Page 1
KEEP INSTRUCTIONS FOR FUTURE USE. ADULT ASSEMBLY REQUIRED Due to the presence of small parts during assembly, keep out of reach of children until assembly is complete. Glider N Ottoman THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE. Consumer Care: Style #: ___________ www.DeltaChildren.com...
Page 2
- DO NOT scratch or chip the finish. - Inspect periodically, contact Delta Children’s Products for replacement parts or questions. - DO NOT store any parts in extreme temperatures and conditions such as a hot attic or a damp, cold basement.
Page 3
PARTS: MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT. C. Right Glider Arm x 1 Part # 23330 B. Left Glider Arm x 1 D. Glider Base x 1 Part # 23329 Part # 23331 A. Glider Back Frame x 1 Part # 23328 H.
Page 4
Section 1: Glider Assembly Step 1 Parts and tools required to complete step. L. Bottom Glides x 4 D. Glider Base x 1 Turn the Glider Seat Base (Part D) over, then attach the Bottom Glides (Part L) as shown. Remove the blacking strip from one glide at a time and adhere the glide to the base, repeat for all 4 glides.
Page 5
Section 1: Glider Assembly Step 2 Parts and tools required to complete step. M. 1/4” x 1-3/8” Bolt x 4 E. Glider Seat x 1 A. Glider Back Frame x 1 M4 Allen Wrench Supplied Attach the Glider Back Frame (Part A) to the Glider Seat (Part E) using (4) 1/4” x 1-3/8” Bolts (Part M), Tighten with the M4 Allen Wrench.
Page 6
Section 1: Glider Assembly Step 3 Parts and tools required to complete step. C. Right Glider Arm x 1 M. 1/4” x 1-3/8” Bolt x 4 M4 Allen Wrench Supplied B. Left Glider Arm x 1 From Step 2 N. 1/4” x 2-1/2” Bolt x 2 P.
Page 7
Section 1: Glider Assembly Step 4 Parts and tools required to complete step. M. 1/4” x 1-3/8” Bolt x 8 D. Glider Base x 1 M4 Allen Wrench Supplied From Step 3 Attach the assembly from step 3 to the Glider Base (Part D) using (8) 1/4” x 1-3/8” Bolts (Part M) as shown in Figure A &...
Page 8
Section 1: Glider Assembly Step 5 Parts and tools required to complete step. From Step 4 F. Left Glider Arm G. Right Glider Arm Cushion x 1 Cushion x 1 Attach (1) Left Glider Arm Cushion (Part F) to the Left Glider Arm with the snaps on the Glider Arm Cushion facing up, slide the Glider Arm Cushion under the Glider Arm and snap all (3) snaps into place.
Page 9
Section 1: Glider Assembly Step 6 Parts and tools required to complete step. From Step 5 H. Glider Seat Cushion x 1 Attach the Glider Seat Cushion (Part H) into the Glider as shown.
Page 10
Section 2: Ottoman Assembly Step 1 Parts and tools required to complete step. M. 1/4” x 1-3/8” Bolt x 4 J. Ottoman Base x 1 K. Ottoman Cushion x 1 M4 Allen Wrench Supplied Attach the Ottoman Cushion (Part K) to the Ottoman Base (Part J) using (4) 1/4” x 1-3/8” Bolts (Part M), Tighten with the M4 Allen Wrench.