Page 1
Europe’s No. 1 in Water Technology Filter system for optimising drinking water Installation and operating instructions BWT bestaqua 14ROC Installation and operating instructions...
Setting the water quality using the blending function ........... Hygiene concept and stoppages..................Removing/replacing the RO cartridge................Instructions for installing and operating the BWT bestaqua 14ROC app ....... 3.5.1 Installing the app ......................3.5.2 Connecting your smartphone with the ROC using the app ........
This installation and operating manual (IOM) contains important instructions for safe and efficient use of the reverse osmosis device BWT bestaqua 14ROC. This installation and operating manual (IOM) is part of the device and must be constantly available at the place of operation for all staff members assigned.
Operater and safety notes This section gives an overview of all operational and safety aspects important for ensuring safe and fault-free operation. Despite all possible precautionary measures, some residual risk remains with any product, especially if it is used incorrectly. Warranty claims are void unless the provisions in this IOM are observed and followed.
Description of process The semi-permeable reverse osmosis membrane separates the raw water, which is supplied under high pressure (approx. 8 bar), into desalinated purified water (permeate) and the salty waste water (concentrate). The percentage ratio between the permeate produced and the amount of raw water used is called the WCF yield (%).
Observe the installation dimensions and bend radii when installing accessories (such as hoses, connection sets, etc.). The device bestaqua 14ROC is to be set up and operated with installed magnet plates. The device may not be hard plumbed to the water supply network, e.g. copper or brass.
The RO device must be connected to the hoses and the electrical socket. Use the device switch (situated on the rear of the device) to switch on the BWT bestaqua 14ROC. A green LED indicates that the RO unit is switched on.
Instructions for installing and operating the BWT bestaqua 14ROC app 3.5.1 Installing the app If you have not yet installed the BWT bestaqua 14ROC app, please scan the QR code below. This will take you to the website from which you can download the app.
The LED on the front of the below will be displayed. The are present, select the unit num- bestaqua 14ROC will light up blue. device is ready for permeate pro- ber which corresponds with the duction. The app shows “ready”.
14ROC bestaqua 14ROC TECHNICAL SERVICE MENU LOW WCF ALARM xxxxxx working OUTLET WATER SERVICE 8000 LITERS 9000 LITERS 10000 LITERS 11000 LITERS 12000 LITERS 13000 LITERS next exit The following message in the If a YELLOW CIRCLE is shown while permeate is being drawn, this...
Page 14
2.0 bar / 2.5 bar / 3.0 bar / 3.5 bar / 4.0 bar Note: In operation, the shut-off pressure will briefly exceed the bestaqua 14ROC set value. This is normal. bestaqua 14ROC bestaqua 14ROC TECHNICAL SERVICE MENU...
3.5.5 Fault messages bestaqua 14ROC bestaqua 14ROC bestaqua 14ROC bestaqua 14ROC bestaqua 14ROC pump faucet leakage fault cooling dripping water System loosing Leakage in the Possible causes: Running time Please report this pressure in “Tap” device itself! of the pump to BWT.
3, and was designed and manufactured according to the applicable engineering good practices. The BWT bestaqua 14ROC device does not have a CE mark according to article 6, section 5, of the directive 2014/68/EU, but the attached CE Declaration of Conformity is valid.
Further information on replacing the RO cartridge can be found in paragraph 3.3. 5.4 Disposal Procedure: The BWT bestaqua 14ROC consists of various materials which need to be disposed of properly. Please contact your contract partner for an expert and environmentally friendly disposal.
Page 20
BWT UK Limited BWT House, The Gateway Centre, Coronation Road,High Wycombe, Buckinghamshire, HP12 3SU Telephone: 01494 838 100 Email: enquiries@bwt-uk.co.uk www.bwt-uk.co.uk...