Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Idex FAST&FLUID SK300 CE
- Page 1 Manual SK300 CE V. 1.0 Fast & Fluid Management B. V. www.fast-fluid.com...
- Page 2 © Fast & Fluid Management B.V. This manual or parts thereof may not be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, nor otherwise, without the prior written permission of Fast & Fluid Management B.V.
-
Page 3: Table Of Contents
SK300 CE Table of Contents V. 1.0 Table of Contents About this manual ......................5 How to work with the manual .................... 5 Record of changes ......................5 Safety ..........................6 Intended use ........................6 Liability ..........................6 2.2.1 General liability ..................... 6 2.2.2 Machine-specific liability .................. - Page 4 SK300 CE Table of Contents V. 1.0 4.1.2 Remove the plastic foil ..................16 4.1.3 Unlock the machine .................... 17 4.1.4 Remove the wooden blocks ................17 4.1.5 Remove the transport brackets ................18 4.1.6 Dispose of the packaging material ..............18 Put the machine in position.....................
-
Page 5: About This Manual
SK300 CE About this manual V. 1.0 About this manual The manual shows the information necessary to: install operate perform basic maintenance correct small problems The SK300 and all its versions are referred to in the manual as the 'machine'. This manual contains the original instructions. -
Page 6: Safety
Safety SK300 CE V. 1.0 Safety WARNlNG Read the manual before you install or use the machine. Failure to do so can result in personal injury, death or property damage. lntended use The machine is designed to shake colorants in a can. Any other use of the machine is strictly forbidden. Liability 2.2.1 General liability... -
Page 7: User Qualification For Installation
Safety SK300 CE V. 1.0 Personal harm should be avoided by strictly following the materials safety data sheets (MSDS) for colorants and (base) paint. The use of flammable colorants or colorants that diffuse potential explosive vapors may present fire and explosion risks. -
Page 8: Safety Symbols In The Manual
Safety SK300 CE V. 1.0 Safety symbols in the manual WARNlNG Note Can cause personal injury. Shows further information. CAUTlON Can cause damage to the machine. Disposal of the machine 1. Sort the machine, the accessories and the packaging for environmentally friendly recycling. -
Page 9: Operator Manual
Operator manual SK300 CE V. 1.0 Operator manual Description 3.1.1 Overview of the machine On/off switch Can handle retainer Net entry Wheels Type plate. See also § 3.1.5. Adjustable feet Spindle Can table Door Can plate Lid padding Control panel. See also § 3.1.2. -
Page 10: Overview Of The Control Panel
Operator manual SK300 CE V. 1.0 3.1.2 Overview of the control panel Emergency stop switch Display Stop/up key Start keys 3.1.3 Factory default shake times Note The display shows the factory default shake times. Each start key has a default time. You can combine the different shake times by selecting multiple start keys. -
Page 11: Type Plate: Details
Operator manual SK300 CE V. 1.0 3.1.5 Type plate: details Operation WARNlNG Only push the emergency stop switch in the case of a safety emergency. Make sure that the problem is solved before you reset the emergency stop switch. 3.2.1 Turning on the machine 1. -
Page 12: Placing The Can
Operator manual SK300 CE V. 1.0 3.2.4 Placing the can Open the doors 1. Open the doors (A). Use the handle (B). Place the can 1. Put one or more cans (A) in the centre of the can table, or in a pattern that has its gravitational centre in the middle of the can table. -
Page 13: Start The Machine
Operator manual SK300 CE V. 1.0 Retain the can handle 1. If you place one can, make sure that the can handle (A) cannot move. Use the can handle retainer (B). 2. If you place more than one can at the same time, make sure that the can handles cannot move. -
Page 14: Remove The Can
Operator manual SK300 CE V. 1.0 Note The display shows the selected shake time. 3.2.6 Remove the can 1. Make sure that the machine is ready. Note The door will unlock after shaking when the display shows 'rdY'. 2. Open the doors (A). Use the handle (B). 3. -
Page 15: Restart The Machine
Operator manual SK300 CE V. 1.0 3.2.9 Restart the machine 1. Set the on/off switch to the off position. 2. Wait 30 seconds. 3. Turn on the machine. See § 3.2.1. Maintenance 3.3.1 General safety instructions for maintenance WARNlNG Check the MSDS of the colorants about personal protection measures required for handling the colorant. -
Page 16: Lnstallation
lnstallation SK300 CE V. 1.0 lnstallation Unpack the machine 4.1.1 Remove the cardboard 1. Remove the cardboard (A). 4.1.2 Remove the plastic foil 1. Remove the plastic foil (A). -
Page 17: Unlock The Machine
lnstallation SK300 CE V. 1.0 4.1.3 Unlock the machine 1. Remove the bolts (A) at both sides of the machine. The wooden blocks (B) are now free to move. 4.1.4 Remove the wooden blocks CAUTlON If you do not remove all loose parts, this can cause severe damage to the machine when it is in operation. -
Page 18: Remove The Transport Brackets
lnstallation SK300 CE V. 1.0 4.1.5 Remove the transport brackets 1. Remove the screws (A). 17mm 2. Remove the transport brackets (B). 4.1.6 Dispose of the packaging material 1. Dispose of the packaging material in an environmentally friendly way, according to local regulations, see § 2.7. Put the machine in position 4.2.1 Move the machine from the pallet... -
Page 19: Level The Machine
lnstallation SK300 CE V. 1.0 WARNlNG Mind the minimum requirement of the load capacity of the floor. See § 6.2. Note Make sure the final location is well-lit and well- ventilated. 1. Push the machine to the final location. 2. Connect the power cable to the net entry. 3. -
Page 20: Troubleshooting
Troubleshooting V. 1.0 SK300 CE Troubleshooting General troubleshooting procedure 1. Try to solve the problem with the information in this manual. See § 5.3. 2. If it is not possible to solve the problem with the information in this manual, contact service. See § 5.2. Contact service 1. -
Page 21: Technical Data
SK300 CE Technical data V. 1.0 Technical data General specifications Parameter Specification Materials used are suitable for Water, universal and solvent colorants Maximum load weight [kg] Can table dimensions [cm] 36 x 35 Maximum can height [cm] Minimum can height [cm] Maximum shake speed [rpm] Maximum shake time [sec] 9999... -
Page 22: Safety Classifications
SK300 CE Technical data V. 1.0 Safety classifications Parameter Specification IP (Ingress Protection) classification EMC (ElectroMagnetic Compliancy) classification Class B Overvoltage category Class II Electrical specifications Parameter Specification Power consumption, maximum [W] Maximum leakage current [mA] Country specific net cables European Voltage [V] Frequency [Hz]... -
Page 23: Electrical Diagram
SK300 CE Technical data V. 1.0 Electrical diagram...