Inserting The Drip Tray / Drip Tray Grid; First Use / Bleeding; Making Espresso - Profi Cook PC-ES 1209 Instruction Manual

Inserting the Drip Tray / Drip Tray Grid

• Insert the container for the residual water, with the
float (8) inserted, into the compartment (6).
• Place the drip tray grid onto the compartment as a cover.

First Use / Bleeding

CAUTION:
Bleed the appliance before first use and after a longer
period of non-use. Do not use coffee grounds during this
process!
1. Fill the water tank with clean, fresh water to the MAX
marking. Close the lid again.
2. Set the filter holder.
3. Switch the appliance on. The operating control lamp
lights up. The appliance starts heating up. The warming
plate heats up.
4. Set a suitable bowl (heat-resistant / approx. 500 ml)
under the brewing head.
5. Make sure that the steam pressure switch
gaged.
6. As soon as the control lamp
pump with the pressure switch
Let 2 to 3 cups run through. To empty the container
in the meantime, switch off the pump. Disengage the
pressure switch before doing so.
WARNING: Risk of burns!
The water inside the bowl is hot.
7. Swing the steam nozzle outwards. Make sure that the
steam tube is attached.
8. Empty the bowl and set it under the steam nozzle.
9. Lock the steam pressure switch
the heating process for steam generation has ended.
To do this, please consult the scale on the temperature
display.
10.
WARNING: Risk of burns!
Hot steam escapes from the steam nozzle.
To generate steam, set the steam control knob to the
MAX position. Turn off the pump after water is evenly
emitted from the steam nozzle. Set the rotary switch to
the OFF position (off).
WARNING: Risk of burns!
• In case you want to move the steam nozzle after
the steaming process, always hold it by the black
rubber handle!
• The water inside the bowl is hot.
11. The appliance now is vented and ready for operation.
PC-ES1209_IM_new

Making Espresso

Do not brew an espresso when the appliance is still under
pressure (for example when milk has been frothed ear-
lier). With too much pressure in the appliance, espresso
leaks at the edge of the brewing head. That may lead to a
faster wearing of the rubber seal.
1. Switch the appliance on. The operating control lamp
2. Fill the water tank with the desired amount of clean,
3. If you frothed milk earlier, completely release the pres-
is disen-
lights up, start the
. The water flow starts.
4. Select a filter insert (20 / 21). Place the insert in the filter
5. Fill the filter insert with espresso grounds. Use the
into place. Wait until
6. Attach the filter holder to the group head. Ensure that
7. The necessary brewing temperature is reached as soon
8. Press the pressure switch
9. Stop the brewing process by turning off the pump when
10. Remove the cup(s).
CAUTION:
lights up. The appliance starts heating up. The warming
plate heats up.
NOTE:
• Use the warming plate to pre-heat your cup(s).
• If you want to pre-heat the cup(s) more rapidly,
rinse them with hot water.
fresh water. The water level must be between the MIN
and MAX markings. Close the lid again.
sure from the appliance:
3.1. Make sure that the pressure switch for the steam
is disengaged and the steam control knob is set to
OFF.
3.2. Set a suitable vessel under the steam nozzle.
3.3. Set the steam control knob to the MAX position
until no more steam comes out.
3.4. Turn the steam control knob back to the OFF posi-
tion.
holder. Ensure that the filter safeguard is not upright.
measuring spoon provided (one measuring spoon
filling = 1 cup). Spread the espresso grounds evenly and
push down slightly with the tamper. Clean the edge of
the filter holder.
the filter holder is properly attached in the group head.
as the indicator lamp lights up. Place your cup(s)
under the brewing head exactly on the two holes that
you can see in the draining rack.
to lock it into place. The
hot water is forced through the filter.
NOTE:
This process does not end automatically!
the desired amount of espresso is in your cup(s): Press
the pressure switch again to release it.
NOTE:
Remove the filter holder every time after making es-
presso. In this way you extend the lifetime of the group
head's rubber seal.
59
17.08.20