Table of Contents
Advertisement
Quick Links
Please note that Cypress is an Infineon Technologies Company.
The document following this cover page is marked as "Cypress" document as this is the
company that originally developed the product. Please note that Infineon will continue
to offer the product to new and existing customers as part of the Infineon product
portfolio.
Continuity of document content
The fact that Infineon offers the following product as part of the Infineon product
portfolio does not lead to any changes to this document. Future revisions will occur
when appropriate, and any changes will be set out on the document history page.
Continuity of ordering part numbers
Infineon continues to support existing part numbers. Please continue to use the
ordering part numbers listed in the datasheet for ordering.
www.infineon.com
Advertisement
Table of Contents
Related Manuals for Infineon Cypress MB2146-270
Summary of Contents for Infineon Cypress MB2146-270
- Page 1 The document following this cover page is marked as “Cypress” document as this is the company that originally developed the product. Please note that Infineon will continue to offer the product to new and existing customers as part of the Infineon product portfolio.
- Page 2 MB2146-270 MC-8FX Family SOP-28P (1.27 mm pitch) Header Board Operation Guide Doc. # 002-07375 Rev. *A Cypress Semiconductor 198 Champion Court San Jose, CA 95134-1709 Phone (USA): 800.858.1810 Phone (Intnl): +1.408.943.2600 www.cypress.com...
- Page 3 Copyrights Copyrights © Cypress Semiconductor Corporation, 2006-2016. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC (“Cypress”). This document, including any software or firmware included or refer- enced in this document (“Software”), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide.
- Page 4 Preface Thank you for purchasing the SOP-28P (1.27 mm pitch) * header board (Model number : MB2146-270) for the F MC -8FX family. MB2146-270 is a header board used to connect the MCU board (Model number : MB2146-301, MB2146-303) which mounted F MC-8FX family evaluation MCU to a user system.
-
Page 5: Table Of Contents
Contents 1. Product Outline Product outline ......................5 Product configuration ....................6 2. Checking the Delivered Product 3. Handling Precautions 4. Notes on Designing Notes on designing printed circuit board for the user system ........9 5. Procedure for Connection to the User System Connection.........................11 Disconnection ......................11 6. -
Page 6: Product Outline
Product Outline Product outline This product is a header board (referred to as “header board”) used to connect the MCU board (Model number : MB2146-301, MB2146-303) which mounted an evaluation MCU in the F MC-8FX family of Cypress 8-bit microcontrollers to a user system and package product signal line conversion board (referred to as “conversion board”) for connecting with a target board. -
Page 7: Product Configuration
Product Outline Product configuration Table 1-1 lists the product configuration in the header board, and Table 1-2 lists options. Table 1-1. Product Configuration Name Description Remarks The board which changes the signal Header board for SOP-28P line of a package product from a (1.27 mm pitch) package MCU board Capable of purchasing as option... -
Page 8: Checking The Delivered Product
Checking the Delivered Product Before using the MB2146-270, confirm that the following components are included in the box: SOP-28P (1.27 mm pitch) Header board ■ Signal line conversion board for SOP-28P (1.27 mm pitch) * ■ Operation manual (English version, this manual) ■... -
Page 9: Handling Precautions
Handling Precautions Please take note of the following points to ensure that the header board and conversion board are always used correctly in a suitable environment. Do not apply excessive force to the conversion board mounted on the user system when the ■... -
Page 10: Notes On Designing
Notes on Designing Notes on designing printed circuit board for the user system When the header board is connected to the user system, the parts mounted around the conversion board in the user system may be touched the header board if the height of the parts is tall. To prevent this, design the printed circuit board for the user system such that the components do not exceed the height shown in Figure 4-1. - Page 11 Notes on Designing ■ MCU footprint design precautions Figure 4-2 shows the recommended footprint dimensions for the conversion board mounted on the printed circuit board for the user system. Take the footprint in Figure 4-2 into consideration as well as the footprint of the mass production MCU when designing the printed circuit board for the user system.
-
Page 12: Procedure For Connection To The User System
Procedure for Connection to the User System Connection Please mount the supplied conversion board on the user system before using this product. The angle cut linearly at one place only in the conversion board indicates the position of pin 1 of the device. -
Page 13: Product Specifications
Product Specifications General Specifications Table 6-1 lists the general specifications of the header board. Table 6-1. General Specifications Item Description Remarks Operating temperature and 10°C to 35°C (operation) , - 10°C to 50°C (storage) storage temperature Operating humidity and storage 35 % to 85 % (operation and storage) humidity condensation... -
Page 14: Main Parts
Product Specifications Main Parts Table 6-2 lists the main parts of the header board and conversion connector. Table 6-2. Main Parts Part Description 120 pins, 0.5 mm pitch, 2-piece connector (Straight) × 2 MCU board I/F connector [Model number : WR-120SB-VF-N1 (Header board side) (from Japan Aviation Electronics Industry, Ltd.)]... -
Page 15: Function Block Diagram
Product Specifications Function Block Diagram The header board connects to the mass production MCU's pin signals via the MCU board I/F con- nector and the conversion board connected to the target board. The header board does not contain any ICs or other internal components. Figure 6-1 shows the block diagram. Figure 6-1. -
Page 16: Mcu Board I/F Connector(Cn1/Cn2/Cn3)
Product Specifications MCU Board I/F Connector(CN1/CN2/CN3) CN1 and CN2 are MCU board I/F connectors. CN3 is the incorrect insertion prevention socket of the MCU board. The pin assignment of the MCU board I/F connector CN1 is shown in Table 6-3, and the pin assignment of the MCU board I/F connector CN2 is shown in Table 6-4. - Page 17 Product Specifications Table 6-4. Pin assignment of the MCU board I/F connector CN2 Connector Evaluation Connector Evaluation Connector Evaluation Signal Signal Signal MCU Pin MCU Pin MCU Pin name name name Numbers Numbers Numbers Numbers Numbers Numbers SEL0 SEL3 SEL4 SEL1 P04C AVcc3...
-
Page 18: Pin Assignments For I/F Between Header Board And Conversion Board(Connection Table)
Product Specifications Pin assignments for I/F between header board and conversion board(connection table) Table 6-5 lists the pin assignments for I/F between header board and conversion board. Table 6-5. Pin Assignments for I/F between header board and conversion board (Connection Table) Conversion board Matsushita Electric Works Ltd. -
Page 19: Revision History
Revision History Document Revision Document Title: MB2146-270 F MC-8FX Family SOP-28P (1.27 mm pitch) Header Board Operation Guide Document Number: 002-07375 Origin of Revision ECN# Issue Date Description of Change Change 05/30/2006 HUAL Initial release 5280086 05/26/2016 HUAL Migrated Spansion Guide from SS01-26011-1E to Cypress format MB2146-270 F MC-8FX Family SOP-28P (1.27 mm pitch) Header Board Operation Guide, Doc.