Page 6
("SAR") des limites lorsqu'il est utilisé dans des conditions d'exposition portatifs. European Conformity Statement Unitech Electronics co., Ltd herewith declares that the Unitech product is in compliance with the essential requirements and all other provisions of the RED 2014/53/EU directive.
Waste electrical and electronic equipment (WEEE) Unitech has set up a policy and process to meet the 2012/19/EU concerning electronic waste disposal. For more detailed information of the electronic waste disposal of the products you have purchased from Unitech directly or via Unitech’s resellers, you shall either...
Laser Information The Unitech product is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 60825-1. Class II and Class 2 products are not considered to be hazardous. The Unitech product contains internally a Visible Laser Diode (VLD) whose emissions do not exceed the maximum limits as set forth in the above regulations.
Unitech product for charging. Please remove the power adapter when the battery is fully recharged. The bundled power adapter that comes with your Unitech product is not meant to be used outdoors. An adapter exposed to water or rain, or a very humid environment can cause damage to both the adapter and the product.
Worldwide Support Unitech’s professional support team is available to quickly answer questions or assist with technical-related issues. Should an equipment problem occur, please contact the nearest Unitech regional service representative. For complete contact information please visit the Web sites listed below: Taipei, Taiwan –...
The warranty period is varied from each country. Please consult with your supplier or Unitech local office for actual length of warranty period to your purchased product. Warranty becomes void if equipment is modified, improperly installed or used, damaged by accident or neglect, or if any parts are improperly installed or replaced by the user.
HT730 (38 keys) User’s Manual Chapter 1 - Overview 1.1 Package Please make sure the following contents are in the HT730 gift box. If something is missing or damaged, please contact your Unitech representative. The basic package contents HT730 ...
It is highly recommended that using the Unitech USB Type-C cable and AC power adapter to charge the terminal. The charging LED indicator on HT730 is turning red when it is in charging state. The green light is on after the battery is fully charged.
HT730 (38 keys) User’s Manual 1.4.4 Turning on the terminal for the first time It is recommended to fully charge HT730 before first use. You can now start up your device to set up the languages, WLAN setting, and date and time.
Page 33
HT730 (38 keys) User’s Manual 1.4.6 Using the Micro SD / Nano SIM Card The HT730 has 1 x micro SD and 2 x nano SIM card slots inside the battery compartment. Note: Please TURN OFF the terminal, before inserting or removing micro SD card or...
Page 41
HT730 (38 keys) User’s Manual 1.5.1 How to Pull Up the Soft Keypad on HT730 When there is a number or text to be entered, pressing the P1 key will pop up the SIP (Soft Input Panel) keyboard on the screen, and when you press the P1 key again, the SIP keyboard will disappear.
Page 50
HT730 (38 keys) User’s Manual Make sure that both devices are unlocked and have NFC turned on. Also make sure that the NFC antenna area of HT730 and the other devices' NFC area are close to one another. Slightly moving the phones until a connection is made.
HT730 (38 keys) User’s Manual 2.7 PC Setting Connect HT730 to your computer with the USB type C cable. Your computer will recognize it is USB charging. Slide down from top, the system will show as follow picture, then you can select File transfers.
HT730 (38 keys) User’s Manual 2.11 KeyRemap The HT730’s keys can be programmed for users to be able to perform different functions or applications. Six options to use key remap functions : SCAN_LEFT, SCAN_RIGHT, SCAN_KEY, PROG_1, PROG_2 and TRIGGER_GUN 2.12.1 Remap a key On the main screen, scroll the screen from down to top to reach the APPS, and KeyRemap.
HT730 (38 keys) User’s Manual 3.1.3 Picklist Mode Picklist mode enables HT730 to decode only barcodes that are aligned under the laser crosshair or LED aiming dot. For picklist mode demonstration, please click on the Unitech youtube channel for more information : https://www.youtube.com/watch?v=QjT2E6hxD_k...
HT730 (38 keys) User’s Manual 3.4 StageGO StageGO is a configuration staging solution for Unitech mobile devices. StageGO helps IT admins to use the 1-click auto configure feature to set up and initialize a device quickly. Devices configure themselves by using configuration scripts and barcodes prepared by the IT admins, the StageGO app, currently available for Android devices, uses Unitech devices’...
HT730 (38 keys) User’s Manual 3.5 MoboLink MoboLink is a software platform that helps Unitech customers to remote manage their purchased devices and applications. The core of the MoboLink platform provides functionalities in the MDM (Mobile Device Management) and MAM (Mobile Application Management) domains, and then further extends into other management functions such as alert notification management and account management.
Need help?
Do you have a question about the HT730 and is the answer not in the manual?
Questions and answers