Handle Adjustment - Chicco FULLY Instructions For Use Manual

Now fit the fabric lining fastening it to the fabric of the
stroller with the internal zip in the head area and wrap the
elastic part and fasten the buttons in the area of the feet as
described in steps 27-28.
In semi-rigid carrycot configuration, it can be removed
from the stroller when the child is inside it. The hood fea-
tures a tube to be used as a handle for carrying with an
appropriate grip.
31. Before removing the carrycot from the frame, position
the handle vertically (Fig. 31), press the two grey but-
tons on the lateral joints (fig. 31A) and lift the semi-rigid
carrycot holding the handle (fig. 31B).
32. Once the semi-rigid carrycot accommodating your
child is removed from the stroller frame, it can be placed
on a flat surface (Fig. 32).
To return to the stroller or pram configuration, it is neces-
sary to remove the fabric lining and the semi-rigid carrycot
base previously fitted.
To remove the base, repeat the assembly operations previ-
ously described (see point 30) in reverse order.
33. Once removed from the seat, the base can be folded on
itself to make it more compact acting on the two sliding
buttons in the lower part at the same time (Fig. 33).
WARNING: When not in use, keep the plate out of reach
of children.
PARKING BRAKE
The stroller is equipped with a pedal parking brake located
on the rear axle.
34. To engage the parking brake, press one of the two ped-
als down (Fig. 34). To disengage the parking brake, push
one of the two pedals upwards (Fig. 34A).
WARNING: Always apply the brakes whenever the stroller
is stopped. Never leave the stroller on a sloping surface with
your child inside it, even if the parking brake is engaged.
WARNING: After engaging the parking brake, make sure
the brakes are properly enabled on both rear wheels.
SWIVEL WHEELS
The stroller has front swivel/fixed wheels.
It is recommended to use the wheels in the fixed mode on
particularly changeable surfaces. The use of the wheels in
the swivel mode is recommended in order to increase the
control of the stroller on a normal road surface
35. To engage the front swivel wheels, push the front but-
ton downward with your foot (Fig. 35). To engage the
fixed wheels, press the button with your foot once
again. On fixed mode, all the wheels will remain locked
in straight position.
WARNING: Both wheels must always be locked or un-
locked at the same time.

HANDLE ADJUSTMENT

The stroller features a handle that can be adjusted in height.
36. It can be adjusted by pressing the release button locat-
ed on the centre of the handle (Fig. 36).
After switching from one position to the other, make sure
the automatic locking mechanism is properly engaged.
COMFORT KIT
37. Included with the seat is a comfort kit including two
shoulder straps and a crotch strap (Fig. 37).
38. For assembly, insert the shoulder straps (Fig. 38) and the
crotch strap in the relevant padding (Fig. 38A).
LEGCOVER / PRAM APRON
39. This component can be used in two different ways: as
legcover in stroller configuration (Fig. 39) and as an apron
in pram/semi-rigid carrycot configuration (Fig. 39A).
40. In the stroller configuration, lay the cover on the frame
and fasten the two external side buttons (Fig.40). For
greater protection, it is possible to lift the fabric flap of
the cover by fastening it to the slots on the inner sides
of the hood using the buttons (fig.40A).
41. In stroller configuration, insert the leg cover, making
sure that the fabric pocket remains under the legrest/
seat (Fig.41). Then fasten it to the two external side but-
tons (Fig. 41A).
RAIN COVER
42. The stroller is equipped with a rain cover. To secure the
rain cover, completely open the stroller's hood and wrap
the raincover around the external tube of the seat (Fig.
42). After use, hang the rain cover to dry (if it is wet) before
folding and storing it away out of the reach of children.
WARNING: Use the rain cover supplied and mounted on
the hood fully open.
The rain cover cannot be used on the stroller without the
hood; it may represent a suffocation hazard for the child.
WARNING: The rain cover supplied must be used under
the supervision of an adult.
WARNING: The rain cover supplied should only be used
on the Fully stroller.
WARNING: When it is being used, make sure the rain cover
does not come into contact with your child's face.
When the rain cover is fitted on the stroller, never leave it
exposed to direct sunlight with the child inside, as the tem-
perature will rise considerably.
FOLDING THE STROLLER
To fold the stroller, adjust the handle in the lowest position
and leave the front wheels unlocked. It is possible to close
the stroller in two different modes: without the seat or with
the seat fastened to the frame.
Folding the stroller without seat
43. To remove the seat, press the grey buttons located near
the seat's joints (Fig. 43).
44. To close the stroller, slide button 1 and then press but-
tons 2 and 3 at the same time (Fig. 44 - 44A).
Folding the stroller with seat
45. Close the hood using the central button (see point 12
HOOD); then close the seat by pulling the sliding but-
tons behind the seat tube upwards (fig. 45), and push it
forward until it reaches the most compact position (fig.
45A – 45B).
46. Fold the stroller as described in step 44. The stroller is
now folded with the seat fastened to the frame (Fig. 46).
Important Note: The images and instructions in this manual
refer to a single carrycot version. Some of the components
and functions described here may vary depending on the
model purchased.
USE OF ADAPTOR "1"
47. The Fully stroller features adaptors (Fig. 47) to vary the
22