Baumer PosCon OXE7 Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Baumer Manuals
  4. Accessories
  5. PosCon OXE7
  6. Operating instructions manual

Baumer PosCon OXE7 Operating Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Operating instructions.
PosCon OXE7 – Edge measurement in a new dimension.

Advertisement

Table of Contents
loading

Related Manuals for Baumer PosCon OXE7

Summary of Contents for Baumer PosCon OXE7

  • Page 1 Operating instructions. PosCon OXE7 – Edge measurement in a new dimension.

  • Page 2: Table Of Contents

    Object to be measured ......................... 55 Interfaces and outputs ........................57 Touch panel........................... 65 Memory ............................65 Safety instructions and maintenance ..................66 General safety instructions ......................66 Sensor inscriptions ........................66 en_BA_PosCon_OXE7.docx 2/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 3 Error correction and tips ......................69 Effects of deviations in the inclination angle ................. 69 The dependency of the measuring frequency ................70 Error correction ..........................72 Revision history .......................... 74 en_BA_PosCon_OXE7.docx 3/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 4: General Information

    Read these operating instructions carefully and follow the safety instructions! 1.2 Intended use The Baumer PosCon OXE7 sensor detects edges and outputs their position, distance, and center between edges. It was especially developed for easy handling, flexible use, and precise measurement. The red light laser ensures that the light beam is always visible, which makes sensor alignment easier and minimizes installation errors.

  • Page 5: Commissioning In 4 Steps

    = Enables the panel if locked <---- = Jump to run mode Setting the language English The language is selected and confirmed by pressing Deutsch SET for 2 seconds. Italiano Français en_BA_PosCon_OXE7.docx 5/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 6: Installation

    Now an object is slowly pushed toward the presumed zero point. The zero point is reached by the rising edge of the object when the value 0 mm is shown on the sensor display and the yellow LED switches. en_BA_PosCon_OXE7.docx 6/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 7: Measuring Mode

    3. When all conditions are met (see table on right), confirm by pressing Set for 2 seconds Reference surface too uneven 4. Enter thickness of the auxiliary plate (if present) Reference surface too small (<50 mm) en_BA_PosCon_OXE7.docx 7/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 8 3. When all conditions are met (see table on right), Reference surface too uneven confirm by pressing Set for 2 seconds Reference surface too 4. Enter thickness of the auxiliary plate (if present) small (<50 mm) en_BA_PosCon_OXE7.docx 8/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 9 Set for 2 seconds surface too large 4. Enter thickness of the auxiliary plate (if present) Installation angle too large Reference surface too uneven Reference surface too small (<50 mm) en_BA_PosCon_OXE7.docx 9/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 10: Measurement

    Right The sensor is equipped with a switching Left Right output that can be configured as a threshold or as a window via the DIGITAL OUT function. Point Window en_BA_PosCon_OXE7.docx 10/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 11: Connection

    Nevertheless direct contact between the eye and beam should be avoided. 3.1 Connection cable An 8-pole, shielded connection cable (connector) is required. Baumer connection cables with the following order codes are recommended:  10127844 ESG 34FH0200G (length 2 m, straight plug) ...

  • Page 12: Pin Assignment And Connection Diagram

    RS485 receive/transmit+ (A) Pin 7 BU = blue Ground GND Pin 8 RD = red sync in Input synchronization NOTE We recommend that you connect unused cables to GND (0V). en_BA_PosCon_OXE7.docx 12/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 13: Installation

    R1, R2, and R3 serve as a reference for sensor alignment during installation. "Left" and "Right" designations 13 mm are also important. Left Right Laser beam Level R3 Level R2 Level R1 en_BA_PosCon_OXE7.docx 13/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 14: The Reference Surface

    If there is no reference surface as a measuring level, the sensor should be aligned to the object. If the PosCon OXE7 sensor cannot be aligned at a right angle to the reference surface, the FLEX MOUNT function should be activated.

  • Page 15: Sensor Alignment

    Angle deviations can affect measuring accuracy (see Section Alignment errors). To facilitate sensor alignment, LIVE MONITOR monitor can be used as an aid. LIVE MONITOR continuously outputs the currently measured angle and the distance from the reference surface. en_BA_PosCon_OXE7.docx 15/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 16: Standard Installation

    In standard installation, the sensor is mounted at a right angle (90°) to the reference surface or the object (when there is no reference surface). On reference level on object en_BA_PosCon_OXE7.docx 16/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 17 Section "Function and definition“ - Reference point > "Interfaces and output-> "Analog End of measuring signal output". range Sde Measuring field 0 mm Measuring field width left width right Measuring field width en_BA_PosCon_OXE7.docx 17/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 18: Angled Installation

    This is particularly useful when space conditions do not allow any other installation option. See Section FLEX MOUNT. The object must be within the measuring field. +30 … 0° 0 … -30° Reference surface en_BA_PosCon_OXE7.docx 18/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 19 Left Right Left End of End of measuring Blind region Blind region measuring range Sde range Sde Measuring Measuring field field 0 mm 0 mm Reference Reference point point en_BA_PosCon_OXE7.docx 19/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 20: Practical Zero Point Search

    The zero point is reached by the left rising edge of the object when the value 0 mm is shown on the sensor display and the yellow LED switches. en_BA_PosCon_OXE7.docx 20/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 21: Installation Accessories

    With the mounting bracket for standard installation, the sensor can be mounted quickly and easily at a 90° angle to the reference surface. Mounting kit 11120705 Contents of this set: 90° mounting bracket Threaded plate 2x spherical head screw M4x35 Torx 1x Torx tool T20 en_BA_PosCon_OXE7.docx 21/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 22 ±30° with this mounting kit. Mounting kit 11126837 Contents of this set: 30° mounting bracket, vertical Threaded plate 2x spherical head screw M4x35 Torx 1x Torx tool T20 en_BA_PosCon_OXE7.docx 22/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 23: Configuration Via Touch Panel

    Rectangular measuring field activated This symbol appears on the left side of the screen when the measuring field is rectangular (AUTO). en_BA_PosCon_OXE7.docx 23/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 24 RS-485. The keys must be unlocked with a RS-485 command. When the locked keys are touched, the following text appears on the display: RS-485 locks the touch keys en_BA_PosCon_OXE7.docx 24/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 25 Object just under the measuring range limit or outside measuring field or invalid received insufficient received signal (e.g. soiling) signal (e.g. soiling) Green Supply voltage Short circuit Sensor ready for operation Check connection en_BA_PosCon_OXE7.docx 25/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 26: Function Tree

    5.2 Function tree The menu that can be accessed via the touch panel is shown below. en_BA_PosCon_OXE7.docx 26/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 27 27/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 28: Live Monitor

    = 0°) Left Right Distance Angle NOTE An angle of 0° means that the sensor is at a right angle to the reference surface. en_BA_PosCon_OXE7.docx 28/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 29: Measurement Type

    Distance in mm measured from the center of the measuring range of the sensor to the edge. Left Right Left Left Right Right Measuring value Measuring value in mm in mm en_BA_PosCon_OXE7.docx 29/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 30 Distance in mm measured from the center of the measuring range of the sensor to the edge. Left Left Left Right Right Right Measuring value Measuring value in mm in mm en_BA_PosCon_OXE7.docx 30/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 31 Output of the distance from the center of an object to the center of the measuring range in mm. Left Right Left Left Right Right Measuring Measuring value value in mm in mm en_BA_PosCon_OXE7.docx 31/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 32 Output of the distance from the center of a gap to the center of the measuring range in mm. Left Left Right Right Left Right Measuring value Measuring value in mm in mm en_BA_PosCon_OXE7.docx 32/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 33: Edge Height / Object Height / Gap Depth

    Depending on the circumstances in the customer application, it is possible to improve repeat accuracy up to a factor of 4 by filtering. In accordance with data sheet in Section 6.1. en_BA_PosCon_OXE7.docx 33/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 34: Flex Mount

    The axes are no longer referred to as X and Z, but as M and K When the FLEX MOUNT function is activated, this is indicated by an angle symbol on the left side of the display en_BA_PosCon_OXE7.docx 34/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 35 Minimum length of reference surface or auxiliary plate NOTE The following menu items TEACH REF and THICKNESS REF must be completed so that FLEX MOUNT can be activated. en_BA_PosCon_OXE7.docx 35/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 36 To ensure correct teaching-in of the reference surface, REF THICKNESS must always be completed after the angle teaching-in process. Only in this manner can the effective reference surface be determined with due regard to the thickness of the auxiliary plate. en_BA_PosCon_OXE7.docx 36/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 37 When FLEX MOUNT is activated, the measuring field and the digital switching output are reset to the standard setting (FLEX MOUNT = Maximum measuring field, DIGITAL OUT = 0 mm). en_BA_PosCon_OXE7.docx 37/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 38: Measuring Field

    AUTO NOTE Height RECTANGLE When AUTO is used, previously set Measuring measuring field limits (left, right and field offset) are canceled (e.g. offset is set to Width 0 mm en_BA_PosCon_OXE7.docx 38/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 39 Examples with an inclination angle of -30° The width increases when the height is reduced Examples with an inclination angle of -15° The width increases when the height is reduced en_BA_PosCon_OXE7.docx 39/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 40 Sde“ is 0. there is 0. NOTE If the measuring field is already limited with a rectangle (AUTO), the rectangle can also be changed with LIMIT L, LIMIT R, and OFFSET. en_BA_PosCon_OXE7.docx 40/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 41 250 mm - 240 mm + 10 mm = 20 mm  Entered OFFSET = 20 mm 10 mm 10 mm; offset Taught-in 10 mm Reference surface reference surface Reference point en_BA_PosCon_OXE7.docx 41/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 42 AUTO mode (green) and additional limitation LIMIT (blue) MEASURING FIELD 5.9.6 "Set maximum values" resets all adjustments of the measuring field to the standard settings (see red surface above). en_BA_PosCon_OXE7.docx 42/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 43: Digital Out

    Window point 2 (for the WINDOW mode) is selected in mm using the arrow keys. The point must be within the measuring range. The window must be > 2 mm. 5.10.5 LEVEL The output can be set to Active High or Active Low (inverted) here. en_BA_PosCon_OXE7.docx 43/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 44: System

    5.11.2 RS485 ADR In ever PosCon OXE7 sensor, this address is preset to 1 and can be changed in 3 digits. Two sensors in the same network must not have the same number, to prevent the occurrence of bus conflicts. No more than 16 sensors may be connected to one bus.

  • Page 45: Setting

    Setting 2  Setting 3 5.12.3 SHOW SHOW displays the setting values. SHOW ACTIVE Displays the active settings. SHOW SETTING 1-3 Displays the settings stored in storage spaces 1-3 en_BA_PosCon_OXE7.docx 45/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 46 MEASUREMENT TYPE EDGE HEIGHT / OBJECT HEIGHT / GAP DEPTH OBJECT PRECISION FLEX MOUNT LIMIT L LIMIT R OFFSET DIGITAL OUT WINDOW P1 (WINDOW P2) LEVEL RS485 BAUD RS485 ADR en_BA_PosCon_OXE7.docx 46/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 47: Function And Definition

    Median Average Standard Measured with standardized Baumer measuring equipment and objects. Measurement at 90% reflectivity (white) Depending on the size of the measuring field and OBJECT light/dark mode Without filter, without averaging Measured symmetrically around the reference point with 50% of the measuring field...
  • Page 48 Analog output scaling: Voltage output 0.05 V/mm 0.05 V/mm 0.1 V/mm 0.1 V/mm Current output 0.1 mA/mm 0.1 mA/mm 0.16 mA/mm 0.16 mA/mm PosCon OXE7 PosCon OXE7 PosCon OXE7 PosCon OXE7 Electrical data 11111452 11174280 11148276 11177353 OXE7.E25T-11111452 OXE7.E25T-11174280 OXE7.E25T-11148276 OXE7.E25T-11177353...
  • Page 49 PosCon OXE7 PosCon OXE7 PosCon OXE7 PosCon OXE7 Mechanical data 11111452 11174280 11148276 11177353 OXE7.E25T-11111452 OXE7.E25T-11174280 OXE7.E25T-11148276 OXE7.E25T-11177353 Width / Height / Length 26 / 74 / 55 mm 26 / 74 / 55 mm 26 / 74 / 55 mm...
  • Page 50 Optical properties PosCon OXE7 PosCon OXE7 PosCon OXE7 PosCon OXE7 11111452 11174280 11148276 11177353 OXE7.E25T-11111452 OXE7.E25T-11174280 OXE7.E25T-11148276 OXE7.E25T-11177353 Light source AlGaInP laser diode AlGaInP laser diode AlGaInP laser diode AlGaInP laser diode Wave length 656 nm 660 nm 660 nm...
  • Page 51 Beam divergence 6.1.1 Vertical level:  ⊥ Horizontal level:  ∥ en_BA_PosCon_OXE7.docx 51/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 52: Dimensions

    6.2 Dimensions *Optical axis...

  • Page 53: Mode Of Operation

    Thanks to the new Baumer qFlex technology, the position of the edge is output irrespectively of the distance between the sensor and the object to be measured. The sync input on PosCon OXE7 enables synchronization of measurement data with an object movement.
  • Page 54 Because the measuring field is exactly aligned to the housing reference surfaces at the factory, the beam position in every sensor is exactly in the same spot, which makes planning and sensor replacement very easy. en_BA_PosCon_OXE7.docx 54/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 55: Object To Be Measured

    The width of the object to be measured must not be smaller than the "smallest detectable object", and its height (step) must not be smaller than the "smallest detectable step". Right Left Width Height en_BA_PosCon_OXE7.docx 55/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 56 The average increase must be greater than ±1.5 mm at 0.5 mm. >1.5 mm 0.5 mm 0.5 mm en_BA_PosCon_OXE7.docx 56/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 57: Interfaces And Outputs

    U-Out ≈ The line resistance varies depending on the line length. In addition, the contact resistances at the plug and the ICC supply current affect the URL1 voltage drop. en_BA_PosCon_OXE7.docx 57/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 58 Ohm's law, be generated from 4...20mA with a resistance of 500Ω (parallel switching of two RM resistances of 1000Ω). That way the effect can be avoided. Power Measuring Line resistance R Sensor supply input unit +24V I-Out ≈ en_BA_PosCon_OXE7.docx 58/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 59 Function width or gap width ������������ ������������ ���� ���� = 4 ���� + ������������������ ���������� ���� ���� ∗ 0.1 ����/���� ������������ ������������ ���� �� = ������������������ ���������� ���� ���� ∗ 0.05 ��/���� en_BA_PosCon_OXE7.docx 59/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 60 If it is not possible to prevent several sensors from affecting each other through appropriate installation, the sensors can be operated asynchronously using the the Sync-In cable. The superordinate control generates the signals for this. en_BA_PosCon_OXE7.docx 60/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 61 Start of the measurement cycle High Sync-In High Laser Pulse duration Reading Camera High Find the edges Adjust the outputs High Analog Ausgang 1 measurement cycle en_BA_PosCon_OXE7.docx 61/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 62 All outputs are held (hold function). High Sync High Laser Pulse duration High Reading Camera Find the edges Adjust the outputs High Analog output Hold function en_BA_PosCon_OXE7.docx 62/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 63 If Sync-In switches from high to low level, the response time lasts takes longer in the first measurement cycle. High Sync-In 5µs High Laser Pulse duration High Reading Camera Find the edges Adjust the outputs High Analog output Measurement cycle 1 Measurement cycle 2 en_BA_PosCon_OXE7.docx 63/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 64 No more than 16 sensors may be connected to one bus during operation with RS-485. When the RS485 interface is activated, the analog output, the digital output, and the alarm output are deactivated. See separate RS 485 manual. en_BA_PosCon_OXE7.docx 64/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 65: Touch Panel

    Dimensioning 6.6.2 20.5 Capacitive operator interfaces 31.5 6.7 Memory All changes made in the sensor are saved in nonvolatile (permanent) memory and are even retained after a power outage. en_BA_PosCon_OXE7.docx 65/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 66: Safety Instructions And Maintenance

    Caution Deviation from the procedures and settings specified here can lead to hazardous radiation effects. 7.2 Sensor inscriptions Information and warning plate Approval plate Identification plate en_BA_PosCon_OXE7.docx 66/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 67 The sensor identification plate contains the following information:  Company logo  Sensor brand name  QR code for additional information  Article name and article number  Product data  Serial number: en_BA_PosCon_OXE7.docx 67/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 68: Influence Of Ambient Light

    The display and the keys must be kept free from dirt and moisture. Water and dirt on the keys can impair their function. 7.6 Disposal This sensor contains electronic components. Dispose of parts according to country-specific provisions. en_BA_PosCon_OXE7.docx 68/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 69: Error Correction And Tips

    6.64 % 22° 7.28 % 23° 7.95 % 24° 8.65 % 25° 9.37 % 26° 10.12 % 27° 10.90 % 28° 11.71 % 29° 12.54 % 30° 13.40 % en_BA_PosCon_OXE7.docx 69/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 70: The Dependency Of The Measuring Frequency

    Limitation of the measuring field with LIMIT LEFT and LIMIT RIGHT as small as possible. LIMIT RIGHT LIMIT LEFT Limitation of the measuring field (height) Limitation of the measuring field with AUTO H and OFFSET. AUTO H OFFSET en_BA_PosCon_OXE7.docx 70/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 71 The position of the limited measuring field should be in max. distance to the sensor. AUTO H OBJECT setting The OBJECT setting changes the exposure time. For a fast measurement frequency, this setting should be set to "Bright". en_BA_PosCon_OXE7.docx 71/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 72: Error Correction

    (minimum step is 2 mm)  The edges of the object do not meet the requirements of an edge, en_BA_PosCon_OXE7.docx 72/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...
  • Page 73 The edge is outside the measuring field or the measuring field was limited, see Section MEASURING FIELD Transmitting laser light is dim Sync-In input is on High--> set to Low en_BA_PosCon_OXE7.docx 73/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

  • Page 74: Revision History

    Replaced analog output curve due to an error 3/29/2017 V1.2: Implementation of the sensors 11171774 and 11174280 and some minor changes PosCon 3D changed in PosCon OXE7 10/05/2020 Added mounting advice (2.2 / 6.4.3) Added information for weak reflections (4.6.2) Added sensor influence advice sentence (6.5.3) en_BA_PosCon_OXE7.docx...
  • Page 75 75/75 Baumer Electric AG 04.01.2021 15:33/adr V1.3 ANW_81125407 Frauenfeld, Switzerland...

Table of Contents