Advertisement
Quick Links
ASSEMBLY AND INSTALLATION
T0435
WARNING:
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. Read and save these instructions.
Important to Know
1. Read all instructions carefully before installation and
operation.
2. If you are not familiar with state and local electrical codes,
it is recommended that you consult with a qualified
electrician.
3. Before installation, shut off power at the main fuse or
circuit breaker box. Be aware that simply turning off the
wall switch is not sufficient to prevent an electrical shock.
4. This fixture requires a 120 VAC, 60 Hz power source.
5. Do not attempt to take the lantern apart; there are no
serviceable parts inside.
6. To avoid sensor damage by lightning or electrical surge,
make sure the grounding wire is securely connected.
Maximum Wattage: 60W Incandescent Bulb
Work Temperature: - 4°F~104°F
HARDWARE CONTENTS Note: Hardware not shown actual size.
AA
Cross Bar
X1
BB
Mounting Screw
X2
INSTRUCTIONS
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
CC
Wire Connector
X3
DD
Headless Screw
X2
Page 1 of 6
Features
1. Energy saving fixture.
2. Use the dim-to-bright illumination option
where you want some minimum illumination
through out the night, such as at your front
entrance or garage door. Use the dark-to-bright
illumination option where you do not need
minimum brightness, such as the backyard
or back porch.
3. When in manual override mode, use wall switch
to keep the light ON till dawn.
EE
Ball Nut
X2
FF
Lock Nut
X4
GG
Rubber Pad
X2
180726
Advertisement
Related Manuals for Vaxcel ProLine T0435
Summary of Contents for Vaxcel ProLine T0435
- Page 1 ASSEMBLY AND INSTALLATION INSTRUCTIONS T0435 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. Read and save these instructions. Features Important to Know 1.
-
Page 2: Safety Information
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. WARNING • Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by removing fuse (or switching off circuit breaker). •... - Page 3 ASSEMBLY INSTRUCTIONS (continued) 1. Thread two headless screws (DD) 4. Attach the fixture to the cross through the cross bar (AA), and then bar (AA) by inserting headless DD A secure them with four lock nuts (FF) screws (DD) into holes on back (two on each side of the cross plate (A), and then secure it with bar (AA).
-
Page 4: Function And Operation
ASSEMBLY INSTRUCTIONS (continued) ASSEMBLY INSTRUCTIONS (continued) ASSEMBLY INSTRUCTIONS (continued) Step 1: Rotate the sensor lens counterclockwise to show “TIME” Knob up the adjustable knobs and slide switch. “LOW LEVEL” Knob (See Fig.1) “SENS” Knob Flathead Screwdriver Step 2: Use the small flathead screwdriver to adjust time, (not included) low level brightness and sensitivity. - Page 5 FUNCTION AND OPERATION (continued) Customization Options Fig. 5 (View from back of sensor head) Shut-off Delay The Shut-off delay is the length of time the light will stay at high- level brightness after motion has ceased to be detected. This Shut-off delay can be set when operation is in “OFF”, or “AUTO”...
-
Page 6: Care And Maintenance
CARE AND MAINTENANCE Clean the glass and coated metal surfaces with a non-abrasive cleaner. Do not use any cleaners with chemicals, solvents or harsh abrasives, The motion detecting lens is coated with a specially painted finish and requires special care when cleaning. Use only a soft dry cloth to dust or wipe the lens area. TROUBLESHOOTING If the light does not work at all: 1.