Santec AVA General Installation Instructions

INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
DESCRIPTION
TRIM INSTALLATION
MECH ANICA L STOP
PLEASE READ THE INSTRUCTIONS COMPLETELY
This product is precision engineered to provide satisfactory performance provided it is installed and operated in
- Place the shower plate on the all thread
BEFORE BEGINNING THE INSTALLATION.
LIMIT STOP
accordance with our recommendations contained in this manual. In order to fully enjoy the comfort, safety and the
- Secure the plate by inserting plastic washer and lock nut onto
reliability of your pressure balancing valve, be certain to familiarize yourself with the contents of this manual.
all thread and make sure that the plate is secured..
- Thread the handle set with the washer and adapter onto all thread
STOP POST
WALL LINE
with the stem and mark the position.
- Take off the handle assembly and cut off the excess thread and stem.
Illustration D1
- Keeping the handle set at 6 o'clock position, thread handle assembly
onto all thread by using escutcheon being caution not to over tighten.
MECH ANICA L STOP
- Tightening the set screw using the allen key and insert the o-ring
and vent plug to cover the hole.
LIMIT STOP
STOP POST
46"
Illustration D2
TROUBLE SHOOTING
FLOOR
LINE
MALFUNCTION
Shower control opening through hot.
INSTALLATION
H
Tub filler or Shower head drips after
shutting off the valve.
NOTE: Failure to follow these instructions may cause damage or improper operations and nullify the warranty.
ROUGH IN
Shower insufficiently hot.
- Make sure the water supplies are off.
No flow of hot or cold water.
- Remove all the trim items (plate, handle and flange) before installation.
- Secure the valve firmly against the stud. Make sure the ½" shower outlet is in the up position.
- Make sure to flush or raise grouting on the tiled wall surface.
- Adjust the All Thread depth against the Teflon Washer and Limit Stop.
Valve body too deep into
the wall. Screw the All Thread against the Teflon washer until it is pressured gently against each other.
- Tighten firmly the Lock Nut against the Lock Plate.
- Position the valve using the dimension shown in the illustration B.
NOTE: AT NO TIME TRY TO STOP DRIPPING BY APPLYING EXTREME FORCE WHEN CLOSING THE VALVE.
3. 25 "
O-RIN G
FILT ER
INLET
FILT ER INSERT
VALVE
center of inlet
ILLUSTRATION C
KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE
TEMPERATURE LIMIT STOP SET UP
-Santec Pressure Balanced Valve has a temperature limit stop ( please see Illustration C)
which once set properly can provide a safe and comfortable hot water.
Below is the limit stop installation procedure:
- Remove all Handle trim parts, including the trim plate.
- remove all internal parts up to the Limit Stop, do not remove the Mechanical Stop.
After Mechanical Stop is removed please follow the instruction bellow
- Turn the cartridge clockwise until it is stopped. Do not force to avoid damaging the cartridge.
78"
(1981 mm)
- Insert the Mechanical Stop onto the cartridge
- Turn the cartridge counterclockwise to open the water line. Turn until it reaches the maximum
hot water desired by the user.
- Place Limit Stop as shown in the Illustration D2.
- Reinstall all the parts accordingly to the Illustration C.
HOT
CAUSE
- Hot and cold water supplies have been connected
WARMER
in reverse
- Water remains in the piping column to the shower
WARM
head (this is normal).
- Incorrect setting of the mechanical stop against the
stop post causing a partially opened cartridge. C OLD
- O-ring seal on the inlet of the cartridge is faulty.
- Adjustable handle position stop incorrectly set.
- Either the hot or cold side is not fully pressurized.
- Debris caught inside the inlet of the cartridge.
.
- The measured rough in or finished wall surface is
PM-280 - SERVICE VALVE (OPTIONAL)
incorrect.
FILTER SCREEN - Te012
VALVE CARTRIDGE - TE010
FILTER SCREEN REMOVAL AND CLEANING
Trim Plate
The valve has filter screens that prevent debris from obstructing the pressure balancing cartridge.
If excessive in-line debris accumulates in the filter screen you will notice a decrease in flow from the valve.
PLEASE NOTE - SHUT OFF BOTH HOT AND COLD WATER SUPPLIES BEFORE SERVICING VALVE.
All Thread - The filter screen are attached to an insert that is fitted into the valve body inlets.
With the cartridge removed the 2 inserts and filter screens can be easily removed from the valve body.
Stem
- Remove the insert by pressing the top corner. This will rotate the insert allowing easy removal.
- There is a place on either side of the filter insert where you can get your finger nail underneath the filter screen.
By pulling the filter screen away from the insert it will "pop out".
- All debris can be now be easily removed from the filter screen.
Lock Nut
Replace the filter screen into the insert and push together gently until it clicks into place.
- Place the insert back into the valve body, making sure the angled edge of the insert faces out.
Lock Plate
The insert should sit flush against the wall of the valve body when properly installed.
nished wall
PLASTIC WASHER
SPECIFICATIONS AND DIMENSIONS
Minimum oper
Maximum operating pressure 145 psi
Maximum test pressure
Hot and cold water inlets
Shower outlet
Flow capacity 5 USGPM @ 50 psi
Finished wall adjustment : see Illustration B
Rotate cartridge
C
- Allow approximately 3-5 minutes to drain column.
- Reset the mechanical stop as described in this page
- Check O-ring for cut or damage and replace if necessary.
- Check hot water source temperature setting.
- Be sure service stops (when applicable) are both wide open
- Remove cartridge and flush out or remove any debris lodged
install the extension kit.
PM460X(long sleeve).
PM461X (long plastic upper link)
LEVER PLUG O-RING
MECHANICAL STOP- TE013
PLASTIC WASHER LOCK NUT
LIMIT STOP- TE014
PM-007-1 - STEM
TEFLON WASHER
Santec Inc.
3501 Challenger Street, Torrance, CA 90503
Tel: (310) 542-0063 Fax (310) 542-5681
www.santecfaucet.com
Pressure Balanced Shower
Pressure Balanced Shower
Pressure Balanced Shower
Pressure Balanced Shower
HANDLE ASSEMBLY
LOCK NUT
This is a general installation instruction
for the following collections:
* AVA
* AVA CRYSTAL
Trim Plate
All Thread
500 psi
Lock Nut
Lock Plate
½" IPS
½" IPS
REMEDY
and system is fully pressurized.
inside the hot or cold inlet.
VENT PLUG
SET SCREW
PM-009 - LOCK PLATE
HANDLE ASSEMBLY
PM-012 - LOCK NUT
PM-011 - ALL THREAD
ILLUSTRATION B
10/07
Stem
PAGE 02
PAGE 03
PAGE 01
PAGE 04