Table of Contents
Advertisement
3.11.6.2 To change the PIN code
1.
Select
Security > Change PIN code in the app.
2.
Enter the PIN code.
3.
Enter the new PIN code.
4.
Enter the new PIN code to confirm.
5.
Make a note of the new PIN code in Memo. Refer
Introduction on page 3 .
to
3.11.6.3 Theft protection
Theft protection menu it is possible to set the
In the
alarm duration and also what events should trigger the
alarm. The factory setting is to require PIN code and the
alarm duration is 1 min.
Time lock
The time lock can be set between 1 to 100 days. The
factory setting is 30 days. When the selected number of
days has gone by, the product continues to operate as
usual. To enter new settings the PIN code must be
entered.
Require PIN code
This function means that the product cannot be operated
or controlled after the STOP button has been pushed
without first entering the correct PIN code. If the
incorrect PIN code is entered 5 times, the product is
locked for a time. The lock is extended for each new
incorrect try.
Alarm duration
There is a possibility to set how long the alarm signal
should last. A setting between 1 and 10 minutes is
possible.
STOP button pressed
"STOP button pressed" is enabled, the
If the alarm
alarm goes off if someone presses the STOP button and
the PIN code is not entered within 30 seconds.
Carried away
Carried away is enabled, the product senses
If the alarm
unexpected motions, and the alarm goes off.
To set the Theft protection
Settings > Security > Theft protection in the
1.
Select
app.
2.
Select the on/off button to enable or disable the
Time lock, Require PIN code, STOP button
pressed and Carried away .
3.
Move the horizontal bar to select the duration of
the alarm.
3.11.6.4 GeoFence
GeoFence is a GPS-based theft protection that makes a
virtual fence for the product. If the product is more than
a set distance away from the center position the product
will be deactivated and an alarm will start. The PIN code
is needed to deactivate the alarm and to start the
product again.
1457 - 005 - 16.10.2020
To set the center position and radius for the GeoFence
function
Settings > Security > GeoFence in the app.
1.
Select
2.
Put the product in a central position of the work
area.
3.
Select the
on/off button to enable or disable the
GeoFence function. The center position will be set
to the current position of the product.
4.
Use the horizontal bar to set the radius.
®
3.11.7 Automower
Connect (Bluetooth
only)
®
Automower
Connect you can enable or disable the
In
®
Automower
Connect module. You can also see the
signal strength, connectivity status, initiate new pairing
or remove the product from the paired accounts.
3.11.8 Messages (Bluetooth
In this menu the previous fault and information
messages can be found. For some of the messages,
there are tips and advice to help to rectify the fault.
Note:
The
Messages menu is only available for
®
Bluetooth
short-range connectivity.
If the product is disrupted in any way, for example it is
trapped or the battery is low, a message is saved
relating to the disruption and the time it happened.
If the same message is repeated several times, this may
indicate that an adjustment to the installation or the
product is required. Refer to
Installation on page 14 .
3.11.9 Husqvarna Fleet Services
™
Husqvarna Fleet Services
is a cloud solution that gives
the commercial fleet manager an overview of all
products. It also gives the fleet manager the possibility
to control all products remotely. Husqvarna Fleet
™
Services
is included for Automower
more information about Husqvarna Fleet Services
refer to www.husqvarna.com.
3.11.9.1 To connect to the product with Husqvarna Fleet
™
Services
1.
Download the Husqvarna Fleet Services
®
Automower
Connect app to your mobile device.
2.
Create a Husqvarna Fleet Services
(www.husqvarna.com).
3.
Log on to the Husqvarna Fleet Services
4.
Set the Main switch on the product to position
®
®
only)
™
®
520H/550H. For
™
,
™
app and
™
account
™
app.
1 .
Installation - 29
Advertisement
Table of Contents
