Page 1
New York, NY 10001 Tele.212-645-9033 FACTORY When contacting Delta Consumer Care please reference the above information. Before contacting Delta Consumer Care please ensure that the information above matches the information found on the label on the Crib End bottom rail,...
Page 2
*Check this product for damaged hardware, loose joints, loose bolts or other fasteners, missing parts, or sharp edges before and after assembly and frequently during use. Securely tighten loose bolts and Do not use crib if any parts are missing, damaged or broken. Contact Delta other fasteners.
Page 3
- Do not scratch or chip the finish. - Inspect the product periodically, contact Delta Children's Products for replacement parts or questions. - Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or a damp, cold basement.
Page 4
P A R TS: MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT. A. Back Rail Top x 1 Part # 21116 D. Right Rear Leg x 1 B. Back Rail Bottom x 1 Part # 21119 C. Left Rear Leg x 1 Part # 21117 Part # 21118 PRODUCT LABEL...
PARTS: HARDWARE AND TOOLS No drills necessary. Do not M. M6 x 80 mm Bolt x 2 use power screwdriver. Flat Head Screwdriver (not supplied) N. M6 x 55 mm Bolt x 14 P. M6 x 45 mm Bolt x 4 R.
Section 1: Crib Assembly Step 1 Parts and tools required to complete step. D. Right Rear H. Right Front Leg x 1 Leg x 1 M4 Allen Wrench Supplied PRODUCT LABEL WARNING LABEL F. Right Crib E. Left Crib End x 1 End x 1 P.
Page 7
Section 1: Crib Assembly Step 2 Parts and tools required to complete step. A. Back Rail Top x 1 M4 Allen Wrench Supplied N. M6 x 55 mm Bolt x 6 B. Back Rail Bottom x 1 From Step 1 Attach (1) Back Rail Bottom (Part B) to the assemblies from step 1 using (4) M6x55mm Bolts (Part N) .
Page 8
Section 1: Crib Assembly Step 3 Parts and tools required to complete step. M4 Allen Wrench Supplied S. M6 x 18 mm Bolt x 4 L. Mattress Support x 1 From Step 2 Attach the Mattress Support (Part L) in all corners using (1) M6 x 18 mm Bolt (Part S) in each corner. Tighten with the M4 Allen Wrench.
Page 9
Section 1: Crib Assembly Step 4 Parts and tools required to complete step. M4 Allen Wrench Supplied J. Front Rail x 1 N. M6 x 55 mm Bolt x 8 From Step 3 Attach (1) Front Rail (Part J) to the assembly from 3 using (8) M6x55mm Bolts (Part N). Tighten with the M4 Allen Wrench.
Section 2: Toddler Bed Conversion Step 1 Parts and tools required to complete step. M4 Allen Wrench Supplied Finished Crib Remove the Front Rail installed in step 4 of section 1 crib assembly.
Page 12
Section 2: Toddler Bed Conversion Step 2 Parts and tools required to complete step. K. Stabilizer Bar x 1 M4 Allen Wrench Supplied T. Φ4x30 mm Metal Pin x 2 U. M6 x 17mm Barrel Nut x 2 From Step 1 Section 2 M.
Page 13
Stabilizer bar must be used when converted to a toddler bed. A toddler bed guardrail is available for this crib. Please see your crib retailer, visit www.DeltaChildren.com or contact delta consumer care for more information. This crib uses Delta Style # 0081 Guardrail.
Section 3: Full Size Bed Conversion Step 1 Parts and tools required to complete step. M4 Allen Wrench Supplied You have the option to convert the crib to a Full Size Bed. Simply follow steps in reverse order to disassemble the crib. Then remove the rear legs from the Left Crib End (Part E) and Right Crib End (Part F) with the M4 Allen Wrench as shown.
Page 15
Section 3: Full Size Bed Conversion Step 2 Parts and tools required to complete step. M4 Allen Wrench S. M6 x 18 mm Bolt x 4 Supplied V. Adapter Plate x 2 Attach Adapter Plates (Part V) to bottom of Rear Side Rail Legs using (4) M6x18mm Bolts (Part S).