Checking The Machine After Starting The Engine; Shutting Off The Engine; Checking The Safety-Interlock System - Toro Greensmaster TriFlex 3400 Operator's Manual

4. Insert the key into the switch and rotate it to the
O position. Hold it in the O
N
glow-plug-indicator light goes off (approximately
6 seconds).
5. Turn the ignition key to the S
Important:
To prevent overheating of the
starter motor, do not engage the starter
longer than 10 seconds. After 10 seconds of
continuous cranking, wait 60 seconds before
engaging the starter motor again.
6. Release the key when the engine starts and
allow it to move to the O
7. Allow the engine to warm up for a few minutes
before operating.
Important:
When starting the engine for the
first time or after an overhaul of the engine,
operate the machine in forward and reverse
for 1 to 2 minutes. Turn the steering wheel
to the left and right to check the steering
response. Then shut the engine off and wait
for all moving parts to stop; refer to
Off the Engine (page
leaks, loose parts and any other noticeable
malfunctions.
Checking the Machine after
Starting the Engine
1. Move the throttle lever to the F
2. Move the raise/lower mow control lever forward
momentarily.
The cutting units should lower and all the reels
should rotate.
Note:
The function lever should be in the
middle (mow) position for the reels run when
lowering the cutting units
3. Move the raise/lower mow control lever
rearward.
The cutting reels should stop rotating and the
cutting units should raise to the full transport
position.
4. Engage the brake to keep the machine from
moving, and operate the traction pedal through
the forward and reverse positions.
5. Continue the above procedure for 1 or 2
minutes. Move the functional-control lever to the
N position, engage the parking brake,
EUTRAL
and shut off the engine.
6. Check for fluid leaks and tighten the hydraulic
fittings if any leaks are found.
Note:
When the machine is new and the
bearings and reels are tight, it is necessary
position until the
N
position.
TART
position.
N
Shutting
24). Check for oil
position.
AST
to use the F
AST
check. A fast throttle setting may not be required
after the break-in period.
Note:
If fluid leaks continue to appear, contact
your authorized Toro distributor for assistance
and, if necessary, replacement parts.
Important:
A trace of fluid on the motor or
wheel seals is normal. Seals require a small
amount of lubrication to perform properly.

Shutting Off the Engine

1. Move the throttle lever to the S
back the raise/lower mow control, and move the
functional-control lever to the N
2. Rotate the ignition key to the O
shut off the engine. Remove the key from the
switch to prevent accidental starting.
3. Close the fuel-shutoff valve before storing the
machine.
Checking the
Safety-Interlock System
Service Interval: Before each use or daily
CAUTION
If the safety interlock switches are
disconnected or damaged the machine could
operate unexpectedly, causing personal
injury.
• Do not tamper with the interlock switches.
• Check the operation of the interlock
switches daily and replace any damaged
switches before operating the machine.
The purpose of the safety-interlock system is to
prevent operation of the machine where there is
possible injury to you or damage to the machine.
The safety-interlock system prevents the engine from
starting unless:
•
The traction pedal is in the N
•
The functional-control lever is in the N
position.
The safety-interlock system prevents the machine
from moving unless:
•
The parking brake is disengaged.
•
You are seated in the operator's seat.
•
The functional-control lever is in the M
or the T
RANSPORT
24
throttle-lever position for this
position, pull
LOW
EUTRAL
position to
FF
position.
EUTRAL
EUTRAL
OW
position.
position.
position