Summary of Contents for Infineon Cypress F2MC-8FX Series
Page 1
The document following this cover page is marked as “Cypress” document as this is the company that originally developed the product. Please note that Infineon will continue to offer the product to new and existing customers as part of the Infineon product portfolio.
Page 2
MB2146-401 MC-8FX Family Evaluation Board Operation Guide Doc. # 002-07324 Rev. *A Cypress Semiconductor 198 Champion Court San Jose, CA 95134-1709 Phone (USA): 800.858.1810 Phone (Intnl): +1.408.943.2600 www.cypress.com...
Page 4
Preface Thank you for purchasing the evaluation board (Part number:MB2146-401) for the F MC -8FX family. The MB 2146-401 is a development support tool for developing and evaluating applied products based on the F MC-8FX* family of the 8-bit microcontroller manufactured by Cypress. This manual is intended for engineers who use the MB2146-401(hereafter called the evaluation board)to develop applied products based on Cypress F MC-8FX family of the 8-bit microcontroller.
Page 5
Preface Note that using the product not in the above operating environment may unexpectedly cause personal injury to the user (or another person if present near the product) or physical damage to properties around the product. You should also keep the packaging materials used for shipping the product. They work well as they are when you transport the product again, for example, if it becomes out of order and needs to be repaired.
Page 6
Preface When turning the power on or off, follow the relevant procedure described in this document. Before turning the power on, in particular, be sure to finish making all the required connections. To set up and use the product, follow the instructions given Damage in this document.
Contents 1. Product outline Product composition ....................8 Appearance and part name ..................9 2. Checking the Delivered Product 3. Connecting Attachment of a MCU board / AC adapter ..............11 Note on use .......................12 4. Board Setup/Function Power supply from AC adapter..................13 Power supply from the external power supply input terminal ........13 LED port selection .....................14 Selection of 5 V/3.3 V power supply ................15...
Product outline This product is a development support tool for performing the development and evaluation of an application product which used F MC-8FX family of Cypress 8 bit microcontroller. By connecting the MCU board (Part number : MB 2146-3xx) on which evaluation MCU was mounted, it is the evaluation board which enables verification of the evaluation MCU before user systems development of operation, and development evaluation of a firmware (This board is called henceforth).
Product outline Product composition The product composition of this board is shown in Table 1-1, and an option (sold separately) is shown in Table 1-2. Table 1-1. Product composition Name Part number Description Remarks MC-8FX Evaluation board MB2146-401 Evaluation MCU not built in —...
Product outline Appearance and part name The name and dimensions of the appearance of this board and each part are shown. Figure 1-2. Functional name and dimensions 150 mm LED17 JP6 JP5 LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 LED9 LED10 LED11...
Checking the Delivered Product Before using the Evaluation board,confirm that the following components are included in the box: Evaluation board AC adaputer * Operation manual (Japanese, English (this manual) ) : 1 (part each) *: 3A-211DA-05 (Denshi Tsusho Co., LTD) MB2146-401 F MC-8FX Family Evaluation Board Operation Guide, Doc.
Connecting Attachment of a MCU board / AC adapter Please connect CN1/CN2 of the connection of a MCU board with this board, and this board, and CN1/CN2 of a MCU board.Since the incorrect insertion prevention socket of two pins is mounted in this board and the MCU board by each, please become a diagonal position (refer to Figure 3-1) .
Connecting Figure 3-2. AC adapter connection RESET LVSS LVCC AVSS AVCC POWER LED17 +3.3V AVSS AVCC POWER JP6 JP5 LED 1 P00C P01C LED 2 LED 3 P02C LED 4 P03C P04C LED 5 CAP. LED 6 P05C LED 7 P06C P07C LED 8...
Board Setup/Function Power supply from AC adapter When supplying the power supply from AC adapter, TP2 (VCC) and TP3 (VSS) of the terminal for an external power supply input should presuppose that it is open of it. Moreover, they must not supply an external power supply.
Board Setup/Function LED port selection It is decided whether a light emitting diode connection change jumper plug (JP1/JP2) connects the light emitting diode port on this board to each port of the evaluation MCU carried on the MCU board, or it does not carry out. When using a Light Emitting Diode port,an attached jumper plug is connected to this board.
Board Setup/Function Selection of 5 V/3.3 V power supply The details of a setup of 5 V/3.3 V power supply jumper plug selection (JP3/JP4) are shown in Table 4-3. When you supply the power supply from the external power supply input terminals TP2 (VCC) and TP3 (VSS), please open the power supply selection jumper plug (JP3/JP4) of 5 V/3.3 V.
Board Setup/Function Selection of the supply level to the MOD terminal of evaluation The supply level to the mode terminal (MOD) of Evaluation MCU carried in the MCU board is chosen with an MOD selection jumper plug (JP8). Details are shown in Table 4-4. Be referred to as "short" of a jumper plug, and give an MOD terminal state as an "L level".
Specification General specification The general specification of this board is shown in Table 5-1. Table 5-1. General specification Item Description Operating/storage temperature 5°C to 35°C (at operating) , 0°C to 70°C (at storage) Operating/storage humidity 20 % to 80 % (at operating) , 20 % to 80 % (at storage) Dimensions About 100 mm ×...
Specification Functional block diagram A functional block diagram is shown in Figure. 5-1. Figure 5-1. Functional block diagram EXTERNAL POWER SUPPLY INPUT PIN 5V/3.3V POWER SELECT POWER JUMPER PLUG REGULATER 3.3V AVCC AVCC AVSS AVSS LVCC LVCC LVSS LVSS AVC C VC C AV R VC C AVSS VSS Cpin...
Specification Main component material The main component material of this board is shown in Table 5-2. Table 5-2. Main component material Item Part number Description Manufacture Input power supply : AC100 V - 240 V, 50/60 Hz output power supply : DC5 V, 4 A AC adapter 3A-211DA-05 Plug : Outer diameter = 5.5 mm,...
Specification MCU board I/F connector (CN1/CN2/CN5) CN5 is the incorrect insertion prevention socket of a MCU board. CN1/CN2 are a MCU board I/F connector.The pin assignment of CN1 is shown in Table 5-3, and the pin assignment of CN2 is shown in Table 5-4. Table 5-3.
Page 22
Specification Table 5-4. Pin assignment of MCU board I/F connector CN2 Connector Evaluation Connector Evaluation Connector Evaluation Signal Signal Signal name name name Number Pin No. Number Pin No. Number Pin No. SEL0 SEL3 SEL4 SEL1 P04C AVcc3 P06C AVss P07C...
Specification The I/F connector for extension (CN4) The pin assignment of the I/F connector for extension is shown in Table 5-5. Table 5-6 lists recommended connectors. Table 5-5. I/F connector for extension Evaluation Connector Pin Connector Pin Evaluation MCU Signal name Signal name Number Number...
Specification Through evaluation MCU all hole for a terminal check (U1) The pin assignment of a through evaluation MCU all hole for a terminal check is shown in Table 5-7. Table 5-7. Pin assignment of through evaluation MCU all hole for terminal check (continued) Connector Evaluation Connector...
Page 25
Specification Table 5-8. Pin assignment of through evaluation MCU all hole for terminal check(continue) Connector Evaluation Connector Evaluation Connector Evaluation Signal Signal Signal name name name Number Pin No. Number Pin No. Number Pin No. PE6B PE5B PE4B PE3B PE2B PE1B PE0B Vcc54...
Specification Product selection correspondence evaluation MCU all the terminal for a terminal check The terminal position of a through evaluation MCU all hole for a terminal check is shown in Table 5-19 from Table 5-8 for every setup of the product selection switch on a MCU board. Table 5-9.
Page 27
Specification Table 5-10. Correspondence terminal position of through evaluation MCU all hole for terminal check at time of selection with 100pin LCD (U1) Port Function U1 No. Port Function U1 No. Port Function U1 No. (Cpin) S39/SIN INT00/HC00 S38/SOT INT01/HC01 S37/SCK INT02/HC02 S36/EC1...
Page 28
Specification Table 5-11. Correspondence terminal position of through evaluation MCU all hole for terminal check at time of 80-pin-LCD-less selection (U1) Port Function U1 No. Port Function U1 No. AVcc TO00 TO01 UCK1 PPG2 TRG2 SCL0 SDA0 PPG1 INT17 TRG1 INT16 INT15 INT14...
Page 29
Specification Table 5-12. Correspondence terminal position of through evaluation MCU all hole for terminal check at time of selection with 80pin LCD (U1) Port Function U1 No. Port Function U1 No. AVcc PPG0 TRG0/ADTG UCK0 TO01 TO00 PPG01 PPG00 S16/PPG10 TRG1 S17/PPG11 PPG1...
Page 30
Specification Table 5-13. Correspondence terminal position of through evaluation MCU all hole for terminal check at time of 64-pin-LCD-less selection (U1) Port Function U1 No. Port Function U1 No. AVcc TRG0/ADTG PPG0 INT13 PPG00 INT12 PPG01 INT11 TO00 INT10 TO01 SCL0 SDA0 PPG1...
Page 31
Specification Table 5-14. Correspondence terminal position of through evaluation MCU all hole for terminal check at time of selection with 64pin LCD (U1) Port Function U1 No. Port Function U1 No. AVcc PPG0 TRG0/ADTG UCK0 EC0/SDA0 TO01/SCL0 TO00 PPG01 PPG00 S16/PPG10 S17/PPG11 (Cpin)
Page 32
Specification Table 5-15. Correspondence terminal position of through evaluation MCU all hole for terminal check at time of 48-pin-LCD-less selection (U1) Port Function U1 No. Port Function U1 No. (Cpin) AN07 AN06 RSTX FTEST AN05 INT00/HC00 AN04 INT01/HC01 AN03 INT02/HC02 AN02 INT03/HC03 AN01...
Page 33
Specification Table 5-16. Correspondence terminal position of through evaluation MCU all hole for terminal check at time of selection with 48pin LCD (U1) Port Function U1 No. Port Function U1 No. S09/PPG11 S10/TO10 (Cpin) S11/TO11 S12/EC1 S13/SCK RSTX FTEST S14/SOT S15/SIN PPG0 TRG0/ADTG...
Page 34
Specification Table 5-17. Correspondence terminal position of through evaluation MCU all hole for terminal check at time of 32pin selection (U1) Port Function U1 No. Port Function U1 No. HC12 TO11 AVcc TO10 AVss PPG11 INT00/AN00/PPG00 INT01/AN01/PPG01 INT02/AN02/SCK INT03/AN03/SOT INT04/AN04/SIN INT05/AN05/TO00 (Cpin) INT06/AN06/TO01...
Page 35
Specification Table 5-19. Correspondence terminal position of through evaluation MCU all hole for terminal check at time of 20pin selection (U1) Port Function U1 No. Port Function U1 No. RSTX FTEST INT07/AN07 INT06/AN06/TO01 INT05/AN05/TO00 INT04/AN04/SIN (Cpin) INT03/AN03/SOT PPG0 INT02/AN02/SCK TRG0/ADTG INT01/AN01/PPG01 UCK0/EC0 INT00/AN00/PPG00...
Revision History Document Revision Document Title: MB2146-401 F MC-8FX Family Evaluation Board Operation Guide Document Number: 002-07324 Origin of Revision ECN# Issue Date Description of Change Change 12/07/2004 HUAL Initial release 5274191 05/26/2016 HUAL Migrated Spansion Guide from SS01-26001-1E to Cypress format MB2146-401 F MC-8FX Family Evaluation Board Operation Guide, Doc.