ATE YOUR PROJECTOR. SAVE THIS USER’S GUIDE FOR FUTURE REF- ERENCE . Safety Instructions Read this user’s guide before you operate your projector and save it for future reference. The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement.
(iii) the model and serial number of the Product. When sending your unit in for repair, please ship your unit in its original packing material or a Boxlight approved ATA Shipping Case, or have a professional packaging company pack the unit.
LIMITATION OF LIABILITY IT IS UNDERSTOOD AND AGREED THAT BOXLIGHT'S LIABILITY WHETHER IN CON- TRACT, IN TORT, UNDER ANY WARRANTY, IN NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE RETURN OF THE AMOUNT OF THE PURCHASE PRICE PAID BY PURCHASER AND UNDER NO CIRCUMSTANCES SHALL BOXLIGHT BE LIA- BLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOST PROFITS, LOST REVENUES OR LOST SAVINGS.
BOXLIGHT CD-725c User’s Guide Shipping Contents The Projector is shipped with the cables required for connection to standard PC or laptop computers. Carefully unpack and verify that you have all the items shown below. If any of these items are missing, please contact personnel at the place of purchase.
IR remote sensor Ventilation grill Speaker Projection lens adjuster RGB signal input RGB signal output connector BOXLIGHT CD-725c User’s Guide 10 11 14 15 Audio/ Video connector Audio jack USB mouse connector S-Video jack RS 232 control port Rear adjuster feet...
BOXLIGHT CD-725c User’s Guide External Control Panel Power Presses the Power key to turn the projector on or off. Auto Automatically determines the best picture settings for current received signals. Left/ Keystone - Right/ Keystone + Menu will display the menu system on screen.
Adjuster The projector is equipped with 2 quick-release adjuster feet. Push the buttons to adjust its tilt angle. Lift the projector up and press the adjuster button to release the adjuster. The adjuster will drop into position and be locked.
BOXLIGHT CD-725c User’s Guide Remote Control Description The remote control sensors are located in the front/ back of the projector. The distance between the sensor and the remote control should not exceed 6 meters (20 feet). Power Menu 3 Left/ Keystone -...
Avoid excessive heat and humidity. There may be danger of an explosion if batteries are incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries accord- ing to the manufacturer’s instructions. BOXLIGHT CD-725c User’s Guide Install batteries as indicated by the diagram inside the compartment.
BOXLIGHT CD-725c User’s Guide INSTALLATION Screen Size Place the projector at the required distance from the screen according to the desired picture size (see the table below). Screen Size (Max.) cm/in Diagonal 30.4/12 60.8/24 91.2/36 121.5/48 151.9/60 182.3/72 213.1/84 243.1/96 273.5108...
Page 15
Connecting to Various Equipment It only takes a few seconds to connect your projector to your desktop or notebook computer, VCR, or other systems. However, a Mac adapter (an optional accessory) is needed for connection to Macintosh computers. Monitor PC Audio...
BOXLIGHT CD-725c User’s Guide OPERATION Start Up Plug the power cord into a wall socket. Turn on the main power switch. Press POWER to start the unit. The back-lit POWER key flashes green and stays green when the power is turned on.
To correct this, press KEYSTONE +/- (hot key) on the control panel of the projector or on the remote control, and then adjust the sliding bar labeled Keystone, as needed. Press + to correct keystoning at the top of the image. Press - to correct keystoning at the bottom of the image.
BOXLIGHT CD-725c User’s Guide Source Selection When several input sources are available, press the SOURCE key to make a selection from the control panel of the projector or the remote control. Projector Auto Menu System Press Menu for the main menu, and then press Menu again to select items in the sub-menu.
BOXLIGHT CD-725c User’s Guide 1. Display Menu FUNCTION DESCRIPTION Corrects any keystoning of the image. Keystone Adjusts the brightness of the image. Brightness Adjusts the degree of difference between dark and light in the image. Contrast Adjusts to avoid the occurrence of flicker.
BOXLIGHT CD-725c User’s Guide 2. Image Menu FUNCTION Users have 3 options for the image ratio. Ratio Adjusts the horizontal position of the projected image. H-position Adjusts the vertical positon of the projected image. V-position Adjusts the color temperature to fit your preference.
User logo Enables the user to define the logo screen that will display dur- ing start-up. Three modes are available: Default (BOXLIGHT logo), black screen and blue screen. Returns all settings to their factory preset values. Default Selects video mode.
Increases or decreases the color range (R, G, B) of the image. Adjusts the image to make it appear more red or blue. Adjusts the image to make it appear sharper or softer Selects PIP image systems: Auto, NTSC, PAL, SECAM BOXLIGHT CD-725c User’s Guide PIP image PIP image PIP image...
Please do not unplug the power cord before POWER is shut down or during the two-minute cooling process. If the projector is not properly shut down, to protect the lamp, the sys- tem will detect this and cool the lamp for two minutes automatically before turning on again.
The LAMP indicator will light up if the lamp becomes too hot. Turn off the power and let the projector cool for 45 minutes. If the LAMP indicator is still red when turning the power on, please contact BOXLIGHT Technical Sup- port at 1-800-762-5757 or +1-360-779-7901.
BOXLIGHT CD-725c User’s Guide Lamp Replacement Caution To reduce the risk of electrical shock, always turn off the projector and dis- connect the power cord before changing the lamp. Press the POWER button to switch off the projector. Disconnect the power cord from the outlet and the projector.
Caution To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp. To reduce the risk of injuries to fingers and damage to internal components, use caution when removing lamp glass that has shattered into sharp pieces.
Description of parts Mac adapter (switchable) 210W lamp module Ordering Parts or Getting Information For product information, product assistance, service information, or to order accessories, please contact BOXLIGHT corporation at 1-800-762-5757 or +1-360- 779-7901 or visit the web site at www.boxlight.com. Maintenance...
Select the correct video system. Adjust brightness, contrast, or saturation. Press Auto on the control panel of the projector or the remote control unit to get better picture quality. Adjust the focus. Reposition the unit to improve its projection angle.
20 hours. The lamp has been in operation for over 1500 hours. The warning message will display for 30 seconds every 5 min- utes after you turn on the projector and the power will turn off automatically after 10 minutes.
Need help?
Do you have a question about the CD-725c and is the answer not in the manual?
Questions and answers