Festo CPV DI01 Series Brief Description
Valve terminal with direct connection
Hide thumbs
Also See for CPV DI01 Series:
- Electronic manual (187 pages) ,
- Manual (200 pages) ,
- User instructions (62 pages)
Related Manuals for Festo CPV DI01 Series
Summary of Contents for Festo CPV DI01 Series
- Page 1 Compact Performance Brief description CPV valve termi nal with direct connection type CPV..-DI01 – English 8080242 2017-11c [8080235]...
- Page 2 Translation of the original instructions Documentation on the product For all available product documentation è www.festo.com/pk Copyright: Festo SE & Co. KG Ruiter Straße 82 73734 Esslingen Germany Internet: http://www.festo.com E-Mail: service_international@festo.com Reproduction, distribution or sale of this document or communication of its contents to others without express authorization is prohibited.
- Page 3 (CPV Direct) is intended exclusively for use as a slave on one of the following protocols: – PROFIBUS-DP (as per EN 50170), Festo field bus, ABB CS31, Moeller SUCOnet K. The limit values stated in the section “Technical specifica tions” must be observed here. Detailed information can be found in the Pneumatics manual P.BE-CP-DI01-..
- Page 4 Pin assignment of power supply connection M12 connection Pin no. 1. 24 V DC operating voltage for electronics and inputs 2. 24 V DC load voltage for valves 3. 0 V 4. Earth connection On the extension connection of connected modules Festo 2017-11c English...
- Page 5 CS31 Pin 3 (B) RxD/TxD-P Bus-1 Pin 8 (A) RxD/TxD-N Bus-2 Housing Screening/shield (Cable clip) In brackets: Connection on Festo Sub-D plug type FBS-SUB-9-GS-9 (TN 18529) Detailed information can be found in the manual P.BE-CP-DI01-.. . Festo 2017-11c English...
- Page 6 CP system, field bus address/ station number, diagnostic mode (only PROFIBUS or ABB CS31), baud rate (only Festo field bus). 4. Refit the switch module. 5. If the CP system is the first or last slave in a field bus segment, the terminating resistor in the Festo Sub-D plug must be activated.
- Page 7 DIL switch 4.1 Setting the field bus protocol (4-element DIL switch) PROFIBUS-DP Festo field ABB CS31 SUCOnet K 4.2 Setting the extension of the CP system (4-element DIL switch) Extension to the CP system Setting the DIL switches CPV Direct without extension CPV Direct extended with: –...
- Page 8 4.3 Setting the station number (8-element DIL switch) – PROFIBUS-DP, ABB CS31, SUCOnet K: 8-element DIL switch, switch elements 1...7 – Festo field bus 8-element DIL switch, switch elements 1...6 Coded entry Example: Station number 38 2 + 4 + 32 =...
- Page 9 – PROFIBUS-DP Device-related diagnosis active/inactive – ABB CS31 Load voltage monitoring active/inactive Diagnosis ON Diagnosis OFF 4.5 Set the field bus baud rate (only Festo field bus, 8-element DIL switch) 31.25 kBaud 62.5 kBaud 187.5 kBaud 375 kBaud The CPV Direct has automatic baud rate recognition for all other protocols.
- Page 10 – higher-value address = pilot solenoid 12. 2. CP valve terminals, electric input or output modules on the extension string each occupy 16 input or output addresses. Details and examples of addressing the CP system can be found in the manual P.BE-CP-DI01-.. . Festo 2017-11c English...
-
Page 11: Technical Specifications
Elektromagnetic compatibility – Interference emitted Tested as per DIN EN 61000-6-4 (industry) – Immunity against interference Tested as per DIN EN 61000-6-2 (industry) The component is intended for industrial use. Festo 2017-11c English... - Page 12 “CP pneumatics” Residual ripple 4 Vpp (within tolerance) Electrical isolation Bus interface opto-decoupled Valves See Pneumatics manual P.BE-CPV-.. Detailed information on the CPV Direct DI01 can be found in the manual P.BE-CP-DI01-.. . Festo 2017-11c English...