Advertisement
Quick Links
BEFORE YOU START PLEASE READ INSTRUCTIONS CAREFULLY
TIMBER
BUILDING A BASE
TYPES OF BASE
Whilst all products manufactured are made to the highest standards of Safety and in
the case of childrens products independently tested to EN71 level, we cannot accept
responsibility for your safety whilst erecting or using this product.
Refer to the instructions pages for your speci c product code
MUST
2mm Drill bit
NOT
For assistance please contact customer care on: 01636 821215
Mercia Garden Products Limited,
Sutton On Trent,
Newark,
Nottinghamshire,
NG23 6QN
www.merciagardenproducts.co.uk
CAUTION
Advertisement
Related Manuals for Mercia Garden Products 0619LOG003-V5
Summary of Contents for Mercia Garden Products 0619LOG003-V5
- Page 1 EN71 level, we cannot accept responsibility for your safety whilst erecting or using this product. For assistance please contact customer care on: 01636 821215 Refer to the instructions pages for your speci c product code Mercia Garden Products Limited, Sutton On Trent, Newark, Nottinghamshire, NG23 6QN www.merciagardenproducts.co.uk...
- Page 2 Log Board - 120x19x3296mm QTY 19 LB19-A-3296 Log Board - 120x19x1123mm QTY 24 LB19-B-1123 Before assembly please make sure you have a suitable base ready to erect your Closure Trim - 16x28x2400mm (approx length) QTY 14 building S1628-2400 Roof Purlin - 90x40x3000mm QTY 3 F4090-3000 MADE IN GREAT BRITAIN Bearer - 44x44x3011mm QTY 10...
- Page 3 Pre-assembly Felt *Please note: Each board interlocks at either end in a staggered pattern. Before securing ensure that the boards are tted properly in their respective Log Board - 110x19x2996mm QTY 1 tongues and grooves. LB19RG110-A-2996 Roof Spacers QTY 5 PI-07-0208 (20x100x2mm) Nail Bag 30mm Screw x102...
- Page 4 Step 2 Step 1 IMPORTANT: Pre-drill before xing screws. IMPORTANT: Pre-drill before xing screws. Parts Needed - No. 4 QTY 2 Parts Needed - No. 13 QTY 10 No. 5 QTY 2 No. 14 QTY 2 No’s. 4 No’s. 13 & &...
- Page 5 Step 3 Step 5 Parts Needed - No. 5 QTY 12 Parts Needed - No. 5 QTY 6 No. 6 QTY 6 No. 7 QTY 13 No. 7 QTY 6 No. 8 QTY 7 No. 9 QTY 6 No. 9 QTY 7 No.
- Page 6 Step 7 Step 9 Parts Needed - No. 9 QTY 1 No. 24 QTY 1 No. 20 QTY 1 s No. 1 No. 21 QTY 1 Pre-Assembly No’s. 9 & 20 *Ensure the boards are level with each end. No’s. 24 & 21 *Please note: This image is for illustrative purposes and may *Ensure that the boards are...
- Page 7 Step 11 IMPORTANT: Pre-drill before xing screws. Parts needed - No. 12 QTY 3 Step 12 Parts needed - No. 18 QTY 56 s No. Front roof boards No. 18 Front view ensure to pre-drill to avoid the boards No. 24 splitting *Please note: The gable shown is for illustrative purposes and may differ...
- Page 8 Step 13 Parts Needed - No. 16 QTY 2 Step 14 Parts Needed - No. 17 QTY 29 No. 17 No. 16 internally *Please Note: This image is for illustrative purposes and may differ from your choice in product. Nevertheless the process of xing the eaves frames is the same.
- Page 9 Step 15 Step 17 Parts needed - No. 11 QTY 7 Roof Roof Parts needed - No. 22 No. 11 *Ensure there is approximately 50mm of overhanging felt each side. Internal Internal *Measure and cut the *Measure and cut the Closure Trim Closure Trim closure trims to...
- Page 10 IMPORTANT: Pre-drill before xing screws. Step 18 Step 19 Parts Needed - No. 15 QTY 4 Parts needed - No. 19 QTY 8 No. 15 No. 19 internally *Ensure the angled cuts meet at the top of the apex. 12x40mm Screws 40mm Pre drill screw...
Need help?
Do you have a question about the 0619LOG003-V5 and is the answer not in the manual?
Questions and answers