Id Net Network Via Rs232 - Address Switches - Honeywell Notifier IDR-2P User Manual

Address Switch settings (1=on)
1 2 3 4 5 6
1 1 0 0 0 0 0
2 0 1 0 0 0 0
3 1 1 0 0 0 0
4 0 0 1 0 0 0
5 1 0 1 0 0 0
6 0 1 1 0 0 0
7 1 1 1 0 0 0
8 0 0 0 1 0 0
9 1 0 0 1 0 0
10 0 1 0 1 0 0
11 1 1 0 1 0 0
12 0 0 1 1 0 0
13 1 0 1 1 0 0
14 0 1 1 1 0 0
15 1 1 1 1 0 0
16 0 0 0 0 1 0
17 1 0 0 0 1 0
18 0 1 0 0 1 0
19 1 1 0 0 1 0
20 0 0 1 0 1 0
21 1 0 1 0 1 0
22 0 1 1 0 1 0
23 1 1 1 0 1 0
24 0 0 0 1 1 0
25 1 0 0 1 1 0
26 0 1 0 1 1 0
27 1 1 0 1 1 0
28 0 0 1 1 1 0
29 1 0 1 1 1 0
30 0 1 1 1 1 0
31 1 1 1 1 1 0
32 0 0 0 0 0 1
33 1 0 0 0 0 1
34 0 1 0 0 0 1
35 1 1 0 0 0 1
36 0 0 1 0 0 1
37 1 0 1 0 0 1
38 0 1 1 0 0 1
39 1 1 1 0 0 1
40 0 0 0 1 0 1
41 1 0 0 1 0 1
42 0 1 0 1 0 1
43 1 1 0 1 0 1
44 0 0 1 1 0 1
45 1 0 1 1 0 1
46 0 1 1 1 0 1
47 1 1 1 1 0 1
48 0 0 0 0 1 1
49 1 0 0 0 1 1
50 0 1 0 0 1 1
51 1 1 0 0 1 1
52 0 0 1 0 1 1
53 1 0 1 0 1 1
54 0 1 1 0 1 1
55 1 1 1 0 1 1
56 0 0 0 1 1 1
57 1 0 0 1 1 1
58 0 1 0 1 1 1
59 1 1 0 1 1 1
60 0 0 1 1 1 1
61 1 0 1 1 1 1
62 0 1 1 1 1 1
63 1 1 1 1 1 1
IDR-2P, -2A & -6A Repeaters User Manual
2.8.3 ID
15
2 net Network via RS232 -
Address Switches
The ID 2 net is connected by one of two methods
as shown in the diagrams below. Connections
to the Isolated RS232 Board are shown in
Section 2.6. DC power connections are shown
in Section 2.8.1. The following must be set
during configuration:
a. The IDR repeater address; this is set in the
range 1 to 63 in binary by using the first 6
switches (A) on the Control Board. The
decode is given below. Addresses above
63 can only be set by using the Off-line
Configuration Tool (in this case the address
switches must all be set to 0). Address 0 is
not valid for ID 2 net.
b. Switch 7 must be set according to the type
of connection used by the repeater, in this
2
case 1 for ID net via an RS232 link.
c. Set switch 8 according to the type of
network used by the fire panel, in this case
1 for an ID 2 net network.
997-411-000-9, Issue 9
March 2008