Exmark LAZER Z HP ULTRA VAC QDS Setup Instructions
Hide thumbs
Also See for LAZER Z HP ULTRA VAC QDS:
- Operator's manual (24 pages) ,
- Operator's manual (24 pages)
Advertisement
Quick Links
Models and Required Completing Kits
Note: Use the chart below to verify the kits required for the unit.
LHPUVD4448
44" Deck
All Serial Numbers
48" Deck
SN 203376 & Higher
LHPUVD4650
46" Deck
All Serial Numbers
50" Deck
All Serial Numbers
LHPUVD5256
52" Deck
All Serial Numbers
*Front weight Kit 103-5629 is required on any unit with a 2 post ROPS installed.
56" Deck
All Serial Numbers
®
LAZER Z
HP ULTRA VAC QDS
SETUP INSTRUCTIONS
Drive Kit
103-1315
Drive Kit
103-1314
Drive Kit
109-1013
Drive Kit
109-1014
Drive Kit
109-1185
Drive Kit
109-1015
For Serial Nos. 600,000 and Higher
Page 1 of 10
109-3288 Rev. B
Advertisement
Related Manuals for Exmark LAZER Z HP ULTRA VAC QDS
Summary of Contents for Exmark LAZER Z HP ULTRA VAC QDS
- Page 1 ® LAZER Z HP ULTRA VAC QDS SETUP INSTRUCTIONS For Serial Nos. 600,000 and Higher Models and Required Completing Kits Note: Use the chart below to verify the kits required for the unit. LHPUVD4448 44” Deck Drive Kit All Serial Numbers 103-1315 48”...
- Page 2 1. Assembly Instructions Description Description Engine Guard 44, 46, 48, 50 units #10 Flat Washer Bagger Mount Weldment #10 – 24 Nyloc Nut 5/16 – 18 X 1.00 Hex Head Screw Blower Assembly Hopper Assembly Rear Weight 52 and 56 units Hair Pin Spacer 52 and 56 units Upper Tube...
- Page 3 Ultra Vac Drive Kit Ultra Vac Weight Kit Key Qty Description (units with 2 post ROPS only) 1 Spacer, Counterweight (52” and 56” decks) Key Qty Description (See Figure 1) 2 Asm, Weight 1 Pin, Chute Pivot 1 Plate, Weight Mounting 1 Pin, Hair 4 5/16-18 x 1 Hex Head Screw 1 Chute Weldment (48”...
- Page 4 Safety Blower Drive Sheave Installation Safety Alert Symbol Units Below 510,000 Without Splined Blade Driver 1. Stop engine, remove key, and wait for all This SAFETY ALERT SYMBOL is used moving parts to stop. both in this instruction sheet and on the machine to identify important safety messages which must 2.
- Page 5 9. Install 5/16-18 x .62 screw (Item 26) into hole Units Below 600,000 With Splined Blade that 5/16 – 18 x 3 ¼ bolt was removed from Driver on the deck. Use the whizlock nut removed in 1. Stop engine, remove key, and wait for all step 2).
- Page 6 10. Reinstall the deck drive belt in the lower groove Units 600,000 And Higher of the double sheave. Install plug (Item 27) into 1. Stop engine, remove key, and wait for all bore of double sheave. moving parts to stop. 11.
-
Page 7: Install Weight Assembly
drill 3/8” upper mounting holes in the front Install Weight Assembly panel of the floorpan. 1. Remove the hardware from the front of the floor 3. Permanently mount the weight mounting plate pan. Discard the screws and retain the washer to the front panel of the floor pan using (4) and whizlock nuts. - Page 8 3. Install the Rear Weight (Item 12) and spacer (Item of the right hand arm. Position the arms so 13) from the drive kit using the (8) 5/16 – 18 that their ends are the same distance from the X1.75 screws (Item 14) and whizlock nuts upper frame tube.
-
Page 9: Assemble Tubes
FIGURE 10 5. Slide lower tube (Item 7) onto blower (Item 11) Assemble Tubes and latch (make sure that upper tube does not 1. Slip upper and lower tubes together (Items 6 and 7). move out of alignment). 2. Insert upper tube (Item 6) into hopper seal (Item 4) 6. - Page 10 Install Blower Assembly WARNING 1. Remove the belt guide on the blower (Item 11). (See Figure 13) POTENTIAL HAZARD ♦ 2. Install the belt (from the Drive Kit – Item 24) onto the If the blower intake opening is not correct it Blower Assembly (Item 11) as shown.