Exmark LAZER Z ULTRA VAC QDS Setup Instructions
Hide thumbs
Also See for LAZER Z ULTRA VAC QDS:
- Operator's manual (32 pages) ,
- Operator's manual (32 pages)
Advertisement
Quick Links
Models and Required Completing Kits
Note: Use the chart below to verify the kits required for the unit.
UNIT
Lazer Z 604
(Includes AS)
Lazer Z 604
(Includes AS)
Lazer Z XS 604
Lazer Z XP 604
Lazer Z 724
Lazer Z 724
Lazer Z XS 724
Lazer Z XP 724
Lazer Z 605 Triton
Lazer Z XS Air Cooled
605 Triton
Lazer Z XS Liquid Cooled
605 Triton
Lazer Z 665 Triton
Lazer Z XS Air Cooled
665 Triton
Lazer Z XS Liquid Cooled
665 Triton
Lazer Z 725 Triton
Lazer Z XS Air Cooled
725 Triton
Lazer Z XS Liquid Cooled
725 Triton
*Units with a 2-post foldable ROPS installed will also require use of 103-5633 Front Weight Kit
Model Numbers
UVD60 – Fits Lazer Z, Lazer Z XP, and Lazer Z XS with 60" deck
UVD6672 – Fits Lazer Z, Lazer XP, and Lazer Z XS with 66" or 72" deck
LAZER Z
SERIAL NUMBER
REQ'D TO MOUNT ULTRA VAC
510,000 & Higher
352,000 to 509,999
440,000 to 599,999
352,000 to 599,999
510,000 & Higher
352,000 to 509,999
440,000 to 599,999
352,000 to 599,999
600,000 & Higher
600,000 & Higher
600,000 & Higher
600,000 & Higher
600,000 & Higher
600,000 & Higher
600,000 & Higher
600,000 & Higher
600,000 & Higher
®
ULTRA VAC QDS
SETUP INSTRUCTIONS
For Serial Nos. 600,000 and Higher
109-1179 Drive Kit and
103-5633 Front Weight Kit
109-1189 Drive Kit*
109-1193 Drive Kit and
103-5633 Front Weight Kit
109-1193 Drive Kit*
109-1194 Drive Kit and
103-5633 Front Weight Kit
109-1191 Drive Kit*
109-1194 Drive Kit and
103-5633 Front Weight Kit
109-1194 Drive Kit*
109-1167 Drive Kit
109-1167 Drive Kit
109-1167 Drive Kit and
109-2203 Floor Pan Weight
109-1168 Drive Kit
109-1168 Drive Kit
109-1168 Drive Kit and
109-2203 Floor Pan Weight
109-1169 Drive Kit
109-1169 Drive Kit
109-1169 Drive Kit and
109-2203 Floor Pan Weight
Page 1 of 13
109-4195 Rev. A
Advertisement
Related Manuals for Exmark LAZER Z ULTRA VAC QDS
Summary of Contents for Exmark LAZER Z ULTRA VAC QDS
- Page 1 ® LAZER Z ULTRA VAC QDS SETUP INSTRUCTIONS For Serial Nos. 600,000 and Higher Models and Required Completing Kits Note: Use the chart below to verify the kits required for the unit. UNIT SERIAL NUMBER REQ'D TO MOUNT ULTRA VAC Lazer Z 604 109-1179 Drive Kit and 510,000 &...
- Page 2 1. Assembly Instructions Item Description Hopper Assembly Upper Tube Lower Tube #10-24 CRPH Screw #10-24 Nyloc Nut #10 Flat Washer Handle Assembly Blower Assembly Bagger Mount Weldment Belt Cover Caster Weight Jackshaft Blower Drive Belt Frame Bracket RH Frame Bracket LH Frame Bracket Mount Spacer Mount Pin Weldment...
- Page 3 ALL LAZER Z XP & LAZER Z XS AND LAZER Z SN 510,000 & HIGHER (Shown without ROPS for clarity) LAZER Z SN 352,000-509,999 ASSEMBLY DIAGRAM (Shown without ROPS for clarity) FIGURE 1 Page 3 of 13 109-4195 Rev. A...
- Page 4 For Lazer Z XP Lazer Z XS units: Safety 5. Install mount weldment (Item 9) loosely to the Safety Alert Symbol rear bumper using the two holes provided. Secure using (2) 3/8-16 x 1.00 screws (Item This SAFETY ALERT SYMBOL is used 23), (2) 3/8 spring disk washers (Item 25) and both in this instruction sheet and on the machine...
- Page 5 CAUTION POTENTIAL HAZARD ♦ Relying solely on mechanical or hydraulic jacks to support the mower could be dangerous. WHAT CAN HAPPEN ♦ The mechanical or hydraulic jacks may not be enough support or may malfunction allowing the unit to fall, which could cause injury. HOW TO AVOID THE HAZARD ♦...
- Page 6 Units without ROPS skip to Step 28: 14. Align three spacers (Item 45) on each side and tape with masking tape to the rear frame as shown in Figure 5. 15. Align lower roll bar tubes along wheel motor channels as shown in Figure 5. 16.
- Page 7 sure that the raised portion of the spring disk washer faces the head of the bolt. (See Figure 7) FIGURE 6 All units: 28. Tighten all hardware that attaches the Ultra Vac mount to the machine frame. Start with the screws that hold the mount weldment to the rear of the unit and work forward.
- Page 8 Units SN 600,000 and Lower With Splined Installation of Blower Assembly Blade Driver: Units SN 352,000-509,999 without splined blade 9. Lower the deck fully. Remove the right hand driver: belt cover. Remove the belt cover mounting 1. Lower the deck fully. Remove the right hand belt stud that protrudes from the deck.
- Page 9 16. Reinstall the deck drive belt in the lower groove of 23. Reinstall the deck drive belt in the lower the double sheave. Install plug (Item 40) into grove of the double sheave. Install plug bore of double sheave. (Item 40) into bore of top sheave. 17.
- Page 10 mounting pin. The mount pin can be installed in 30. Pull the spring loaded idler back and slip the two positions. For 60” decks, SN 599,999 and belt over the top deck spindle sheave. lower, the pin should be installed as far away from 31.
- Page 11 mounted position). Align the bottom edge of the weight plate with the bottom edge of the floor 3. Set deck in lowest cutting position. pan front panel. Center the weight plate side to 4. Slide lower tube onto blower and latch (make sure side.
- Page 12 Note: The removable weight is heavy. Use (Items 34, 35, and 36). The weight plates will care when lifting. Make sure that you can hold only fit with the ears located near the bend in the weight securely before lifting. Use caution the floor pan (See Figure 17).
-
Page 13: Operation
Operation Pre-Start 1. Read the operator’s manual for the mower and Ultra Vac to familiarize yourself with all controls before operating the machine. Make sure that you understand the controls, their locations, their functions, and their safety requirements. 2. Ensure the blower, belt cover, bags, tube and hood are in good condition, properly attached, and latched.