Programming Example - Emerson Dosaodor-D V

DAILY DIAGNOSTIC
Daily event type list. The codes are visible only on the
remote control software DosaLink.
CODE DIAGNOSTIC DESCRIPTION
0 DOSAODOR RUNNING
1 DOSAODOR MANUAL
2 DOSAODOR EXCLUDED
4 DOSAODOR WASHING
8 ALARM COMMUNICATION BOARD"
16 ALARM ODORANT RELOADING
32 ALARM GAS FLOW COMPUTER
64 ALARM HI GAS FLOW RATE
128 ALARM INJECT.N. - 1
256 ALARM INJECT.N. - 2
512 ALARM ANALOG INPUT
1024 DOSAODOR RESET
2048 ACTUAL ALARM RESET
4096 TOTALIZER RESET
8192 MEMORY DATA RESET
16384 ALARM PRINTER ERROR
32768 MEMORY EVENT RESET
65536 POWER SUPPLY ON
131072 POWER SUPPLY OFF
262144 ALARM LOW ODORANT LEVEL
524288 ALARM HF PULSE INPUT
1048576 ALARM LOW Q - START
2097152 ALARM LOW Q - STOP
4194304 ALL. GAS COMPRESSOR UNIT
8388608 DOSAODOR MASTER - SET
16777216 DOSAODOR SLAVE - SET
33554432 DOSAODOR SLAVE - WAITING"
67108864 DOSAODOR SLAVE - START
134217728 BEGIN 220V ALARM
268435456 END 220V ALARM
c) 3) PRINTING Event Report
By pressing the "3" key, the event report is printed. This
report records the last 30 operations/alarms occurred in
the system, completed with Date and Time. These are
the possible messages:
DATE TIME EVENT -
xx/xx/xx xx:xx DOSAODOR EXCLUDED
xx/xx/xx xx:xx DOSAODOR RUNNING
xx/xx/xx xx:xx DOSAODOR MANUAL
xx/xx/xx xx:xx DOSAODOR WASHING
xx/xx/xx xx:xx ACTUAL ALARM RESET
xx/xx/xx xx:xx TOTALIZER RESET
xx/xx/xx xx:xx MEMORY DATA RESET
xx/xx/xx xx:xx ALARM INJECT. N. 1
xx/xx/xx xx:xx ALARM INJECT. N. 2
xx/xx/xx xx:xx ALARM ODORANT RELOADING
xx/xx/xx xx:xx ALARM HI GAS FLOWRATE
xx/xx/xx xx:xx ALARM GAS FLOW COMPUTER
xx/xx/xx xx:xx ALARM ANALOG INPUT
xx/xx/xx xx:xx ALARM LOW ODORANT LEVEL
xx/xx/xx xx:xx ALARM COMUNICATION BOARD
xx/xx/xx xx:xx ALARM PRINTER ERROR
xx/xx/xx xx:xx ALARM HF PULSE INPUT
xx/xx/xx xx:xx Q = 0 EMERGENCY SYS. ON
xx/xx/xx xx:xx Q > 0 EMERGENCY SYS. OFF
xx/xx/xx xx:xx POWER SUPPLY ON
xx/xx/xx xx:xx POWER SUPPLY OFF
xx/xx/xx xx:xx ALL. GAS COMPRESSOR UNIT
xx/xx/xx xx:xx DOSAODOR MASTER – SET
xx/xx/xx xx:xx DOSAODOR SLAVE – SET
xx/xx/xx xx:xx DOSAODOR SLAVE – WAITING
xx/xx/xx xx:xx DOSAODOR SLAVE – START

Programming Example

The following represents an example for programming
including explanatory notes. See paragraph "Programming
Sequence" (Pag. 26) for an explanation of how to enter and
modify data.
Loc:00
a) Language Messages
Press Enter until the message REQUIRED appears.
b) Date Day/Month/Year (Month/Day/Year)
Enter the current date in the format Day/Month/
Year (Month/Day/Year if you are selected ENG.U.S.
Language)
c) Time Hour/Minute/Second
Enter the current date in the format Hour/Minute/Second
Loc:01
a) Odorant rate Prog. mg/
Enter the odorant concentration value to be kept
approximately.
40 mg/m 3 (2.490 lb/MMCF) in case of THT
10 mg/m (0.622 lb/MMCF) in case of Mercaptan
3
7 mg/ m 3 (0.436 lb/MMCF) in case of Spotleak 2323
b) Gas Volume input – 1 Pulse =
(provided that Gas Volume is detected through Pulse input)
Enter the "weight" of the input pulse, representing the
number of Sm 3 (MCF) correspond to one received pulse.
WARNING
!
The Dosaodor‑D control unit can detect
pulse signals without voltage (ON/OFF) with
a frequency no higher than 1 Hz (one pulse/
second). Therefore it is necessary to check
the programming of the flow computer.
Volumetric Measure
(with meter connected to BF sender)
Follow the parameters below to calculate the "weight" of
the pulse:
• BF pulse weight of the Biggest Meter
[1 pulse = m 3 ] = Pulse ON
• (BF pulse weight of the Biggest Meter
[1 pulse = MCF] = Pulse ON)
• Max. measured gas pressure [bar] (PSIG) = Pmax
• C = (Pulse IN x (Pmax + 1)) * 1.2
Dosaodor-D
(lb/MMCF)
m
3
(1 Pulse = MCF)
m 3
31