Proper Use; Technical Data - EINHELL 43.106.25 Operating Instructions Manual

3. Proper use

The slide is suitable for use with the bench-type
circular saws recommended by the manufacturer.
The equipment is allowed to be used only for its
prescribed purpose. Any other use is deemed to
be a case of misuse. The user/operator and not
the manufacturer will be liable for any damage or
injuries of any kind resulting from such misuse.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
equipment is used in commercial, trade or indust-
rial businesses or for equivalent purposes.
To use the equipment properly you must also
observe the safety information, the assembly
instructions and the operating instructions to be
found in this manual.
All persons who use and service the equipment
have to be acquainted with these operating
instructions and must be informed about the
equipment's potential hazards. It is also imperati-
ve to observe the accident prevention regulations
in force in your area. The same applies for the
general rules of health and safety at work.
The manufacturer will not be liable for any chan-
ges made to the equipment nor for any damage
resulting from such changes. Even when the
equipment is used as prescribed it is still impossi-
ble to eliminate certain residual risk factors.
The following hazards may arise in connection
with the machine's construction and design:
•
Contact with the saw blade in the uncovered
saw zone.
•
Reaching into the running saw blade (cut
injuries).
•
Kick-back of workpieces and parts of work-
pieces.
•
Saw blade fracturing.
•
Catapulting of faulty carbide tips from the saw
blade.
•
Damage to hearing if essential ear-muffs are
not used.
•
Harmful emissions of wood dust when used
in closed rooms.
Anl_Schiebeschlitten_SPK7.indb 14 Anl_Schiebeschlitten_SPK7.indb 14
GB

4. Technical data

Weight of slide : ................................ approx. 6 kg
5. Assembly
Caution! Always screw together the connections
which have self-locking nuts by turning the hex
screw while holding the self–locking nut fi rmly to
fasten tightly.
Fitting the accessory slide (Fig. 1, 2, 3-10)
•
On the bench-type circular saw: Remove the
guide rail for the universal stop.
•
Assemble the slide as shown in Figs. 3-10. In
doing so, make sure that both spacers (110)
are inserted between the profile (115) and
the slide plate (100). Allen key: Not supplied –
available at retail stores.
•
Important: Do not screw the screw (108) in
too tightly. The stop must remain free moving
on the plate for the purposes of angle adjust-
ment.
•
The clamping lever (104) must be mounted in
such a way that the stop can be moved when
the clamping lever is released and is locked
when the clamping lever is secured. During
assembly, make sure that the spring washer
(114) is placed between the self-locking nut
(121) and the washer (123) (Fig. 7).
•
Screw the angles (103, 105) and struts (106,
107) to the bench-type circular saw (Fig. 8).
•
Place the slide on the guide rail (102) from
the front (Fig. 9).
•
If there is any slackness between the guide
rail and the running bearings of the slide pla-
te, then the lower bearing must be adjusted
using the screw (A), so that the slide can
glide freely.
•
Fit the Allen screws (111) to the front and rear
of the rail (102) together with the button (113)
and washer (117) (Fig. 10); they serve as a
limit stop.
•
The stop rail must move parallel to the saw
table at a distance of 1 mm. To achieve this,
loosely tighten the screws for the angles (103,
105) and struts (106, 107), then adjust the
rail in such a way that there is a 1mm gap
between the rail and the saw table in every
position. Now re-tighten the mountings.
•
Please note that for technical reasons relating
to delivery, some loose screws/washers may
be left over even if the slide is assembled
- 14 -
29.04.14 17:06 29.04.14 17:06