Related Manuals for Frontier DH1380
Summary of Contents for Frontier DH1380
- Page 1 O P E R A T O R ' S M A N U A L DISK HARROWS DH1376 DH1380 DH1396 DH13_5TL15193_7/10/2014...
-
Page 2: Introduction Ii
Use only genuine Frontier service parts. Substitute parts will void the warranty and may not meet stan- dards required for safe and satisfactory operation. Record the model number and serial number of your... -
Page 3: Table Of Contents
TABLE OF CONTENTS INTRODUCTION ..........ii SPECIFICATIONS / GENERAL INFORMATION . -
Page 4: Specifications / General Information
SPECIFICATIONS DH1380 DH1396 DH1396 DH1376 3-Point Hitch Category 1 and 2 Category 1 and 2 Category 1 and 2 Category 1 and 2 (iMatch Compatible) (iMatch Compatible) (iMatch Compatible) (iMatch Compatible) Working Width 76" 80" 96" 96" Blade Spacing 9"... -
Page 5: Safety Decals 2
SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH Replace Decals Immediately If Damaged! 5TL15194A Check that all safety decals are installed and in good condition. 5TL15194B Replace if decals are worn or damaged. - Page 6 SAFETY REFLECTOR DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH Replace Decals Immediately If Damaged! DH1376 and DH1380 Reflector Decals 4 1/2” RED REFLECTORS 5TL15240 Check that all reflector decals are installed and in good condition.
-
Page 7: Safety Rules 4
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Safety is a primary concern in the design and rough-soled work shoes and protective equip- manufacture of our products. Unfortunately, our ment for eyes, hair, hands, hearing, and head; efforts to provide safe equipment can be wiped and respirator or filter mask where appropri- out by an operator’s single careless act. - Page 8 SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! OPERATION (cont’d) moveable parts even when the engine has • Use extreme care and reduce ground speed been turned off. Hydraulic system leak down, on slopes and rough terrain. hydraulic system failures, mechanical failures, •...
- Page 9 SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! MAINTENANCE(cont’d) • Tighten all bolts, nuts, and screws to torque chart specifications. Check that all cotter pins • Make sure attachment is properly secured, are installed securely to ensure equipment is in adjusted, and in good operating condition.
-
Page 10: Dealer Instructions
The following check list is a reminder of points to inspect. ____ Complete the Warranty Registration locat- Check off each item if it is found satisfactory or ed on the Frontier website. 7 Dealer Instructions... -
Page 11: Operation 8
Operation Safety is a primary concern in the design and system leak down, hydraulic system failures, manufacture of our products. Unfortunately, our mechanical failures, or movement of control efforts to provide safe equipment can be wiped levers can cause equipment to drop or rotate out by an operator’s single careless act. - Page 12 Adjusting Gang Angles adjustment. Remember each adjustment affects another; therefore, extreme care should be used when adjusting. CAUTION Each trial run should be made with the tractor in When making gang adjustments, be careful to the same gear and approximately the same keep hands and feet clear of sliding parts and RPM.
-
Page 13: Trouble Shooting 10
Gang Adjustment Trouble Shooting 1. Unit not tracking or is fishtailing A. Adjust top link to increase weight on the rear of the disc B. Disc assembled incorrectly. Refer to assem- bly instructions. 2. Unit not tracking: skipping, jumping, and A. -
Page 14: Owner Service
Owner Service Gang Assembly for Maintenance WARNING WARNING • NEVER GO UNDERNEATH EQUIPMENT. • When performing maintenance or repairs make Never place any part of the body underneath sure the equipment is in the lowered position equipment or between moveable parts even and both the mainframe and gangs are properly when the engine has been turned off. -
Page 15: Parts Catalog 12
Figure 1 Set of Lower Hitch Bushings for iMatch (Sold Separately) Parts Catalog 12... - Page 16 LYNCH PIN 5TL14629 FRONT GANG BEAM 4" X 3" X 30" MODEL DH1376 5TL 14630 FRONT GANG BEAM 4" X 3" X 33" MODEL DH1380 5TL14631 FRONT GANG BEAM 4" X 3" X 37" MODEL DH1396 5TL14974 FRONT GANG BEAM 4" X 3" X 41"...
- Page 17 MODEL DH1376 DECAL(NOT SHOWN) 5TL15224 MODEL DH1380 DECAL(NOT SHOWN) 5TL15225 MODEL DH1396 DECAL(NOT SHOWN) 5TL15195 2 1/2” FRONTIER LOGO DECAL (NOT SHOWN) 5TL15193 DH13 OPERATOR’S MANUAL (NOT SHOWN) 5TL15240 4 1/2” RED REFLECTOR(NOT SHOWN) 5TL15199 9” RED REFLECTOR,Model DH1396(NOT SHOWN) 5TL15200 9”...
-
Page 18: Optional Equipment
MODEL DH1276 MODEL DH1280 5TL14981 HEAVY SCRAPER BAR, 30" MODEL DH1376 5TLT261 HEAVY SCRAPER BAR, 33" MODEL DH1280 MODEL DH1280 MODEL DH1380 5TL12338 HEAVY SCRAPER BAR, 37" MODEL DH1296 MODEL DH1396 5TL11738 HEAVY SCRAPER BAR, 40" MODEL DH1296 5TLT262 HEAVY SCRAPER BAR, 41"... - Page 19 Heavy Scraper Kit Mounting Instructions *NOTE- When attaching heavy scraper kit, do 2-hole clamp (ref. #12) on top of scraper bar (ref. NOT tighten any hardware until stated in direc- #13) and fasten together with 1/2" x2 1/2 GR 2 tions.
- Page 20 Optional Equipment Con’t. Center Sweep Kit Figure 3 DH13Series 5TL11476 Ref.# Part # Description 5TL10601 SHANK BRACKET 3" BEAM MODEL DH11, DH12 5TL10388 SHANK BRACKET 4" BEAM MODEL DH13 5TL10599 SHANK HOLDER 3" BEAM MODEL DH11, DH12 5TL9175 SHANK HOLDER 4" BEAM MODEL DH13 5TL10602 BALK BREAKER SHANK...
- Page 21 Optional Equipment Con’t. Outrigger Kit Figure 4 DH13 Series 5TLT70318 (Includes all parts for assembly) Ref.# Part # Description 5TL12163 HEX BOLT, " GR. 5 2” 5TLTOR2 OUTRIGGER HALF 5TLTOR1 OUTRIGGER WASHER, 1 1/8" *Note 5TLT26 HEX NUT, " 5TLT25 LOCK WASHER, 1/2"...
-
Page 22: Bolt Size And Bolt Torque Chart
Bolt Size Chart SAE Torque Chart DH13 Series gang bolt torque 795 lbs-ft 1080 N-m 19 Bolt Size and Bolt Torque Chart... -
Page 23: Notes 20
Notes Notes 20... - Page 24 PART NO. 5TL15193 © 2014 Monroe Tufline Manufacturing, Inc. All Rights Reserved...