Download Print this page
Montigo PL Series Installing
Montigo PL Series Installing

Montigo PL Series Installing

Porcelain panel kit

Advertisement

Quick Links

Installing the PL Series Porcelain Panel Kit
This kit may be used on the following models:
• PL38DF
• PL42DF
• PL52DF
CAUTION
Ensure that all power to the appliance is off at the electrical breaker or fuse
before beginning installation. Ensure gas is turned off at the shutoff valve before
beginning installation.
WARNING
Some materials used in the manufacturing process of this product can
expose you to Benzene which is known in the State of California to
cause cancer and birth defects or other reproductive harm. For more
information go to www.P65warnings.ca.gov
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
Page 1
®
C
US
Warning: If the information in these instructions is not followed exactly, a fire or
explosion may result causing property damage, personal injury or loss of life.
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or
any other appliance.
What To Do If You Smell Gas:
instructions.
If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified installer, service agency or the gas supplier.
The installation of this kit must be done by a qualified
and certified gas appliance installer.
Check local codes and read all instructions prior to
installation.
When installing the replace - gas lines, ttings, accesso-
ries or any other objects cannot impede the proper
movement of the door buckles.
WARNING
XT0048 - 160426
Upgrade Kit

Advertisement

loading
Need help?

Need help?

Do you have a question about the PL Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Montigo PL Series

  • Page 1 Upgrade Kit Installing the PL Series Porcelain Panel Kit This kit may be used on the following models: • PL38DF • PL42DF • PL52DF The installation of this kit must be done by a qualified  and certified gas appliance installer.
  • Page 2 Left Panel Tools Required: Drill / Driver • Figure 1: PL Series Porcelain Panel Kit Contents Before you begin: Installation: Always ensure the kit part number is correct for the Step 1: Remove the fireplace screen barrier by grasping fireplace model and all kit contents are included. The the top flange at both sides and pulling outward.
  • Page 3 Installation Step 2: Remove the horizontal access panel. Step 4: Release the door buckles using the door buckle tool. Hand-hold Door Latch Slot Door Latch Hook Figure 5: Door buckle tool Figure 6: Grasp hand-hold end of Door buckle tool and place the machined end in the slot under door frame Figure 3 Figure 7: Ensure the tool is firmly in the lower end of the slot as...
  • Page 4 Installation Step 4: Remove the burner media. Take care to avoid scratching the paint on the burner or burner tray. Figure 9: Remove the tool from the latch slot. Ensure the latches are hanging freely, the hook end is released from the bottom of the door.
  • Page 5 Installation Step 6: Remove pilot cover. Step 8: Remove tek screws securing the rear air deflector. Figure 16 Figure 14 Step 7: Remove burner tray. Step 9: Remove the rear air deflector. Figure 15 Figure 17 Page 5 XT0048 - 160426...
  • Page 6 Installation Step 13: Secure the top and bottom clips using tek Step 10: Align the rear porcelain panel with the back side screws. of the fireplace. The flat edge of the panel aligns with the top of the fireplace. Top Clips Note: handle porcelain panels with care to avoid damage to the panel or burner.
  • Page 7 Installation Step 17: Reinstall the pilot cover. Step 15: Reinstall the rear air deflector. Figure 25 Step 18: Reinstall the front air deflector. Figure 23 Step 16: Reinstall the burner media tray and secure Figure 26 using screws. Figure 24 Page 7 XT0048 - 160426...
  • Page 8 Installation Step 19: Reinstall the burner media. Step 21: Reinstall the horizontal access panel. Figure 29 Figure 27 Step 22: Reinstall the screen barrier by inserting the Step 20: Reinstall the door. Installation is the reverse of posts on the bottom of the screen and pressing the removal.
  • Page 9 Notes Page 9 XT0048 - 160426...
  • Page 10 PL Series Porcelain Panel Installation XT0048 - 160426...