Related Manuals for Alliance Laundry Systems AA3410
Summary of Contents for Alliance Laundry Systems AA3410
- Page 1 Automatic Washers Refer to Page 6 for Model Numbers WA194-PT-1 Part No. 33711R1 www.comlaundry.com September 2002...
-
Page 2: Table Of Contents
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... - Page 3 Timer No. 32228 Cycle Sequence (Five Cycle) ............93 Electronic Control Nos. 31305 or 33927P Cycle Sequence (Four Cycle) ........94 Electronic Control Nos. 31304P, 31307 or 33925P Cycle Sequence (Five Cycle).........95 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
-
Page 4: Section 1 - Safety Information
• Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure that the product is properly grounded and to reduce the risk of fire, electric shock, serious injury or death. W006R1 33711 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... -
Page 5: Locating An Authorized Servicer
Locating an Authorized Servicer Alliance Laundry Systems is not responsible for personal injury or property damage resulting from improper service. Review all service information before beginning repairs. Warranty service must be performed by an authorized technician, using authorized factory parts. If service is required after the warranty expires, Alliance Laundry Systems also recommends contacting an authorized technician and using authorized factory parts. -
Page 6: Section 2 - Introduction
Nameplate Location When calling or writing about your product, be sure to mention model and serial numbers. Model and serial Nameplate numbers are located on nameplate(s) as shown. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 7: Model Identification
AA3410 AA8431 AWE852 AWM332 AWM551 AA4410 AA9431 AWE931 AWM351 AWM631 AA4411 NA3812 AWE951 AWM352 AWM651 AA5420 NA4821 AWM230 AWM432 AA5421 NA6821 AWM250 AWM452 AA6421 NA8831 AWM331 AWM531 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 8: Section 3 - Troubleshooting
• Refer to appropriate wiring diagram. †Inoperative electronic control • Refer to Section 8 to check out the electronic control operation. * Mechanical Timer Models Only † Electronic Control Models only © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 9: No Cold Water
† Electronic Control Models only 3. NO WARM WATER POSSIBLE CAUSE TO CORRECT No hot water. • Refer to Paragraph 1. No cold water. • Refer to Paragraph 2. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 10: Water Fill Does Not Stop At Proper Level
Timer motor lead wire off timer terminal. • Refer to appropriate wiring diagram and reattach wire. Broken, loose or incorrect wiring. • Refer to appropriate wiring diagram. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 11: No Agitation
• Repair or replace transmission assembly. †Inoperative electronic control • Refer to Section 8 to check out the electronic control operation. * Mechanical Timer Models Only † Electronic Control Models only © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 12: Slow Spin Or No Spin
• Refer to appropriate wiring diagram. †Inoperative electronic control • Refer to Section 8 to check out the electronic control operation. * Mechanical Timer Models Only † Electronic Control Models only © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 13: Drive Motor Overload Protector Cycles Repeatedly
• Replace with correct screws or tighten. Base damaged (washer was dropped). • Replace base assembly. Balance ring not positioned properly on • Refer to Paragraph 46. transmission assembly. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 14: Water Leaking From Outer Tub
• Replace gasket. Obstruction in drain causing water to come over top • Remove obstruction. of outer drain tub cover. Tub-to-pump hose leaking at clamp. • Tighten clamp. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 15: Section 4 - Grounding
If a voltage reading is measured other than that 115 ± 12 illustrated, the qualified electrician should correct the problem. Round 115 ± 12 Grounding Prong Figure 1 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 16: Power Cord To Cabinet Top, Cabinet Top To Control Hood Mounting Bracket, Pressure Switch Mounting Bracket And Ground Tab On Graphic Panel
BRACKET, PRESSURE SWITCH MOUNTING BRACKET AND GROUND TAB ON GRAPHIC PANEL Power Cord Ground Wires Ground MECHANICAL TIMER MODELS Wires Power Cord Ground Wires Ground Wires ELECTRONIC CONTROL MODELS Figure 2 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 17: Main Wire Harness To Top Left Rear Corner Gusset Of Cabinet
W003 16. MAIN WIRE HARNESS TO TOP LEFT REAR CORNER GUSSET OF CABINET Ground Wires Figure 3 17. MOTOR TO MOUNTING BRACKET Ground Wire Figure 4 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 18: Section 5 - Service Procedures
Control Control Knob Assembly End Cap (Right) Graphic Clip Screw Panel GRAPHIC PANEL, CONTROL HOOD AND CONTROLS (MODELS AA9431, NA8831, NA8431, AWE951, AWE931 AND AWE852) Figure 5 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... - Page 19 Knob Skirt GRAPHIC PANEL, CONTROL HOOD AND CONTROLS (MODELS AA3410, AA4411, AA4410, AA5421, AA5420, NA3812, NA4821, AWM230, AWM250, AWM331, AWM332, AWM351, AWM352, AWM432, AWM452, AWM551 AND AWM531) Figure 6 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
-
Page 20: Timer
Refer to the control hood mounting bracket, and that the Figure 7. two screws are torqued down between 12 to18 inch pounds (14 to 21 cm-kg). © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 21: Temperature Switch
Remove six screws (3 on top and 3 at lower front) holding hood assembly to control hood Hinge Hinge rear panel and cabinet top. Attaching (Right) Screws Figure 9 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... - Page 22 Section 5 Service Procedures Door Front Procedure One Procedure Two Door Front Door Front Procedure Three Figure 10 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
-
Page 23: Agitator
If hooks are placed between the fin area, damage to agitator may occur. c. Using a rocking motion (back and forth) carefully lift agitator off drive bell. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... - Page 24 Refer to Figure 14. IMPORTANT: If large nut is turned clockwise when pulling drive bell, you will twist off the 1/4 inch bolt. Figure 14 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
-
Page 25: Front Panel
Use an adjustable wrench and turn large nut on tool CLOCKWISE to force drive bell down onto transmission shaft until bell bottoms out on shaft. d. Turn bolt out of transmission shaft and remove tool. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 26: Pump Belt
Remove belt from motor pulley and pull belt b. Pull bottom of panel away from washer until out through front of motor mount. hold-down clips (located on top flange of © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... - Page 27 Drive Pulley Wire harness must be installed ahead of spring. Drive Belt Motor Attaching Helper Screws Spring Idler Spring Figure 17 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
-
Page 28: Motor And Mounting Bracket
Helper Spring Positioning The round spring hook must be hooked in Motor Mounting rear hole for proper Bracket idler lever operation. Motor Attaching Screws Figure 18 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... - Page 29 (Clips to the motor Idler mounting bracket) Shaft Idler Ground Wire Pulley (Green) Felt Washers Belt Nylatron (Agitate and Spin) Washer Belt Retainer (Pump) Ring Figure 19 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
-
Page 30: Motor Drive Pulley Or Pump Pulley
NOTE: Refer to Wiring Schematics, Section 9, for rewiring internal switch wires. Pump Assembly Outer Tub to Pump Hose Drain Hose Pump Mounting Bracket Pump Attaching Hex Head Screws Screw Figure 20 Figure 21 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 31: Cabinet Top Assembly
Refer to Figure 23. IMPORTANT: Before lowering cabinet top into position, pivot outer tub forward far enough to prevent damaging (bending) the out-of-balance switch lever. Figure 23 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 32: Door Switch
IMPORTANT: When reinstalling cabinet top and before lowering top into position, pivot outer tub forward far enough to prevent damaging (bending) the out-of-balance switch lever. Figure 24 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 33: Out-Of-Balance Switch
NOTE: Make sure the switch is secure within the in the switch holder. Refer to Figure 29. holder by wiggling it back and forth. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... - Page 34 NOTE: Refer to wiring diagram located in hood area. m. Reinstall screws holding hood assembly to control hood rear panel and cabinet top. Switch Switch Holder Holder Slots Figure 29 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
-
Page 35: Mixing Valve Assembly
NOTE: Refer to appropriate wiring diagram when rewiring solenoids. d. Unhook the pressure hose from the retainer clips located on the left rear edge of the outer tub cover. Refer to Figure 32. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... - Page 36 Refer to Figure 33. the outer tub flange. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
- Page 37 Outer area and pull out and away from tub and at the same time lift up on tub cover to remove cover off tub flange. Figure 33 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
- Page 38 NOTE: When installing washtub, make sure lint filter is between underside of washtub and hub. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
-
Page 39: Hub And Seal Kit Assembly
Do this around the entire tub cover until the cover is free from Figure 35 the outer tub flange. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... - Page 40 Remove agitator drive bell. Refer to Paragraph j. Remove the seal head from the hub. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
- Page 41 Then place the hex nut on the with bronze portion of the seal. Refer to transmission tube (with the larger inside bevel Figure 37. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
- Page 42 Refer to Figure 33. d. Place the No. 294P4 Bell Tool over top of bell. Screw bolt into transmission shaft until it bottoms out. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
- Page 43 Figure 38 WARNING To reduce the risk of personal injury, be careful not to damage door switch and out- of-balance switch lever when reinstalling the cabinet top. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
-
Page 44: Outer Tub
Tabs taken not to twist or bunch the gasket in any one fingers area as this will cause a leak after assembly. Figure 40 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... - Page 45 A bent idler lever will h. Remove agitator drive bell. Refer to Paragraph cause misalignment of idler pulley with the drive belt, and a chipped idler pulley will damage belt. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
- Page 46 Remove hose clamp holding pressure hose to accumulator and grommet. pressure switch accumulator. Then remove pressure hose from retainer clips on outer tub cover. Refer to Figure 32. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
-
Page 47: Drive Pulley And Helix
IMPORTANT: When reinstalling belt, no drive belt Pivot entire pump assembly toward motor to adjustment is necessary. loosen belt tension. d. Run belt off motor pulley, then remove belt from pump assembly. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... - Page 48 Remove screw, washer and helix holding drive pulley to the input shaft of the transmission assembly. Refer to Figure 43. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
-
Page 49: Brake Assembly
NOTE: Refer to Figure 44 for assembly sequence. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 50: Lower Bearing Housing
Refer to Figure 33. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... - Page 51 Using No. 321P4 Spring Hook Tool, unhook Figure 44. five centering springs from lower edge of outer s. Lift brake assembly and pads off transmission tub. Refer to Figure 41. tube. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
-
Page 52: Transmission Assembly
Loosen hose clamp and disconnect filler hose of bearing opening. from backflow preventer. Refer to Figure 31. c. Clean any foreign material from outside diameter of new bearing. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... - Page 53 If the idler spring or helper spring is through the square holes in the bleach funnel area overstretched, washer operation will be affected. and push the tabs downward. Refer to Figure 33. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
- Page 54 Lift transmission assembly straight up and out remove pressure hose from retainer clips on of balance ring and upper bearing. outer tub cover. Refer to Figure 32. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
- Page 55 While holding transmission by cover end, gently tap each of the three remaining screws until two halves separate. Place assembly back into vise (cover end up) and remove three screws and lockwashers. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
- Page 56 Shaft Gear (Input) Identification Groove Agitator Pinion Dowel Rack Slide Dowel Screw Transmission Cover Assembly Loctite (Use as a sealant between Transmission Case and Cover.) Figure 46 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
- Page 57 IMPORTANT: End of shaft with identification groove, refer to Figure 46, must be facing outward. This is the end that will mate with the helix. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
-
Page 58: Balance Ring
Refer to Figure 42. c. Lift complete pivot dome (with drive pulley, brake assembly, lower bearing housing, transmission assembly, and balance ring attached) off outer tub. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 59: Snubber Pads
NOTE: Springs must be hooked into the top of the with fluffed side against the base dome and two notches. Refer to Figure 50. make sure pads are equally spaced. Refer to Figure 48. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... - Page 60 Reconnect washer power cord and open water supply valves. NOTE: Washer must be run through a complete cycle to make sure it is operating properly. Centering Spring Figure 50 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
- Page 61 Wire harness Pulley must be installed ahead of spring. Drive Idler Belt Lever Helper Spring Motor Attaching Back Screws Hole Idler Hook Spring Spring Here Figure 51 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
-
Page 62: Section 6 - Adjustments
(to prevent damage to washer components). DO NOT slide washer across floor once the leveling legs have been extended, as legs and base could become damaged. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 63: Pressure Switch
3/4 of a turn in either direction as the switch Attaching may be damaged and flooding could result. Screws Adjusting Screw Rotary Pressure Switch Adjusting Screw Pump Belt Figure 54 Slide Pressure Switch Figure 53 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 64: Out-Of-Balance Switch
The springs are positioned in the upper notch at the factory. Refer to Figure 57. Centering Spring Figure 57 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 65: Section 7 - Test Procedures
Continuity (K & G) OPEN Blue to Red OPEN Continuity (K & F) Red to Yellow Continuity (F & L) OPEN Brown to Yellow OPEN Continuity (G & L) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 66: Motor Check (Start Windings)
Check from brown dot terminal (9) to black wire terminal(s). OPEN CLOSED Defective motor switch. Manually depress centrifugal Replace. switch. CLOSED OPEN Defective switch. Replace. Centrifugal switch OK. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 67: Motor Check (High And Low Windings)
* Do not confuse the white wire coming from the wire harness to the white dot on the motor switch with the white wire coming from the motor to the “B” terminal. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 68: Section 8 - Service Procedures Unique To The Electronic Control Model Washers
To reduce the risk of an electric shock, washer. serious injury, death or fire, DO NOT use an W028 extension cord or an adapter to connect washer to electrical power source. W169 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 69: Grounding Instructions
Check with a qualified electrician or service person if you are in doubt as to whether the dryer is properly grounded. W038 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 70: Washer Operation
IMPORTANT: Holding the LOAD SIZE WATER LEVEL control lever in the RESET position can cause flooding of the washer. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 71: Automatic Preprogrammed Cycles
Temperature Time Time Regular Normal Warm Perm Press Normal Warm Delicates Normal Warm Knit Normal Warm Soak Normal Warm 30 (Soak) 10 (Agitate & Spin) Figure 61 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 72: Status Lights
RESET The RESET pad functions the same as the STOP pad. Pressing it once stops the washer, pressing it two times in succession cancels the cycle. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 73: Customizing Preprogrammed Cycles
MORE pad and a number will appear in the display area. Press MORE again and the time will increase by one minute. Refer to Figure 62. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... - Page 74 MEMORY pad. The old memory cycle will be deleted and the new cycle will be memorized in its place. NOTE: The SIGNAL VOLUME and DELAY START cannot be saved in memory. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
- Page 75 DELAY Will Be START option. It will also cancel the entire cycle. NOTE: Rinse the dispenser thoroughly after it has been used to dispense detergent. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
-
Page 76: Troubleshooting Electronic Control
Figure 63 for terminal numbers, connections and to hardware model selected. color coding. 2. When last step in table is finished, routine sequence will repeat. 3. Each output is on for two seconds. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... - Page 77 White (P1) Cold Water Valve Gray (P8) Ground Green (P9) Loading Door Motor Switch Blue (COM) Pink/Blue (N.O.) CONNECTION RELAY AND TRANSFORMER DIAGRAM (ELECTRONIC CONTROL) Figure 63 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
- Page 78 Agitate Agitate Agitate Agitate Warm Rinse Agitate Soak Agitate Knits Agitate Delicates Agitate Perm Press Agitate Regular Agitate Spin Spin Spin * None (All off) Figure 64 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
-
Page 79: Failure Symptoms
1. Is loading door closed? 2. Loading door switch operating properly? 3. Is washer plugged into properly polarized outlet and washer effectively grounded? Refer to Paragraph 58. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 80: Symptom: Flashing Display
“P1” (neutral) with the loading Inspect loading door switch. door closed, and zero Volts between “N.O.” and “P1” with the loading door open. Recheck troubleshooting sequence. If problem persists, replace control. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 81: Symptom: Indicator Led's Will Not Light When Select Pad Is Pressed
Correct wiring wiring? Recheck troubleshooting sequence. If problem persists, replace control. * For precision, this measurement must be taken with a digital multi-meter set on 200 Ohm scale. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 82: Symptom: Tripped Circuit Breaker Or Blown Fuse
Recheck troubleshooting sequence. If problem persists, replace control. * For precision, this measurement must be taken with a digital multi-meter set on 200 Ohm scale. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 83: Symptom: Washer Will Not Fill Or Wrong Temperature Fill
Use water fill and only cold water relay “K5 ” will be ADVANCE TIMER pad to advance cycle to SPIN if energized for cold water fill. necessary. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 84: Symptom: Washer Will Not Agitate Properly
“P1” (neutral) on control? Motor Relay K2 Replace control. Zero Volts between terminal “P3” (START/SPIN) and “P1” (neutral) on control? Problem not related to electronic control. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 85: Symptom: Washer Will Not Spin Properly
(START/SPIN) and “P1” (neutral) on control? Motor Relay K1 Zero Volts between terminals “P2” Replace control. (START/AGITATE) and “P1” (neutral) on control? Problem is not related to electronic control. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 86: Timer No. 31238 Cycle Sequence
360.00 *ON SINGLE SPEED MODEL WASHERS, ALL SPEEDS ARE FAST. KEY: H = HOT W = WARM C = COLD TIMER NO. 31238 CYCLE SEQUENCE (TWO CYCLE) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 87: Timer No. 31239 Cycle Sequence
360.00 *ON SINGLE SPEED MODEL WASHERS, ALL SPEEDS ARE FAST. KEY: H = HOT W = WARM C = COLD TIMER NO. 31239 CYCLE SEQUENCE (THREE CYCLE) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 88: Timer No. 31240 Cycle Sequence
*ON SINGLE SPEED MODEL WASHERS, ALL SPEEDS ARE FAST. †SOAK IS “INFINITE.” PREWASH IS 24:37 PLUS FILL. KEY: H = HOT W = WARM C = COLD TIMER NO. 31240 CYCLE SEQUENCE (FIVE CYCLE) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 89: Timer No. 32039 Cycle Sequence
5.96 *ON SINGLE SPEED MODEL WASHERS, ALL SPEEDS ARE FAST. KEY: H = HOT W = WARM C = COLD TIMER NO. 32039 CYCLE SEQUENCE (FOUR CYCLE) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 90: Timer No. 32228 Cycle Sequence
*ON SINGLE SPEED MODEL WASHERS, ALL SPEEDS ARE FAST. †SOAK IS “INFINITE”. PREWASH IS 34:37 PLUS FILL. KEY: H = HOT W = WARM C = COLD TIMER NO. 32228 CYCLE SEQUENCE (FIVE CYCLE) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 91: Electronic Control Nos. 31305 Or 33927P Cycle Sequence (Four Cycle)
** THIS TIME WILL BE 3:00 WHEN EXTRA RINSE IS SELECTED. SPIN 5:00 KEY: H = HOT W = WARM C = COLD ELECTRONIC CONTROL NOS. 31305 OR 33927P CYCLE SEQUENCE (FOUR CYCLE) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 92: Electronic Control Nos. 31304P, 31307 Or 33925P Cycle Sequence (Five Cycle)
† 0 to 9 hours FILL H,W,C Variable AGITATE 5:00 PAUSE (SOAK) † 15:00 - 85:00 SPIN 4:00 ELECTRONIC CONTROL NOS. 31304P, 31307 OR 33925P CYCLE SEQUENCE (FIVE CYCLE) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 93: Section 10 - Internal Wiring Of Washer Motor Switch
(High Speed) (High Speed) 4 Pole Auxiliary 4 Pole Auxiliary (Start Winding) (Start Winding) External Wires External Wires Emerson General Electric 27658P MOTOR ASSEMBLY (1 SPEED MOTORS) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... - Page 94 (High Speed) (High Speed) 4 Pole Auxiliary 4 Pole Auxiliary (Start Winding) (Start Winding) External Wires External Wires General Electric Emerson 27179P MOTOR ASSEMBLY (2 SPEED MOTORS) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...
-
Page 95: Section 11 - Wiring Diagrams
W030 WIRING DIAGRAMS AND SCHEMATICS FOUND ON THE FOLLOWING PAGES ARE FOR MODELS COVERED IN THIS MANUAL. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 96: Models Aa9431, Na8831, Aa8431, Awe951, Awe931 And Awe852
Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS AA9431, NA8831, AA8431, AWE951, AWE931 and AWE852 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 97: Models Na6821 And Aa6421
Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS NA6821 and AA6421 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 98: Models Aa5421, Aa5420 And Na4821
Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS AA5421, AA5420 and NA4821 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 99: Models Aa4411, Aa4410, Na3812, Awm352, Awm351, Awm332 And Awm331
Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS AA4411, AA4410, NA3812, AWM352, AWM351, AWM332 and AWM331 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 100: Models Aa3410, Awm250 And Awm230
Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS AA3410, AWM250 and AWM230 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 101: Models Awm651 And Awm631
Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS AWM651 and AWM631 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 102: Models Awm551 And Awm531
Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS AWM551 AND AWM531 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711... -
Page 103: Models Awm452 And Awm432
Failure to install, maintain, and/or operate this machine according to the manufacturer's instructions may result in conditions which can produce bodily injury and/or property damage. W030 MODELS AWM452 and AWM432 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 33711...