Remote Control; Function Modes - Cardin Elettronica GL Series Instruction Manual

REMOTE CONTROL (fig. 6, 7 - pages 7, 8)
The system can be remotely activated using radio control devices;
to set the two functions to channels A-B-C-d use the selection
jumper "J2":
- position "1" function 1 selected, SEQUENTIAL COMMANd;
- position "2" function 2 selected, CH2 (binding posts 31,32).
The sequential command may be set (dip "1") to "open-block-
close-block" or "open-close".
Memory module (MM)
This is extractable, furnished with a non volatile EEPROM type
memory and contains the transmitter codes and allows you to
memorise up to 300 codes. The programmed codes are main-
tained in this module even during blackouts.
Note: Before memorising the transmitters for the first
time remember to cancel the entire memory content.
If the electronic card has to be replaced due to failure,
the module can be extracted from it and inserted into
the new card. Make sure that the module is correctly
inserted as shown on pages 7, 8.
Signal LEds "L4" (pages 7, 8):
Flashing quickly: cancels a single code
Flashing slowly: memorises a single code
Permanently lit: memory full.
TRANSMITTER COdE MANAGEMENT
A. Memorising a channel (using the associated transmitter)
B. Cancelling a channel (using the associated transmitter)
C. Cancelling all codes in memory
d. Memorising ulterior channels via radio (without having to
open the box in which the receiver is housed)
A. Memorising a channel (pages 7, 8):
1) Press and hold down button "P3" MEMO: The LEd "L4" will
flash slowly.
2) At the same time activate the transmitter which is to be memo-
rised.
3) Hold down button "P3" MEMO until LEd "L4" starts to flash
again.
4) Release the "P3" MEMO button: The LEd will continue to
flash.
5) Activate the transmitter again (same transmitter, same chan-
nel; if the channel is different or it is a different transmitter the
memorisation attempt will abort without success).
6) End of memorisation: the LEd "L4" will remain lit for 2 seconds,
indicating that the transmitter has been correctly memo-
rised.
Note: It is not possible to memorise a code which is already in
memory: if you attempt this, the LEd will switch off when you acti-
vate the transmitter (point 2). Only after releasing the button "P3"
MEMO will you be able to continue the memorising procedure. If
after activating the transmitter for the first time you wait for more
than fifteen seconds without activating the transmitter a second
time the memorisation attempt will abort without success.
B) Cancelling a channel (pages 7, 8):
1. Press and hold down the button "P2" dEL: the LEd "L4" will
flash quickly.
2. Activate the transmitter channel which is to be cancelled.
3. The LEd will remain lit for 2 seconds indicating that the trans-
mitter has been cancelled.
Note: If the user that you wish to cancel is not in memory, the
LEd will stop flashing; only after releasing the button "P2" will
you be able to continue the cancellation procedure.
For both the memorisation and cancellation procedures, if the
button is released before activating the transmitter the procedure
will abort.
C) Cancelling all user codes from memory (pages 7, 8):
1) Keep both buttons pressed down ("P2+P3") for more than
four seconds.
2) LEd "L4" will remain lit during the entire cancellation time
(about 8 seconds).
3) LEd "L4" switches off when the cancellation procedure has
terminated.
Note: When the memory is almost full the time required to search
for a user code could take up to 1 second from when the com-
mand was received. If led "L4" remains lit memory is completely
full. To memorise a new transmitter you will first have to cancel
a code from memory.
d) Memorising ulterior channels via radio
• Memorisation can be activated by radio (without opening the
receiver container) if jumper "J1" has been inserted (pages 7,
8).
1) Make sure that the jumper "J1" has been inserted (pages 7,
8).
2) Using a transmitter, in which at least
one channel button "A, B, C or d"
has already been memorised in the
receiver, press the button in the
transmitter as shown in figure.
Note: all the receivers within range when the channel button is
pressed (and which have at least one of the transmitter channel but-
tons memorised) will activate their signal buzzer "B1" (pages 7, 8).
3) Press one of the channel buttons on the same transmitter. The
receivers which do not contain that channel code will sound a
five-second long "beep" and will then deactivate. The receivers
which contain the channel code will sound a one-second long
"beep" and will enter the "programming via radio" mode.
4) Press the previously chosen channel buttons on the transmitter
which you wish to memorise; the receiver will sound 2 "beeps"
of half a second each after which the receiver will be ready to
receive another code.
5) To leave the programming mode wait for 3 seconds without
pressing any buttons. The receiver will sound a five-second
long "beep" and will then exit the programming mode.
Note: When the memory is entirely occupied the buzzer will sound
10 rapid "beeps" and will automatically leave the "programming
via radio" mode. Led "L4" will remain lit on the receiver. The
same signal is given each time you try to enter "programming
via radio" when the memory is full.
CONNECTING THE ANTENNA
Connect an ANS400 tuned antenna using a coaxial cable RG58
(impedance 50Ω) with a maximum length of 15 m.

FUNCTION MOdES

1) Automatic
This is selected by enabling automatic reclosing (dip "2" in position
"ON"). Starting from the completely closed position the sequential
command starts a complete function cycle that terminates with
automatic reclosing.
Automatic reclosing starts after the programmed pause period has
elapsed when the opening cycle has been completed or straight
away after the intervention of a photoelectric cell (the intervention
of a photoelectric cell causes the pause time to be reset).
during the pause time the symbol
pressing the blocking button during this period will stop automatic
reclosing and consequently stop the display from flashing.
Note: the courtesy light switches on each time a movement
command is given (both via cable or via radio) and switches off
30 seconds after the manoeuvre has been completed.
26
will flash on the display and