Related Manuals for Acces I/O products 104-IDI-48 Series
Summary of Contents for Acces I/O products 104-IDI-48 Series
- Page 1 sales@artisantg.com artisantg.com (217) 352-9330 | Click HERE Find the Acces 104-IDI-48A at our website:...
- Page 2 10623 Roselle Street, San Diego, CA 92121 • (858) 550-9559 • FAX (858) 550-7322 contactus@accesio.com • www.accesio.com MODEL 104-IDI-48 SERIES USER MANUAL File: m104-idi-48.A1d...
- Page 3 ACCES, nor the rights of others. IBM PC, PC/XT, and PC/AT are registered trademarks of the International Business Machines Corporation. Printed in USA. Copyright 2006 by ACCES I/O Products Inc, 10623 Roselle Street, San Diego, CA 92121. All rights reserved. WARNING!! ALWAYS CONNECT AND DISCONNECT YOUR FIELD CABLING WITH THE COMPUTER POWER OFF.
- Page 4 Other than the above, no other warranty, expressed or implied, shall apply to any and all such equipment furnished or sold by ACCES. Manual 104-IDI-48 SERIES...
-
Page 5: Table Of Contents
Figure 3-1: Option Selection Map................11 Chapter 4: Address Selection ..................12 Table 4-1: Standard Address Assignments for Standard Computers ....12 Table 4-2: Jumper Selection Example..............13 Chapter 5: Programming .................... 14 Chapter 6: Connector Pin Assignments..............16 Manual 104-IDI-48 SERIES... -
Page 6: Chapter 1: Introduction
Letters are appended to the model numbers to signify options (described above) included on the card. Refer to Table 1-1 for model-specific information. Change-of State Interrupt MODEL No. of Bits Max Input Voltage AC Filter Capability 48AC 48BC Table 1-1: Model Versions Manual 104-IDI-48 SERIES... -
Page 7: Specification
For CE certification, isolation was specified at 60V DC or AC rms. The design intention was to eliminate the influence of common mode. Use proper wiring techniques to minimize voltage between channels and to ground. Tolerance of higher isolation voltage can be obtained on request by applying a conformal coating to the board. Manual 104-IDI-48 SERIES... - Page 8 Figure 1-1: Block Diagram Manual 104-IDI-48 SERIES...
-
Page 9: Chapter 2: Installation
START | RUN and type , click OK or press Follow the on-screen prompts to install the software for this board. LINUX Please refer to linux.htm on the CD-ROM for information on installing under linux. Manual 104-IDI-48 SERIES... - Page 10 Check that all connections in your PC/104 stack are correct and secure then power up the system. Run one of the provided sample programs appropriate for your operating system that was installed from the CD to test and validate your installation. Figure 2-1: PC/104 Key Information Manual 104-IDI-48 SERIES...
-
Page 11: Chapter 3: Option Selection
Isolated Digital Input bit changes state. A full description of how to enable/disable and clear IRQs is described in the Programming section of this manual. Refer to Figure 3-1 for more on filter and interrupt selection. Manual 104-IDI-48 SERIES... - Page 12 Figure 3-1: Option Selection Map Manual 104-IDI-48 SERIES...
-
Page 13: Chapter 4: Address Selection
SETUP program provided with the board. If you prefer to determine proper jumper settings yourself, first convert the hex-code address to binary form. Then, for each “0”, install corresponding jumpers and for each “1” remove the corresponding jumper. Manual 104-IDI-48 SERIES... - Page 14 The following example illustrates jumper selection corresponding to hex 300 (or binary 11 0000 0xxx). The “xxx” represents address lines A2, A1, and A0. Base Address in Hex Code Conversion Factors Binary Representation Jumper Legend Address Line Controlled Jumper Selection Table 4-2: Jumper Selection Example Manual 104-IDI-48 SERIES...
-
Page 15: Chapter 5: Programming
Base + 7 refer to the “Read Base + 7” table. Please note: Enabling or Disabling IRQs does not clear the IRQ latch. If you disable IRQs while one is pending, it is still required to read from Base + 7 to clear the pending IRQ. Manual 104-IDI-48 SERIES... - Page 16 Port 1 Low Port 0 Port 0 Mid Port 0 Low High Byte Byte Byte IRQ High Byte Byte IRQ Byte Enable / Enable / Enable / Enable / Disable Enable / Disable Enable / Disable Disable Disable Disable Manual 104-IDI-48 SERIES...
-
Page 17: Chapter 6: Connector Pin Assignments
Bit 17 B Bit 18 A Bit 18 B Bit 19 A Bit 19 B Bit 20 A Bit 20 B Bit 21 A Bit 21 B Bit 22 A Bit 22 B Bit 23 A Bit 23 B Manual 104-IDI-48 SERIES... - Page 18 If you experience any problems with this manual or just want to give us some feedback, please email us at: manuals@accesio.com. Please detail any errors you find and include your mailing address so that we can send you any manual updates. 10623 Roselle Street, San Diego CA 92121 Tel. (858)550-9559 FAX (858)550-7322 www.accesio.com Manual 104-IDI-48 SERIES...
Need help?
Do you have a question about the 104-IDI-48 Series and is the answer not in the manual?
Questions and answers