap screw, lifting the terminal bar accordingly. After adjustment, check that the terminal bar is perfectly horizontal.
- Page 19 COUPLED VERSION The awning is supplied as shown in figure. WARNING: The awning is delivered pre-assembled, as much as possible. WARNING: Do not remove the arm lock. Arm coupling WARNING: in some cases arms must be coupled with the arm support. Fit the arm on the lever by inserting the pin (detail C).
- Page 20 Roller tube coupling WARNING: Couple the tube by inserting it on the pre-assembled joint and secure using the rivets provided. Fabric assembly WARNING: slide the fabric into the tube, centre it, lock it and roll it up. KLIP (POD) & STEIN INSTALLATION –...
- Page 21 Square bar assembly WARNING: Fit the brackets considering the position of arm supports and centre balance supports. Fit the square bar inserting it on the pre-assembled joint and secure with the rivets provided (detail Tube assembly with fabric WARNING: Insert the tube with the rolled up fabric into the square bar roller supports. First insert the side of the cap with hole into the plate with pin, then the winch/motor side, having pre- assembled the nuts if required.
- Page 22 Centre balance supports assembly WARNING: Fit the centre balance supports in correspondence of the reinforcement bands. Terminal profile coupling WARNING: Couple the terminal bar by inserting it on the pre-assembled joint and secure with the rivets provided. Fit the arm stoppers and the terminal bar connecting plates onto the terminal bar. KLIP (POD) &...
- Page 23 Terminal bar assembly WARNING: Assemble the terminal bar sliding the fabric into the relevant ogive. Centre the terminal bar with the fabric. Arms/Terminal bar fixing WARNING: Fix the arms to the terminal bar keeping them parallel to the square bar and tightening the M8x16 countersunk screws on the previously fitted plates.
- Page 24 Awning adjustment. WARNING: Place the arm stoppers properly. WARNING: Ensure that no persons, animals or property are near the awning during opening/closing operations. Open and close the awning; after checking that arms and fabric are perfectly aligned, fix the fabric to the terminal profile.
- Page 25 XL VERSION (Only for KLIP model) The following instructions only refer to the variations with respect to the previo us versions; therefore, follow the previously provided instructions for general operations. WARNING: fit the brackets within the hatched areas; outer brackets at a minimum distance of 40 mm from the edge of the square bar (not in the red hatching).
- Page 26 Arm assembly WARNING: If arm assembly is required, place the cam on the arm shoulder, fit it onto the lever and couple it with the pin. Awning adjustment WARNING: Remove the arm support cap (1) rotating it downwards. KLIP (POD) & STEIN INSTALLATION –...
- Page 27 Awning adjustment WARNING: Adjust the angle working on the screw (2) of the support (Allen wrench 8). Awning adjustment WARNING: After adjustment, secure by working on the dowel (3) (Allen wrench 3). Fit the cap (4) again, first by hooking it to the lower part, then to the upper part with a rotation.
- Page 28 Awning adjustment WARNING: Ensure the arms are parallel when the awning is closed. If they are not parallel, tighten or loosen the dowel (5) inside the lever (Allen wrench 8) supporting the arm accordingly and adjust the alignment when the awning is closed. Once the proper position has been set, lock the pin securing the dowel (6) located on the upper part of the lever (Allen wrench 3).
- Page 29 VERSION WITH PROTECTION HOOD (Models KLIP and STEIN) Brackets fitting WARNING: Fit the hood brackets straight onto the awning brackets. If the latter are not placed in the desired position, fit the hood brackets onto the wall. Hood fitting WARNING: Fit the hood onto the brackets, push it towards the wall and secure with M6 screws (Allen wrench 5).
- Page 30 Gasket fitting WARNING: Fit the gasket into the groove of the hood. Hood cover fitting WARNING: pre-assemble the M6 screw with the square nut, insert it into the cover slot, fit the covers and secure tightening the M6 screw (Allen wrench 5). KLIP (POD) &...
- Page 31 29 I KLIP (POD) & STEIN INSTALLATION – REV 00...
- Page 32 Lazio, 42 31045 Motta di Livenza (TV) - Italy t: +39 0422 1786080 f: +39 0422 1788073 info@Rollease Acmeda.it www.Rollease Acmeda.it...
Need help?
Do you have a question about the KLIP POD and is the answer not in the manual?
Questions and answers