Use only genuine Frontier service parts. Substitute parts will void the warranty and may not meet stan- dards required for safe and satisfactory operation. Record the model number and serial number of your...
GENERAL INFORMATION The purpose of this manual is to assist you your particular situation. in operating and maintaining your Offset The illustrations and data used in this Disc Harrow. Read it carefully. It furnishes manual were current at the time of print- information and instructions that will help ing.
5TL14996 Check that all reflector decals are installed and in good condition. Replace if decals are worn or damaged. Only the DH3499 and DH3409 have (2) 2” x 9” yellow reflective decals. 2" x 9” Yellow Reflectors 5TL15200 2' X 9” Red...
SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH Replace Decals Immediately If Damaged! Check that all safety decals are installed and in good condition. Replace if decals are worn or damaged.
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Safety is a primary concern in the design and rough-soled work shoes and protective equip- manufacture of our products. Unfortunately, our ment for eyes, hair, hands, hearing, and head; efforts to provide safe equipment can be wiped and respirator or filter mask where appropri- out by an operator’s single careless act.
Page 9
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! OPERATION (cont’d) moveable parts even when the engine has • Use extreme care and reduce ground speed been turned off. Hydraulic system leak down, on slopes and rough terrain. hydraulic system failures, mechanical failures, •...
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! MAINTENANCE(cont’d) • Tighten all bolts, nuts, and screws to torque chart specifications on page 19. Check that all • Make sure attachment is properly secured, cotter pins are installed securely to ensure adjusted, and in good operating condition.
____ Show customer the safe, proper procedures to ____ Complete the Warranty Registration located on be used when mounting, dismounting, and storing the Frontier website. equipment. Dealer Instructions 8...
Pre-Assembly Photo 3 The DH34 is shipped from the factory unassem- bled. The numbers referenced below are from the DH34 parts catalog, Figure 3 on page 14. When assembly is complete tighten all bolts according to the torque and bolt chart on page 19. Remove the bag from the pallet which contains the u-bolts and hardware.
Page 13
DH32 Gang Assembly Figure 1 A - Measurement from the side of the frame to the edge of disc blade. B - Measurement from end of gang beam to center of u-bolt in hanger. #5TLT1001 FRONT & REAR GANG BEAM 5”...
Operation Safety is a primary concern in the design and system leak down, hydraulic system failures, manufacture of our products. Unfortunately, our mechanical failures, or movement of control efforts to provide safe equipment can be wiped levers can cause equipment to drop or rotate out by an operator’s single careless act.
Page 15
Depth Control To adjust the front and rear gang angles, remove the The DH34 leveling system controls the harrow gang angle adjusting bar (ref. #1, figure 2) from the from full depth penetration all the way up to Figure 2 transport height.
Owner Service Gang Assembly for Maintenance WARNING WARNING • NEVER GO UNDERNEATH EQUIPMENT. • When performing maintenance or repairs make Never place any part of the body underneath sure the equipment is in the lowered position equipment or between moveable parts even and both the mainframe and gangs are properly when the engine has been turned off.
Page 18
5TLT1001 GANG BEAM, 5"X3"X 63" (DH3474) 5TL11686 GANG BEAM, 5"X3"X 72" (DH3480) 5TLT1003 GANG BEAM, 5"X3"X 81" (DH3490) 5TLT1005 GANG BEAM, 5"X3"X 90" (DH3499) 5TLT1007 GANG BEAM, 5"X3"X 99" (DH3409) 5TL12271 GANG BEAM PIVOT CLAMP 5TLT727A LOCK NUT, 1 1/2"...
Page 19
5TL15658 3 1/2" FRONTIER LOGO DECAL, NOT SHOWN 5TL15199 9" RED REFLECTOR DECAL, NOT SHOWN 5TL15200 9" YELLOW REFLECTOR DECAL (DH3499 & DH3409 ONLY), NOT SHOWN 5TL15659 "DH34" OPERATORS MANUAL, NOT SHOWN Parts Catalog 16 * M/S - Model Specific...
2- HOLE CLAMP 5TLT2644 HEAVY SCRAPER BAR, 63" (DH3474) 5TL11712 HEAVY SCRAPER BAR, 72" (DH3480) 5TLT2645 HEAVY SCRAPER BAR, 81" (DH3490) 5TLT2647 HEAVY SCRAPER BAR, 90" (DH3499) 5TLT2649 HEAVY SCRAPER BAR, 99" (DH3409) 5TL10151 SCRAPER ARM 5TL11081 UNIVERSAL SCRAPER BLADE 5TL11027 or ARM &...
Heavy Scraper Kit Mounting Instructions *NOTE- When attaching heavy scraper kit, do #13) and fasten together with 1/2" x2 1/2 GR 2 NOT tighten any hardware until stated in direc- bolt(ref. 6) and 1/2” flange locknut (ref. #7). tions. Adjustments may need to be made. Scraper arm &...