Related Manuals for Frontier BB2272
Summary of Contents for Frontier BB2272
-
Page 1: Tractor Hitch Class
O P E R A T O R ’ S M A N U A L BOX BLADES BB2272 BB2284 5WPMAN0266 (Rev. 2/16/2009) -
Page 2: Introduction
Use only genuine Frontier service parts. Substitute parts will void the warranty and may not meet standards required for safe and satisfactory operation. Record the model number and serial number of your equipment in the spaces... -
Page 3: Table Of Contents
SPECIFICATIONS BB2272 BB2284 Width ....... . . 73 in. (1854.2 mm) 85 in. -
Page 4: Safety Rules
Power unit must be equipped with ROPS or Keep bystanders away from equipment. ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death (Safety Rules continued on next page) 4 Safety Landscape Frontier SR (Rev. 12/4/2006) - Page 5 Block equipment securely for storage. Before leaving operator's seat, lower lift arms Keep children and bystanders away from stor- and put attachment on the ground. Engage brake, stop engine, remove key, and remove seat belt. age area. Safety 5 Landscape Frontier SR (Rev. 12/4/2006)
-
Page 6: Safety Decals
SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 1 - Serial Number Plate PRODUCT IDENTIFICATION NUMBER LENEXA, KS, U.S.A. LENEXA, KS, U.S.A. 3 - 5WP1003751 2 - 5WP1002423 WARNING WARNING TO AVOID SERIOUS INJURY OR DEATH: Read Operator's Manual before operating, servicing or repairing equipment. -
Page 7: Dealer Check Lists
SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! (Safety Decals continued from previous page) WARNING FALLING OFF CAN RESULT IN BEING RUN OVER. Tractor must be equipped with ROPS (or ROPS CAB) and seat belt. -
Page 8: Operation
OPERATION The operator is responsible for the safe operation of ___ Check that all hardware is properly installed and secured. this equipment. The operator must be properly trained. Operators should be familiar with the equipment, the ___ Do not allow riders. tractor, and all safety practices before starting opera- tion. - Page 9 Category 2 Standard 2. Slide lower sleeve 5WP1003830 (sold separately) (Figure 2) over the mounting pin supplied with box blade. Re- 1. Attach the tractor's lower lift arms to the box blade install lynch pins. through the lower, outer set of holes. 3.
-
Page 10: Storage
BACKFILLING 3. Drive forward with the box blade in this position and loose material will be leveled. 1. Raise or remove scarifier shanks. STORAGE 2. Lower the blade to the ground and back up into the fill material. ARNING 3. Shorten the top link to raise the cutting blade and control how much the blade digs in. -
Page 11: Owner Service 11
OWNER SERVICE The information in this section is written for operators who possess basic mechanical skills. If you need help, your dealer has trained service technicians available. For your protection, read and follow the safety informa- tion in this manual. ARNING NEVER GO UNDERNEATH EQUIPMENT. - Page 12 REPLACING SCARIFIER TOOTH 3. Attach cutting edge to box blade and secure with plow bolts and hex nuts previously removed. 4. Torque plow bolts to 170 lbs-ft. See specifications given in Bolt Torque Chart, page 14. 1. Shank 2. Tooth CLEANING 3.
-
Page 13: Parts List
BB2272 / BB2284 PARTS LIST 23 – COMPLETE DECAL SET 24 – SAFETY DECAL SET LOCK BAR CHART QUANTITY PER UNIT Part Number BB2272 BB2284 5WP1003797 5WP1003798 PART DESCRIPTION PART DESCRIPTION 5WP1003887 WA 72" Tailgate 15 5WPR34B15P A/R Double notch point/shank asy 5WP1003820 WA 84"... -
Page 14: Bolt Torque Chart
BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly. -
Page 15: Bolt Size Chart & Abbreviations
BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE Bolt Thread Sizes 5/16 Metric Bolt Thread Sizes 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS AG .............. Agriculture MPa............Mega Pascal ASABE.... - Page 16 ©2003 Woods Equipment Company. All rights reserved. WOODS and the Woods logo are trademarks of Woods Equipment Company. Frontier Equipment and the Frontier logo are trademarks of Deere & Company. All other trademarks, trade names, or service marks that appear in this...