Related Manuals for BayWa novotegra closed II
Summary of Contents for BayWa novotegra closed II
- Page 1 Mounting instructions novotegra for flat roof closed II / east-west II Subjects excepted. Illustrations are exemplary and may vary from the original. V3.3 - April 2020/ASc, Copyright BayWa r.e. Solar Energy Systems GmbH...
-
Page 2: Table Of Contents
5.2 Module installation, load redistribution and ballast ........... 9 5.3 Mounting variations ..................11 6 Warranty / product liability (exclusion) ............16 Subjects excepted. Illustrations are exemplary and may vary from the original. V3.3 - April 2020/ASc, Copyright BayWa r.e. Solar Energy Systems GmbH... -
Page 3: Notes
After receipt the goods must be inspected for completeness using the accompanying delivery note. BayWa r.e. Solar Energy Systems GmbH does not accept the costs, nor can we guarantee subsequent express deliveries if missing material is only noticed during mounting. - Page 4 (project data recording). Deviations from the planning on site may lead to different results. Subjects excepted. Illustrations are exemplary and may vary from the original. V3.3 - April 2020/ASc, Copyright BayWa r.e. Solar Energy Systems GmbH...
-
Page 5: Maintenance Of The Mounting System
The maintenance work must be carried out by a specialist company with proven experience in electrical systems and work on mounting systems. Subjects excepted. Illustrations are exemplary and may vary from the original. V3.3 - April 2020/ASc, Copyright BayWa r.e. Solar Energy Systems GmbH... -
Page 6: Novotegra For Facade
(e.g. suitable stones), based on the results of the wind tunnel tests for the system. The required ballast is determined by BayWa r.e. Solar Energy Systems GmbH based on the project data provided by the installation company. The ballast applies to the planned system; on-site deviations from planning may lead to different results. -
Page 7: System Components, Tools And Equipment
* The components vary depending on the requirements of the roof, the structural analysis and the choice of components and may deviate from the images above. Subjects excepted. Illustrations are exemplary and may vary from the original. V3.3 - April 2020/ASc, Copyright BayWa r.e. Solar Energy Systems GmbH... -
Page 8: Mounting System Components - Mounting Versions
PE pad 140 x 390 x 20 mm Material: PE foam ** Required components for ballast distribution at system edge, depending on substructure construction. Subjects excepted. Illustrations are exemplary and may vary from the original. V3.3 - April 2020/ASc, Copyright BayWa r.e. Solar Energy Systems GmbH... -
Page 9: Mounting System Components - Optional
*** Optionally available installation system components, e.g. for improving the aesthetics of the system, cable management or grounding of the installation system. Subjects excepted. Illustrations are exemplary and may vary from the original. V3.3 - April 2020/ASc, Copyright BayWa r.e. Solar Energy Systems GmbH... -
Page 10: Installing The Mounting System
The distance between the base troughs in the joint may not exceed 100 mm. Subjects excepted. Illustrations are exemplary and may vary from the original. V3.3 - April 2020/ASc, Copyright BayWa r.e. Solar Energy Systems GmbH... -
Page 11: Module Installation, Load Redistribution And Ballast
II. Connect the cables of adjacent modules while installing them. Place the string cables first. Subjects excepted. Illustrations are exemplary and may vary from the original. V3.3 - April 2020/ASc, Copyright BayWa r.e. Solar Energy Systems GmbH... - Page 12 / put on the required ballast. Further rails can be used to redistribute load: C-rail 47, 71 and 95, support brace Subjects excepted. Illustrations are exemplary and may vary from the original. V3.3 - April 2020/ASc, Copyright BayWa r.e. Solar Energy Systems GmbH...
-
Page 13: Mounting Variations
System edge / expansion joint: = module length – 69 mm Module joint: = module length + 12 mm Subjects excepted. Illustrations are exemplary and may vary from the original. V3.3 - April 2020/ASc, Copyright BayWa r.e. Solar Energy Systems GmbH... - Page 14 17 m, with the base trough expansion joint approx. 34 m, plan for proper expansion joints after this. Subjects excepted. Illustrations are exemplary and may vary from the original. V3.3 - April 2020/ASc, Copyright BayWa r.e. Solar Energy Systems GmbH...
- Page 15 Wire adjacent modules when installing them. Install the string cable first. Subjects excepted. Illustrations are exemplary and may vary from the original. V3.3 - April 2020/ASc, Copyright BayWa r.e. Solar Energy Systems GmbH...
- Page 16 (3). The coupling profile is only firmly secured to one base trough. Distance between base troughs 50 mm. Subjects excepted. Illustrations are exemplary and may vary from the original. V3.3 - April 2020/ASc, Copyright BayWa r.e. Solar Energy Systems GmbH...
- Page 17 Tightening torque as described above. The contact plate is used for equipotential bonding and lightning current carrying capacity of the system. Subjects excepted. Illustrations are exemplary and may vary from the original. V3.3 - April 2020/ASc, Copyright BayWa r.e. Solar Energy Systems GmbH...
-
Page 18: Warranty / Product Liability (Exclusion)
BayWa r.e. Solar Energy Systems GmbH sales team before mounting the novotegra mounting system or – in the case of components not supplied by BayWa r.e. Solar Energy Systems GmbH – the manufacturer concerned. - Page 19 BayWa r.e. Solar Energy Systems GmbH Eisenbahnstraße 150 D-72072 Tübingen Tel. +49 7071 98987-0 Fax +49 7071 98987-10 solarenergysystems@baywa-re.com www.baywa-re.com solar-distribution.baywa-re.de novotegra.de Subjects excepted. Illustrations are exemplary and may vary from the original. V3.3 - April 2020/ASc, Copyright BayWa r.e. Solar Energy Systems GmbH...