Toro Greensmaster eTriFlex 3370 Operator's Manual page 24

Mowing Reel Speed Options (cont'd.)
6
7
8
9
Note:
The factory default setting is 2000 rpm
(increment number 9).
Adjusting the Backlap Reel Speed
Navigate to the B
ACKLAP
speed while performing a backlap operation.
Refer to the following table for the reel speed options
and their corresponding increment numbers:
Backlap Reel Speed Options
Increment Number
1
2
3
4
5
6
7
8
9
Note:
The factory default setting is 200 rpm
(increment number 1).
Adjusting the Clip-Control Feature
Understanding the Radius-Dependent-Speed
(RDS) System
To achieve a consistent, high quality-of-cut and a
uniform after cut appearance, the machine is equipped
with the patent-pending Radius Dependent Speed™
(RDS) system. The RDS system is a clip-control
and independent wheel-speed feature that varies the
speeds of each reel motor and each traction motor to
maintain a constant clip and reduce turf scrubbing in
turns while cutting.
When the machine is turning while cutting (e.g., during
the clean-up pass), the reel on the inside of the turn
will rotate at a slower rpm than the reel on the outside
of the turn. The center reel splits the difference of the
inside and outside reel speeds so that all three cutting
units have the same clip. The sharper the turn, the
1550
1700
1850
2000
RPM option to adjust the reel
Reel Speed (RPM)
200
240
280
320
360
400
440
480
520
greater the difference in reel speeds. Additionally, if
the machine speed changes while you are cutting,
the RDS system adjusts the reel speed to maintain a
constant clip. This feature reduces turf thinning on
the inside reel (in comparison to other riding greens
mowers), which can reduce triplex ring.
The RDS system also adjusts each wheel-motor
speed during a turn, similar to the reel-motor speeds
changing in a turn. The inside wheel motor will turn
at a slower rpm than the outside wheel motor. This
minimizes wheel scrubbing in the turn and can reduce
triplex ring.
Setting the Clip-Control Feature
Navigate to the C
LIP
system feature.
•
Clip control set to ON: The machine uses your
settings from the H
C options and the left and right wheel speeds
OUNT
to determine the speed of each reel.
•
Clip control set to O
setting from the R
rotate at a constant rate.
Note:
The factory default setting is ON.
Adjusting the Height of Cut (HOC)
Navigate to the H
EIGHT OF
the height of cut. The clip control feature must be
set to O to use this feature; refer to
N
Clip-Control Feature (page
Note:
The factory default setting is 3.2 mm (0.125
inch).
Adjusting the Number of
Cutting-Unit Blades
Navigate to the B
LADE
number of cutting-unit blades. Determine the number
of blades in your equipped cutting units, and select
the appropriate value (5, 8, 11, or 14).
Note:
The factory default setting is 11.
Adjusting the Maximum Mowing
Speed
Navigate to the M
AX
maximum mowing speed. You can adjust the speed
from 4.8 km/h (3.0 mph) to 8.0 km/h (5.0 mph) in
increments of 0.3 km/h (0.2 mph).
Note:
The factory default setting is 6.1 km/h (3.8
mph).
24
C option to set the RDS
ONTROL
C (HOC) and B
EIGHT OF UT
: The machine uses your
FF
S option. The reels
EEL PEED
C (HOC) option to adjust
UT
Setting the
24).
C option to adjust the
OUNT
M option to adjust the
OW
LADE