Telit Wireless Solutions GS2200M Quick Start Manual
Telit Wireless Solutions GS2200M Quick Start Manual

Telit Wireless Solutions GS2200M Quick Start Manual

Hostless homekit
Hide thumbs Also See for GS2200M:

Advertisement

GS2200M Hostless HomeKit
ADK Quick Start Guide
Supports GS2200 Modules
This Quick Start Guide will walk you through the steps required to
demonstrate HomeKit ADK on GS2200M EVB (Evaluation Board).
The GS2200M_EVB3 has the GainSpan Wi-Fi module and the
Apple Wireless Accessory Configuration (WAC) installed on the
board. Your kit contains:
Quick Start Guide (this document)
GS2200M_EVB3 Evaluation Board with WAC
Serial Cable (USB to Mini-USB)
Preloaded Firmware
Flash Programming Tool
iOS devices with the Home APP from iOS store.
Copyright © 2017 Telit. All rights reserved.
1

Build the Firmware

1
Step
Login at https://wifi.telit.com/secure/login, select SDK
Builder tab and proceed to select the following options for ADK
package as shown below:
If you do not have a login, sign up and register for a Portal account
at:
https://wifi.telit.com/secure/register
2
Step
Click Next to navigate to the build option.
3
Step
Click Build to generate the HomeKit binaries. The build con-
figuration is submitted and a confirmation e-mail is sent notifying that the
HomeKit Custom package is complete and ready to download.
Download and unzip the package, for firmware binaries.
2

Program the GS Module

1
Step
Plug the mini-USB cable, one end of the USB port to
GS2200MIZ board USB0 and the other end of the USB port to the com-
puter or laptop.
2
Step
Turn the PROGRAM/RUN switch to PROGRAM mode on
the EVB and perform a power cycle (switch OFF and switch ON the
power switch)
3
Step
Open GainSpan Serial Flash Programmer GUI applica-
tion from "\Tools\GS_programming_tool\gs2k_flashprogram.exe"..
4
Step
Select the interface and the port with Baud rate 921600.
Click Check Connection.
5
Step
Once the "Connection OK" is displayed, select "Super
Block" and "Current Firmware version" that is located in
"\QuickStart".
6
Step
Click Erase and Program Button.
A green check mark at the lower-right corner of the application win-
dow, indicates successful programming of the module with a dis-
play.
1VV0301455, Rev 1.1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GS2200M and is the answer not in the manual?

Questions and answers

Summary of Contents for Telit Wireless Solutions GS2200M

  • Page 1 This Quick Start Guide will walk you through the steps required to demonstrate HomeKit ADK on GS2200M EVB (Evaluation Board). If you do not have a login, sign up and register for a Portal account https://wifi.telit.com/secure/register...
  • Page 2 1VV0301455, Rev 1.1 Note: For GS2200M EVB, connect Jumper J13 - GPIO Pro- Step Connect to a network. This can be performed in gram Select for Baud Rate 921600 Light Sensor Demo following ways: • Manual Method Using SSID and PWD Commands Step •...
  • Page 3 1VV0301455, Rev 1.1 Step Step Select the accessory to be add to the HomeKit. HOME App pairs and authenticates the HomeKit Accessory. Step Launch “HOME App" from iOS device and tap Add Accessory. Step Upon successful Pairing, tap Done. Step Enter the pass code manually, that is the default authentication code 101-48-505.
  • Page 4 1VV0301455, Rev 1.1 Technical and Product Support Step The light sensor value will be displayed on the HOME App. For any clarification, technical and product support, please The light sensor on the EVB is located along the top left side of email to Telit Technical Support at: the board, labeled as Q10.

Table of Contents