Page 4
Use of other accessories may not ensure compliance with FCC RF exposure guidelines. European Conformity Statement unitech Electronics co., Ltd herewith declares that the unitech product is in compliance with the essential requirements and all other provisions of the RED 2014/53/EU directive.
Page 6
Waste electrical and electronic equipment (WEEE) unitech has set up a policy and process to meet the 2012/19/EU concerning electronic waste disposal. For more detailed information of the electronic waste disposal of the products you have purchased from unitech directly or via unitech’s resellers, you shall either...
Page 8
Laser Information The unitech product is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 60825-1. Class II and Class 2 products are not considered to be hazardous. The unitech product contains internally a Visible Laser Diode (VLD) whose emissions do not exceed the maximum limits as set forth in the above regulations.
Page 10
It may not be functional anymore. Please only use the original battery from unitech. Using a third party battery can damage our products. Please note that when such damage occurs, it is not covered by unitech’s warranty policy.
Page 12
Please remove the power adapter when the battery is fully recharged. The bundled power adapter that comes with your unitech product is not meant to be used outdoors. An adapter exposed to water or rain, or a very humid environment can cause damage to both the adapter and the product.
Page 14
Worldwide Support unitech’s professional support team is available to quickly answer questions or assist with technical-related issues. Should an equipment problem occur, please contact the nearest unitech regional service representative. For complete contact information please visit the Web sites listed below: Taipei, Taiwan –...
Page 15
The warranty period is varied from each country. Please consult with your supplier or unitech local office for actual length of warranty period to your purchased product. Warranty becomes void if equipment is modified, improperly installed or used, damaged by accident or neglect, or if any parts are improperly installed or replaced by the user.
WD200 User’s Manual Chapter 1 - Overview 1.1 Package Please make sure the following contents are in the WD200 gift box. If something is missing or damaged, please contact your unitech representative. The basic package contents WD200 USB 3.0 Type C Cable Quick Start Guide ...
1.4 Getting Started 1.4.1 Charging the Battery Connect the USB cable to the USB port on WD200 and connect the other end to an AC power adapter. We recommend only the USB cable that comes with the WD200, or a unitech designed cradle, to charge the WD200.
Page 24
WD200 User’s Manual 1.4.3 Turning on the terminal for the first time It is recommended to fully charge WD200 before first use. You can now start up your device to set up the languages, WLAN setting, and date and time.
Page 25
WD200 User’s Manual 1.4.5 Using the Nano SIM Card The WD200 has 1 x nano SIM card slot. Remove the one screw on the Nano SIM card slot cover with a Screwdriver. Remove the cover. Insert the SIM card. Push the card into the slot until you feel the card click into place.
Page 27
WD200 User’s Manual Make sure that both devices are unlocked and have NFC turned on. Also make sure that the NFC antenna area of WD200 and the other devices' NFC area are close to one another. Slightly moving the device until a connection is made.
WD200 User’s Manual 2.5 PC Setting Connect WD200 to your computer with the USB type C cable. Your computer will recognize it is USB charging. Slide down from top, the system will show as follow picture, then you can select File transfers.
WD200 User’s Manual 2.9 KeyRemap The WD200’s keys can be programmed for users to be able to perform different functions or applications. Two options to use key remap functions : CAMERA and RECENT. Camera Recent Virtual Button 2.9.1 Remap a key On the main screen, scroll the screen from down to top to reach the APPS, and KeyRemap.
WD200 User’s Manual 3.3 StageGO StageGO is a configuration staging solution for unitech mobile devices. StageGO helps IT admins to use the 1-click auto configure feature to set up and initialize a device quickly. Devices configure themselves by using configuration scripts and barcodes prepared by the IT admins, the StageGO app, currently available for Android devices, uses unitech devices’...
WD200 User’s Manual 3.4 MoboLink MoboLink is a software platform that helps unitech customers to remote manage their purchased devices and applications. The core of the MoboLink platform provides functionalities in the MDM (Mobile Device Management) and MAM (Mobile Application Management) domains, and then further extends into other management functions such as alert notification management and account management.
Need help?
Do you have a question about the WD200 and is the answer not in the manual?
Questions and answers