Advertisement
ENGLISH
Introduction
Congratulations on your purchase and welcome to Philips! To fully benefit
from the support that Philips offers, register your product at www.philips.com/
welcome.
Important
Read this user manual carefully before you use the appliance and save it for
future reference.
Danger
-
Keep the charger away from water. Do not place or store it over or near
water contained in a bathtub, washbasin, sink etc. Do not immerse
the charger in water or any other liquid. After cleaning, make sure the
charger is completely dry before you connect it to the mains.
Warning
-
The mains cord cannot be replaced. If the mains cord is damaged,
discard the charger.
-
Always have the charger replaced with one of the original type in order
to avoid a hazard.
-
Do not use the charger outdoors or near heated surfaces.
-
If the appliance is damaged in any way (brush head, toothbrush handle
or charger), stop using it. This appliance contains no serviceable parts.
If the appliance is damaged, contact the Consumer Care Centre in your
country (see chapter 'Guarantee and support').
-
This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
-
Children should be supervised to ensure that they do not play with
the appliance.
Caution
-
Do not clean the brush head, the handle or the charger in the dishwasher.
-
If you have had oral or gum surgery in the previous 2 months, consult
your dentist before you use the toothbrush.
-
Consult your dentist if excessive bleeding occurs after using this
toothbrush or if bleeding continues to occur after 1 week of use. Also
consult your dentist if you experience discomfort or pain when you use
the Philips Sonicare.
-
The Philips Sonicare toothbrush complies with the safety standards for
electromagnetic devices. If you have a pacemaker or other implanted
device, contact your physician or the device manufacturer of the
implanted device prior to use.
-
If you have medical concerns, consult your doctor before you use the
Philips Sonicare.
-
This appliance has only been designed for cleaning teeth, gums and
tongue. Do not use it for any other purpose. Stop using the appliance
and contact your doctor if you experience any discomfort or pain.
-
The Philips Sonicare toothbrush is a personal care device and is not
intended for use on multiple patients in a dental practice or institution.
-
Stop using a brush head with crushed or bent bristles. Replace the brush
head every 3 months or sooner if signs of wear appear. Do not use other
brush heads than the ones recommended by the manufacturer.
-
If your toothpaste contains peroxide, baking soda or bicarbonate (common in
whitening toothpastes), thoroughly clean the brush head with soap and water
after each use. This prevents possible cracking of the plastic.
Electromagnetic fields (EMF)
This Philips appliance complies with all applicable standards and
regulations regarding exposure to electromagnetic fields.
Your Philips Sonicare (Fig. 1)
1
Replaceable Philips Sonicare brush head
2 Battery charge indicator (specific types only)
3 Power on/off button
4 Handle
5 Charger
Preparing for use
Attaching the brush head
1
Align the brush head so the bristles point in the same direction as the
front of the handle.
2 Firmly press the brush head down onto the metal shaft until it stops.
Note: There is a small gap between the brush head and the handle.
Charging the appliance
1
Put the plug in the wall socket.
2 Place the handle on the charger.
3 The battery charge indicator shows the approximate remaining battery charge.
-
Solid green light: 50-100%
-
Flashing green light: 5-49%
-
Flashing green light and 3 beeps after the brushing cycle: less than
5% and toothbrush has to be recharged.
Note: To keep the battery fully charged at all times, you may keep your
Philips Sonicare on the charger when not in use. It takes at least 24 hours to
fully charge the battery.
Using your Philips Sonicare
Brushing instructions
1
Wet the bristles and apply a small amount of toothpaste.
2 Place the toothbrush bristles against the teeth at a slight angle (45 degrees),
pressing firmly to make the bristles reach the gumline or slightly beneath the
gumline. (Fig. 3)
Note: Keep the center of the brush in contact with the teeth at all times.
3 Press the power on/off and mode button to turn on the Philips Sonicare.
4 Apply light pressure to maximize Philips Sonicare's effectiveness and let
the Philips Sonicare toothbrush do the brushing for you. Do not scrub.
5 Gently move the brush head slowly across the teeth in a small back and
forth motion so the longer bristles reach between your teeth. Continue
this motion throughout the brushing cycle.
6 To clean the inside surfaces of the front teeth, tilt the brush handle semi-
upright and make several vertical overlapping brushing strokes on each tooth.
Note: To make sure you brush evenly throughout the mouth, divide your
mouth into 4 sections using the Quadpacer feature (see chapter 'Features').
7 Begin brushing in section 1 (outside upper teeth) and brush for
30 seconds before you move to section 2 (inside upper teeth). Continue
brushing in section 3 (outside lower teeth) and brush for 30 seconds
before you move to section 4 (inside lower teeth).
8 After you have completed the brushing cycle, you can spend additional
time brushing the chewing surfaces of your teeth and areas where
staining occurs. You can also brush your tongue, with the toothbrush
turned on or off, as you prefer. (Fig. 5)
Your Philips Sonicare is safe to use on:
-
Braces (brush heads wear out sooner when used on braces).
-
Dental restorations (fillings, crowns, veneers).
Note: When the Sonicare is used in clinical studies, the handle should
be fully charged. Deactivate the Easy-start feature and for areas where
excess staining occurs, an additional 30 seconds of brushing time can be
spent to assist with stain removal.
Features
Easy-start
This Philips Sonicare comes with the Easy-start feature activated.
The Easy-start feature gently increases the power over the first 14 brushings
to help you get used to the brushing with the Philips Sonicare.
Note: Each of the first 14 brushings must be at least 1 minute in length to
properly advance through the Easy-start ramp-up cycle.
Activating or deactivating the Easy-start feature
1
Attach the brush head to the handle.
2 Place the handle in the plugged-in charger.
To activate Easy-start:
Press and hold the power on/off and mode button for 2 seconds. You hear
2 beeps and the battery level indicator lights up green to indicate that the
Easy-start feature has been activated.
To deactivate Easy-start:
Press and hold the power on/off and mode button for 2 seconds. You hear
1 beep and the battery level indicator lights up yellow to indicate that the
Easy-start feature has been deactivated.
Note: Using the Easy-start feature beyond the initial ramp-up period is not
recommended and reduces Philips Sonicare effectiveness in removing plaque.
Smartimer
The Smartimer indicates that your brushing cycle is complete by
automatically turning off the toothbrush at the end of the brushing cycle.
Dental professionals recommend brushing no less than 2 minutes twice a day.
If you want to pause or stop brushing during the 2-minute brushing cycle,
press and hold the on/off button for 2 seconds. Press the on/off button
again and the Smartimer picks up where you left off. The Smartimer
automatically resets to the beginning of a 2-minute cycle if:
-
you stop brushing for 30 seconds or longer.
-
you put the handle in the charger.
Quadpacer
The Quadpacer is an interval timer. At 30, 60 and 90 seconds, you hear a
short beep and pause in the brushing action. This is your signal to move to
the next section of your mouth.
Cleaning
Do not clean brush heads, the handle, the charger or the charger covers in
the dishwasher.
Toothbrush handle
1
Remove the brush head and rinse the metal shaft area with warm water.
Make sure you remove any residual toothpaste (Fig. 9).
Caution: Do not push on the rubber seal on the metal shaft with sharp
objects, as this may cause damage.
2 Wipe the entire surface of the handle with a damp cloth.
Brush head
1
Rinse the brush head and bristles after each use (Fig. 10).
2 Remove the brush head from the handle and rinse the brush head
connection with warm water at least once a week.
4235_020_4555_2_DFU-Lefalet_A6_v2.indd 2
Charger
1
Unplug the charger before you clean it.
2 Wipe the surface of the charger with a damp cloth. Make sure you
remove any toothpaste or other residue from the charger surfaces.
Replacement
Brush head
Replace Philips Sonicare brush heads every 3 months to achieve optimal
results. Use only Philips Sonicare replacement brush heads.
Recycling
-
Do not throw away the product with the normal household waste at the
end of its life, but hand it in at an official collection point for recycling. By
doing this, you help to preserve the environment.
Removing the rechargeable battery
Warning: PLEASE NOTE THAT THIS PROCESS IS NOT REVERSIBLE.
-
To remove the rechargeable battery, you need a flat-head (standard)
screwdriver. Observe basic safety precautions when you follow the
procedure outlined below. Be sure to protect your eyes, hands, fingers,
and the surface on which you work.
1
To deplete the rechargeable battery of any charge, remove the handle
from the charger, turn on the Philips Sonicare and let it run until it stops.
Repeat this step until you can no longer switch on the Philips Sonicare.
2 Insert a screwdriver into the slot located at the bottom of the handle and
turn counterclockwise to release the bottom cap (Fig. 13).
3 Hold the handle upside down and push down on the shaft to release the
internal components of the handle.
4 Insert the screwdriver under the circuit board, next to the battery
connections, and twist to break the connections. Remove the circuit
board and pry the battery from the plastic carrier (Fig. 14).
The rechargeable battery can now be recycled and the rest of the
product discarded appropriately.
Guarantee and support
If you need information or support, please visit www.philips.com/support
or read the separate worldwide guarantee leaflet.
Guarantee restrictions
The terms of the international guarantee do not cover the following:
-
Brush heads.
-
Damage caused by use of unauthorised replacement parts.
-
Damage caused by misuse, abuse, neglect, alterations or unauthorised
repair.
-
Normal wear and tear, including chips, scratches, abrasions,
discolouration or fading.
简体中文
简介
感谢您的惠顾，欢迎光临飞利浦！ 为了让您能充分享受飞利浦
提供的支持，请在 www.philips.com/welcome 上注册您的产品。
注意事项
使用本产品之前，请仔细阅读本使用说明书，
并妥善保管以备日后参考。
危险
- 使充电器远离水源。 切勿将它放置或存放在任何
有水的容器的上方或附近，如：浴盆、脸盆、
水池等。切勿将充电器浸入水或任何其他液体中。
清洁后，确保充电器完全干燥，再将其连接至电源。
警告
- 不得更换电源线。 如果电源线损坏，请丢弃充电器。
- 应始终使用原装型号的充电器进行更换，以免发
生危险。
- 切勿在户外或高温表面附近使用充电器。
- 如果本产品受到任何损坏（牙刷头、牙刷柄或充电
器），请勿再使用。 本产品不包含任何可维修零部
件。 如果本产品已损坏，请联系您所在国家/地区
的客户服务中心（请参阅"保修和支持"一章）。
- 产品不打算由有肢体、感官或精神能力缺陷或缺
少使用经验和知识的人（包括儿童）使用，除非
有负责他们安全的人对他们进行与产品使用有关
的监督或指导。
- 请照看好儿童，本产品不能用于玩耍。
- 必须安装需要固定的部件，以免它们掉入水中。
警告
- 请勿在洗碗机中清洗牙刷头、牙刷柄或充电器。
- 如果您在前 2 个月中曾做过口腔或牙龈手术，
请在使用本产品前先咨询您的牙医。
- 如果使用本产品后牙龈大量出血或在使用 1 周后
仍会出血，请咨询您的牙医。 如果使用飞利浦
Sonicare 时感觉不适或疼痛，也请咨询您的牙医。
- 飞利浦 Sonicare 牙刷符合电磁装置的安全标准。
有关任何涉及心脏起搏器或其他植入装置的问
题，请在使用之前咨询医生或相关植入装置的设
备制造商。
- 如果您有医学问题，请在使用飞利浦 Sonicare
前咨询医生。
- 本产品设计仅用于清洁牙齿、牙龈和舌头。 请勿
将其用作任何其它用途。 如果感觉任何不适或疼
痛，请停止使用本产品并与医生联系。
- 飞利浦 Sonicare 牙刷为私人用品，不可供牙医诊
所或机构对多位患者使用。
- 请停止使用变形或刷毛弯曲的牙刷头。 请每 3 个
月更换一次牙刷头，如果出现磨损迹象，应提前
更换。 切勿使用非制造商推荐的其他刷头。
- 如果您所用的牙膏中含有过氧化物、碳酸氢钠或
其它重碳酸盐（增白牙膏中的常见成份），则请
务必在每次使用后用肥皂和水彻底清洗刷头。
这可以预防可能出现的塑料破裂。
电磁场 (EMF)
本飞利浦产品符合所有有关暴露于电磁场的适用标
准和法规。
Philips Sonicare 声波震动牙刷（图 1）
1 可更换 Philips Sonicare 牙刷头
2 电池充电指示灯（仅限于特定型号）
3 开/关按钮
4 手柄
5 充电器
使用准备
安装牙刷头
1 对齐牙刷头，使刷毛方向与牙刷柄正面的方向一致。
2 用力将牙刷头向下按到金属轴上，直到按不动为止。
注意： 牙刷头与牙刷柄之间会有小的间隙。
为产品充电
1 将电源插头接入插座。
2 将牙刷柄放在充电器上。
3 电池充电指示灯可显示大约剩余的电量。
- 稳定绿灯： 50-100%
- 闪烁绿灯： 5-49%
- 刷牙周期后闪烁绿灯并发出 3 声哔声： 不足 5% 且牙刷必
须充电。
注意： 为确保电池始终电量充沛，您可在不使用时将飞利浦
Sonicare 声波震动牙刷置于充电器上。 电池至少需要 24 小
时才能充满电。
使用飞利浦 Sonicare 声波震动牙刷
刷牙说明
1 浸湿刷毛并挤上少量牙膏。
2 将 牙刷的刷毛以小角度（45 度）放在牙齿上，用力按下以
使刷毛接触牙龈或牙龈 (图 3)略下方。
注意： 始终将牙刷中间与牙齿接触。
3 按下电源开/关和模式按钮，打开飞利浦 Sonicare。
4 对 飞利浦 Sonicare 轻轻地施加一点压力以使其发挥最佳效
果，然后让飞利浦 Sonicare 为您刷牙。 请勿过度用力。
5 轻 柔地将牙刷头在牙齿间来回小幅度缓慢移动，以便长刷
毛能清洁牙缝。 在整个刷牙周期中连续这样移动即可。
6 要 清洁门牙内表面，请将刷柄呈半直立状倾斜，在每颗牙
齿上反复垂直震动。
注意： 为确保牙刷能均匀清洁整个口腔，可使用
Quadpacer 30 秒时段计时器功能将口腔分为 4 个区域
（参见"功能"一章）。
7 分 区为：上牙左侧，上牙右侧，下牙左侧，下牙右侧
8 在 完成刷牙周期之后，可以多花一些时间刷洗牙齿的咀嚼
面以及污垢容易出现的区域。 还可以使用该牙刷清洁舌
头，这时可以根据自己的喜好 (图 5)打开或关闭牙刷电源。
您的飞利浦 Sonicare 可安全用于：
- 牙齿矫正器（在牙齿矫正器上使用时，牙刷头磨损较快）。
- 修复牙体（补牙、齿冠、烤瓷牙）。
注意： 当 Sonicare 声波震动牙刷用于临床研究时，牙刷柄
应完全充电。 禁用 Easy-Start 刷牙动力增强装置。对于牙
垢过多的区域，可以多刷 30 秒来清除牙垢。
功能
Easy-start 刷牙动力增强功能
该飞利浦 Sonicare 声波震动牙刷出厂时已启用 Easy-start 刷
牙动力增强功能。
Easy-start 刷牙动力增强功能在最初 14 次刷牙时会缓慢增加
动力，以帮助您适应使用飞利浦 Sonicare 刷牙。
注意： 前 14 次刷牙每次时间至少为 1 分钟，以便正确度过
Easy-start 刷牙动力增强功能的循序渐进期。
启用或禁用 Easy-start 刷牙动力增强功能
1 将牙刷头安装到牙刷柄上。
2 将牙刷柄放到连接电源的充电座中。
要启用 Easy-start 刷牙动力增强功能：
按住电源开/关和模式按钮 2 秒钟。 您会听到 2 声蜂鸣音且电
池电量指示灯会呈绿色亮起，表示 Easy-start 刷牙动力增强
功能已启用。
要禁用 Easy-start刷牙动力增强功能：
按住电源开/关和模式按钮 2 秒钟。 您会听到 1 声蜂鸣音且电
池电量指示灯会呈黄色亮起，表示 Easy-start 刷牙动力增强
功能已禁用。
注意： 不建议在初始动力递增阶段后仍使用 Easy-start 刷牙动力
增强功能，这样做会降低飞利浦 Sonicare 去除牙菌斑的效果。
Smartimer 两分钟智能计时器
Smartimer 两分钟智能计时器在刷牙周期结束时会自动关闭牙
刷，指示您的设定刷牙周期已完成。
牙科专家建议每天刷牙两次，每次不少于 2 分钟。
在 2 分钟刷牙周期中，若要暂停或停止刷牙，请按开/关按钮
2 秒钟。 再次按下开/关按钮，Smartimer 两分钟智能计时器
将从断开的时间继续计时。 在以下情况下，Smartimer 两分
钟智能计时器将自动复位并从头计时 2 分钟：
- 刷牙暂停 30 秒以上。
- 将牙刷柄放回充电座。
Quadpacer 30 秒时段计时器
Quadpacer 30 秒时段计时器是一种间隔计时器。 在 30
秒、60 秒和 90 秒时，您将听到一声短促的哔声，并且刷牙
动作将会暂停。 这是您移到嘴巴下一个刷牙区域的信号。
清洁
切勿在洗碗机中清洗牙刷头、刷柄、充电器或充电器盖。
牙刷柄
1 卸 下牙刷头并用温水冲洗金属轴。 确保清除所有残留牙膏
(图 9)。
警告： 请勿使用尖锐物品按压金属轴上的橡胶密封圈，
否则可能造成损坏。
2 使用湿布擦拭牙刷柄的整个表面。
牙刷头
1 每次刷牙 (图 10)后冲洗牙刷头和刷毛。
2 从 牙刷柄上卸下牙刷头，每周至少用温水冲洗一次牙刷头
连接处。
充电器
1 清洁产品前，请先将充电器电源拔掉。
2 使 用湿布擦拭充电器的表面。 确保清除充电器表面的所有
牙膏或其他残留物。
更换
牙刷头
每 3 个月更换一次飞利浦 Sonicare 刷头，以获得效果。
仅使用飞利浦 Sonicare 替换刷头。
回收
- 弃置本产品时，请不要将其与一般生活垃圾放在一起，
应将其交给政府指定的回收中心。 这样做将有利于环保。
(Pb)
(Hg)
(Cd)
(Cr (VI) )
PCB's
X
O
O
O
SJ/T 11364
O
GB/T 26572
X
GB/T 26572
* 该 表格中所显示的"有害物质"在产品正常使用情况下不会
对人身和环境产生任何伤害。
* 该 表格中所显示的"有害物质"及其存在的部件向消费者和
回收处理从业者提供相关物质的存在信息， 有助于产品废弃
时的妥善处理。
拆下充电电池
警告： 注意此过程是不可逆的。
- 要取出充电电池，您需要一个平头（标准）螺丝刀。 按照
下面列出的步骤执行操作时，请遵循基本的安全措施。
务必保护好您的眼睛、手、手指以及工作台面。
1 要 耗尽充电电池的电量，可以从充电器上取下牙刷柄，
打开 Philips Sonicare 并让其运行直到停止。 重复这一步
骤，直到无法再启动 Philips Sonicare 声波震动牙刷。
2 将 螺丝刀插入牙刷柄底部的槽口，逆时针转动螺丝刀打开
底盖 (图 13)。
3 握 住牙刷柄，使牙刷柄顶部朝下并向下推动牙刷柄轴，
释放牙刷柄的内部元件。
4 将 螺丝刀插入电路板下面电池连接处的旁边，并拧动以断
开连接。 卸下电路板并从塑料电池槽 (图 14)中撬出电池。
充电电池即可回收，产品的其它部件也要适当地弃置。
保修和支持
如需信息或支持，请访问 www.philips.com/support 或阅读单
独的全球保修卡。
保修条款
国际保修条款中不包括以下各项：
- 牙刷头。
- 因使用未授权的备件而造成的损坏。
- 由于误用、滥用、疏忽、改装或擅自修理造成的损坏。
- 正常磨损和撕裂，包括裂口、擦痕、磨损、变色或褪色等。
(PBB)
(PBDE)
O
O
12/09/16 16:52
Advertisement
