Page 1 Telit EVK2 User Guide 1vv0300704 Rev.17 - 2013/05/30...
Page 2 Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 APPLICABILITY LIST: Model Part Number Engine EVK2 3990150474 Mother Board EVK2-M2MAIR 3990150502 Mother Board + m2mAIR SIM GM862 INTERFACE 3990250670 GM862 GE863-PY INTERFACE 3990250684 GE863-PY GE863-GPS INTERFACE 3990250696 GE863-GPS GE863-SIM INTERFACE 3990250703...
Page 3 Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 HE863-EUR INTERFACE 3990250797 HE863 HE863-EUG INTERFACE 3990250798 HE863 HE863-NAD INTERFACE 3990250799 HE863 HE863-NAR INTERFACE 3990250800 HE863 HE863-NAG INTERFACE 3990250801 HE863 HE863-AUR INTERFACE 3990250803 HE863 HE863-AUG INTERFACE 3990250804 HE863 HE910 INTERFACE 3990250845 HE910...
Page 4 Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE Notice While reasonable efforts have been made to assure the accuracy of this document, Telit assumes no liability resulting from any inaccuracies or omissions in this document, or from use of the information obtained herein.
Page 5 Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 supplied SW, except for the normal non-exclusive, royalty free license to use that arises by operation of law in the sale of a product. Usage and Disclosure Restrictions License Agreements The software described in this document is the property of Telit and its licensors. It is furnished by express license agreement only and may be used only in accordance with the terms of such an agreement.
Page 6: Table Of Contents
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 Contents Introduction ..........................15 1.1. Scope ..............................15 1.2. Audience .............................. 15 1.3. Contact Information, Support ......................15 1.4. Text Conventions ..........................16 1.5. Related Documents ..........................16 1.6. Content of the kit ..........................17 Description ..........................
Page 7 Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 5.4.2. About Current Charger ........................... 29 Serial interface ........................30 6.1. Serial Port Setup ..........................31 Audio Section ........................... 32 7.1. Overview ............................. 32 7.1.1. History ..............................32 7.2. Actual ..............................33 7.2.1.
Page 8 Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 14.1. Stand-alone setup ..........................50 14.2. Interface connectors ........................... 51 14.3. Content of the kit ..........................51 GE863 Interface ........................52 15.1. Stand-alone setup ..........................52 15.2. Content of the kits ..........................53 15.2.1.
Page 9 Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 17.8.2. External host controlling configuration ....................67 17.9. Antenna connectors ..........................69 17.9.1. GSM antenna connector .......................... 69 17.9.2. GPS antenna connector ........................... 69 GE865 – SE867 AGPS Interface ..................70 18.1. Stand-alone setup ..........................70 18.2.
Page 10 Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 20.1. Stand-alone setup ..........................88 20.2. Interface connectors ........................... 88 20.3. Contents of the kit ..........................88 20.1. Power supply ............................89 20.2. GPS external LNA enable signal ....................... 90 20.3. Serial port configuration ........................91 20.4.
Page 11 Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 25.1. Stand-alone setup ..........................106 25.2. Interface connectors ......................... 107 25.3. Content of the kit ..........................107 HE910 family Interface ..................... 108 26.1. Stand-alone setup ..........................109 26.2. Interface connectors ......................... 109 26.3.
Page 12 Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 29.1. Stand-alone setup ..........................125 29.2. Interface connectors ......................... 125 29.3. Antenna connectors .......................... 126 29.3.1. GSM/GPRS Antenna connector ......................126 29.3.2. GNSS antenna connector ........................126 29.4. Expansion Connectors ........................127 29.4.1.
Page 13 Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 32.3.1. CDMA Antenna connector ........................143 32.4. Expansion Connectors ........................143 32.4.1. PL301/PL302 ............................143 32.4.2. PL303/PL304 ............................144 32.4.3. PL102 ..............................144 32.4.4. ON_OFF & UNCONDITIONAL SHUDOWN BUTTONS ..............145 32.5. Content of the kit ..........................145 GL865 V3 Interface ......................
Page 14 CE910 Interface ............................ 173 35.1.14. GL865 V3 Interface ..........................175 SCHEMATICS ........................177 36.1. EVK2 Mother Board ........................178 36.2. GM862 Interface Board ........................183 36.3. GE863 Interface Board ........................184 36.4. GE864 Interface board ........................186 36.5. GE864 Interface board – Automotive ..................... 187 36.6.
Page 15: Introduction
1.1. Scope The Aim of this document is the handling description of the developer’s Evaluation KIT second edition, a laboratory tool named EVK2. 1.2. Audience All given information shall be used as a guide and a starting point for properly developing of your product.
Page 16: Text Conventions
SIM Holder Design Guides, 80000NT10001a • AT Commands Reference Guide, 80000ST10025a • HE910 AT Commands Reference Guide, 80378ST10091A • Telit EVK2 User Guide, 1vv0300704 Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 16 of 243...
Page 17: Content Of The Kit
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 1.6. Content of the kit Please check out the content of your EVK2 kit; if any of the items is missing, please contact your supplier. Description Quantity EVK2 MOTHERBOARD INFORMATION NOTE 2 PIN JUMPER FEMALE CONN ASSEMBLED USB A-B CABLE RED &...
Page 18: Description
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 Description The motherboard CS1139B can be split into several functional blocks depending on the implemented function; the following drawings show a block diagram and the displacement of the main blocks on motherboard.
Page 19: Pcb Characteristics
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 Figure 3: CS1139B circuital displacement 2.1. PCB characteristics Material: Thickness: 0, 95 mm Surface finishing: Chemical gold plate Ni 5um/ Au 0,1um Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved...
Page 20: Mechanical Characteristics Of The Assembled Pcbs
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 2.2. Mechanical characteristics of the assembled PCBs 2.2.1. Mother Board CS1139B Length 100 mm (max 102,6 mm) Width 160 mm (max 166,10mm) Height 47,6 mm (included the support with columns) Weight 200 gr (without any interface) 2.2.2.
Page 21: Gc864 Interface Cs1203B
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 2.2.6. GC864 Interface CS1203B Length 66,04 mm Width 78,74 mm Height 21,00 mm Weight gr (without the module) 2.2.7. GC864-C2 Interface CS1231X Length 50,00 mm Width 33,00 mm Height 5,60 mm Weight 13,8 gr (with module) 2.2.8.
Page 22: He910 Interface Cs1467C
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 Width 67,50 mm Height 20,80 mm Weight 55 gr (without module) 2.2.13. HE910 Interface CS1467C Length 107,00 mm Width 102,00 mm Height 25,00 mm 2.2.14. UE910 Interface CS1467D Length 107,00 mm Width...
Page 23: Gl865 V3 Interface Cs1531B
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 2.2.20. GL865 V3 Interface CS1531B Length 92,00 mm Width 89,00 mm Height 25,00 mm 2.2.21. LE920 Interface KS0145B Length 92,00 mm Width 107,00 mm Height 25,00 mm NOTE: The overall height for every combination (mother board + interface board) is still the height of the mother board Reproduction forbidden without Telit Communications S.p.A.
Page 24: Startup Procedure
NOTE: When you use USB port, it is very important to respect the following sequences: Start: first turning ON the EVK2 and then connecting it to the PC Stop: first disconnecting the PC and then turning OFF the EVK2 Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved...
Page 25: Insertion Of The Interface Boards
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 Insertion of the Interface Boards Every Interface Board must be inserted on CS1139B paying great attention to match the position of the main connectors; this has been made easy: optically by a triangle drawn on both printed circuits (except CS1231X) ;...
Page 26: Power Supply Setting
1vv0300704 Rev.17 – 2013/05/30 Power supply setting The EVK2 could be powered by different external sources, only one at time. The requested setting is made inserting the proper jumper connectors in the right position as described in the following paragraphs.
Page 27: Variable Dc Source
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 5.2. Variable DC source Connect a + 5÷40 V / ≥ 1A variable DC source to PL102 (by wires) or to SO101 (by coaxial plug), with care to the polarities. Short pin1& pin2-PL104 and pin1& pin2-PL105 by inserting 2 contacts jumper connectors.
Page 28: Coaxial Plug
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 5.2.1. Coaxial Plug The figure 7 shows the connections of the Power Plug of left part of figure 6. Figure 7: Coaxial “Power Plug” connection. 5.3. Li-Ion Battery pack and Charger Connect a Li-Ion battery pack to PL107 with care to the polarity then short pin 2& pin3- PL105 by inserting the 2 contacts jumper connector.
Page 29: Application Notes
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 5.4. Application Notes 5.4.1. Li-Ion Battery Pack The 3.7V Li-Ion rechargeable Battery Pack should be connected directly to PL107 connector. Remember to use the connection cables as short as possible, with the appropriate conductors gauge and the other attributes, such as device power budget and cable flexibility, in order to match the specified voltage drop (especially during the high current absorption periods).
Page 30: Serial Interface
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 Serial interface The following figure shows the architecture of the serial ports. Figure 9: Serial ports block diagram. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 30 of 243...
Page 31: Serial Port Setup
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 6.1. Serial Port Setup Communications between your application and the Telit modules are allowed connecting the DTE to the Asynchronous Serial Interfaces of Base-Band Chip, ASC0 and ASC1, through the stacked standard RS232 communications port (double 9 way D-socket connector at slow data rates of RS232 protocol) or a standard USB-B Series receptacle (at higher data rates of USB1.1 specification through a CMOS HUB that realizes a multiple attachment point...
Page 32: Audio Section
The Base Band chip of the Telit’s modules provides one or two (depends of model) audio paths both in receive and in transmit sections, which could be active only one at time. To turn on your well-suited section on EVK2, please refer to “AF Amplifiers Setting “paragraph and followings.
Page 33: Actual
Actual The HS and HF definitions have been kept in the Software and on the schematics of the Telit modules, but with EVK2 we will refer to Audio1 and Audio2 section instead of Handset and Handsfree respectively, remembering that: they can have fully equivalent electrical performances (like the two microphone amplifiers)
Page 34: Benefits And Disadvantages
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 7.3.2. Benefits and disadvantages Differential amplifiers are desirable to use, especially in audio applications where signal levels are very low such as those from microphones. Classically, the benefits obtained from differential amplification are: Increase of Common Mode Rejection Ratio (CMRR) Differential inputs enable cancellation of any noise common on both inputs.
Page 35: Settings
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 7.3.3. Settings Connecting your accessories to SO401 in/out connector, you will implement Single Ended Input/Output configurations. Removing all 2 contacts jumpers inserted between PL402&PL403 or PL403&PL404, the in/out lines of our modules will be directly available on PL402 and PL404 connectors.
Page 36: Af Amplifiers Setting
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 AF Amplifiers Setting The Base Band Processor Audio Amplifiers selection is made short-circuiting PL403&PL402 (RX Amplifier 1) or PL403&PL404 (RX Amplifier 2). In such a way you could verify the complete performance of both audio paths.
Page 37: Audio Outputs
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 Audio outputs The EVK2 output audio signals could be drive a device connected to SO401 ( LOW AF POWER ) or to PL401 ( mode HIGH AF POWER mode 9.1. Low AF Power Mode...
Page 38: High Af Power Mode
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 9.2. High AF Power Mode Connecting an 8 ohm Speaker to PL401 by a 2 contacts female connector, you could drive it through the 500mW Power Amplifier. In this case the Speaker will be driven in fully differential configuration, with no side connected to ground and without any output coupling capacitor.
Page 39: Speaker And Stand-Alone Microphone
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 9.2.1. Speaker and Stand-alone Microphone If you are using a Speaker, you can connect a stand-alone electrete microphone by a coaxial 2,5mm plug to SO401, respecting the following pin-out. Figure 17: Microphone Plug Connection Figure 18: Speaker &...
Page 40: Speaker Plus Headset
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 9.2.2. Speaker plus Headset If you have chosen to connect the Speaker to HIGH AF POWER output, without having a stand-alone electret microphone, it is also possible to connect a standard off-the-shelf Headset to SO401 without any problem, as shown in the figure 18: the AF output signal will be heard on both Speaker and Earpiece.
Page 41: Audio Accessories
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 Audio Accessories The following tables show the suggested specification to obtain the best performance from off- the-shelf accessories. 10.1. Headset Nominal sensitivity -45dBV /1Pa (+/- 3dB) Line coupling Nominal Voltage Range of Using Voltage (1÷10)V...
Page 42: Stand-Alone Microphone
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 10.2. Stand-alone microphone Nominal sensitivity -45dBV /1Pa (+/- 3dB) Line coupling Nominal Voltage Range of Using Voltage (1÷10)V Consumption Current (150÷500 ) μA Impedance 2,2KΩ Signal to Noise Ratio 56dB /1KHz/1Pa /A curve...
Page 43: Indication And Services
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 Indication and services 11.1. Optical Indicators 11.1.1. Status Led It is a debug aid that shows information on the network service availability and Call status. LED status Device Status Permanently off Device off...
Page 44: Charge Led
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 11.1.2. CHARGE Led A yellow LED is used as Charge In Act Indicator, as explained in the following table. CHARGE LED Meaning Always on Start Charge/ Hugh current Charge in act Always off...
Page 45: Switches
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 11.2. Switches You turn On/Off or Reset the EVK2 by 2 push buttons. 11.2.1. POWER ON Switch Push ON/OFF button on EVK Board for at least 5 seconds, on the XX910 form factor...
Page 46: Connectors Pinout
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 Connectors pinout 12.1. Motherboard to Module The connections between CS1139B and every Telit module Interface Board are made through two 40 pin male connectors. Theirs pin functions are listed in the following tables.
Page 47 Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 EAR_MT+ AC Out Voltage Audio DC voltage INT/EXT Switching MIC_HF- AC In Voltage Audio MIC_MT+ AC In Voltage Audio MIC_HF+ AC In Voltage Audio MIC_MT- AC In Voltage Audio DC voltage Power...
Page 48 Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 SIMVCC DC voltage SIM Power SIMIN DC voltage SIM inside detector DC voltage Power DC voltage Power DC voltage Power Table 9: PL202-CS1139B Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved...
Page 49: Module Interface Boards
13.1. Generality You can use your EVK2 with see APPLICABILITY LIST Telit modules fitted on its own Interface Board; all connections are made through 2x40 contacts connectors. It’s possible to use these Interface Boards also in stand-alone mode, inserting the “not mounted”...
Page 50: Gm862 Interface
No settings are needed. Figure 23: GM862 Interface Board 14.1. Stand-alone setup If you need to use the interface out of EVK2 (Stand-alone setup) you have to mount the following missing components: RESET Button ON Button; STATUS LED and its load resistance.
Page 51: Interface Connectors
Telit extension boards, measurements equipment or other tools 2 female connectors (40 pins each one: SO101, SO102), to connect the interface to the EVK2 mother board circuits (power supply lines, serial in/out lines, audio in/out lines). 14.3. Content of the kit Please check out the contents of your interface kit;...
Page 52: Ge863 Interface
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 GE863 Interface This board allows easily interfacing the GE863 modules with the EVK2 and testing their functionalities; Figure 24: GE863 Interface Boards: GE863-QUAD or GE863-SIM (at left) and GE863-GPS (at right) 15.1.
Page 53: Content Of The Kits
2 male connectors (4 pins each one: PL101, PL102) to select the Serial port configuration 2 female connectors (40 pins each one: SO101, SO106) to connect the interface to the EVK2 mother board circuits (power supply lines, serial in/out lines, audio in/out lines) 2 male connectors (30 pins each one: PL103, PL104), on which it is possible to connect external devices like user’s application, Telit extension boards, measurements equipment or...
Page 54: Usb Connector
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 GPS RF connector (SMA Female) USB B-type connector and its circuitry (see schematic 30276SE11151A) Figure 25: Connectors displacement on GE863-GPS 15.5. USB connector The USB interface provides 2 serial ports that are related to the NMEA serial port and SIRF- Binary serial port of GE863-GPS module.
Page 55: Serial Port Configuration
GE863-PY/QUAD The 2 contacts jumpers have to be fitted between pin1&pin2 of PL101-PL102 connectors. This carries out the Python Debug Port on Trace Port of EVK2. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 55 of 243...
Page 56: Ge863 - Gps
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 Figure 27: Jumpers setting for GE863-PY/QUAD 15.6.2. GE863 – GPS The 2 contacts jumpers have to be fitted between pin2&pin3 or pin3&pin4 of PL101-PL102 connectors. “CONTROLLED MODE” This set the SIRF Binary to serial port of the modem. (Typical application Design)
Page 57: Antenna Connectors
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 “SEPARATED SERIAL PORT” This set the SIRF Binary available on the USB connector. Figure 29: Jumpers setting for SIRF BINARY port available on USB connector NOTE: In this configuration soma AT GPS commands are not available. Refer to AT Commands Reference User Guide.
Page 58: Ge864 Interface
This board allows easily interfacing the GE864 modules with the EVK2 and testing their functionalities. No settings are needed. Figure 30: GE864 Interface Board 16.1. Stand-alone setup If you need to use the interface out of EVK2 (Stand-alone setup) you have to mount the following missing components: • the SIMCARD Holder; •...
Page 59: Interface Connectors
Telit extension boards, measurements equipment or other tools; 2 female connectors (40 PTH pins each one: SO101, SO102), to connect the interface to the EVK2 mother board circuits (power supply lines, serial in/out lines, audio in/out lines); 16.3. Content of the kit Please check out the contents of your interface kit;...
Page 60: Ge864-Gps Interface
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 GE864-GPS Interface This board allows testing the functionalities and performance of the GE864-GPS module. Figure 31: GE864-GPS Interface Board 17.1. Part numbering This board comes in three different configurations, each characterized by its own part number, depending on the module it contains.
Page 61: Stand-Alone Setup
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 17.2. Stand-alone setup The interface can be used without the EVK2, in this case the following components have to be soldered on the board: the GSM-RESET button the GSM-ON button the STATUS led and its load resistor.
Page 62: Power Supply
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 17.5. Power supply The module (but not the whole interface) receives its power supply from PL105: this jumper must always be plugged in, except when a series measurement instrument is needed. Figure 32: Jumper for VBATT.
Page 63: Serial Port Configuration
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 Figure 33: Jumper on PL104. 17.7. Serial port configuration By means of proper jumper connections on PL201, three different configurations for serial outputs can be selected. These configurations are mutually exclusive. Figure 34: GE864-GPS Interface Board serial connections Reproduction forbidden without Telit Communications S.p.A.
Page 64: Asc1 To Rs-232
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 17.7.1. ASC1 to RS-232 This configuration connects the ASC1 UART to the Trace serial connector of the EVK2. Figure 35: ASC1 to RS-232 (Trace) configuration 17.7.2. GPS to ASC1 (internal host controlling configuration) This configuration directly connects the host GSM module to the GPS receiver, thus setting the GPS receiver in Controlled Mode.
Page 65: Gps To Rs-232 (External Host Controlling Configuration)
Figure 37, i.e. connecting the NMEA line with the RS-232, and at the same time setting the EVK2 serial line on USB Mode, as shown in Paragraph 7.1 of this document. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved...
Page 66: Gpio Settings
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 17.8. GPIO settings The interface allows choosing among different options for driving the GPS control signals: Using the GPIOs of the GSM module Using an external host Manually controlling the signals by plugging a jumper.
Page 67: External Host Controlling Configuration
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 Figure 39: Settings for PL101 and PL102: internal host, cs1439b and cs1439b-B Note that jumper settings are detailed in the pictures above. The signal connected to pin10 of PL102 is no longer available, and it is recommended to tie it to ground by plugging a jumper between pin10 &...
Page 68 Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 Figure 40: Settings for PL101 and PL102: external host, cs1439b-A. Figure 41: Settings for PL101 and PL102: external host, cs1439b and cs1439b-B. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved...
Page 69: Antenna Connectors
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 17.9. Antenna connectors 17.9.1. GSM antenna connector A GSM antenna must be connected to SO105. 17.9.2. GPS antenna connector A GPS antenna must be connected to SO103. WARNING: Don’t connect a antenna on this connector Reproduction forbidden without Telit Communications S.p.A.
Page 70: Ge865 - Se867 Agps Interface
Telit guidelines. Figure 42: GE865/SE867-AGPS Interface Board 18.1. Stand-alone setup The interface can be used without the EVK2, in this case the following components have to be soldered on the board: the RESET button the ON button the STATUS led and its load resistor.
Page 71: Interface Connectors
2 female connectors (40 PTH pins each one: SO101 and SO104), to connect the interface to the EVK2 mother board circuits (power supply lines, serial in/out lines, audio in/out lines) 1 male connector (5 PTH pins: PL104), which makes available in one place all GPIOs...
Page 72: Gsm To Gps (Gsm Controlling Configuration)
This configuration is achieved by plugging a female jumper connector on pin1 & pin2 of both PL201 and PL206. It allows to connect the GE865 UART with SE867-AGPS UART, thereby putting the board in the so-called controlled mode. No connection with the EVK2 RS-232 Trace is present.
Page 73: Gsm To Trace
GSM to Trace This configuration is realized by plugging a female jumper connector on pin2 & pin3 of both PL201 and PL206. It allows redirecting the GE865 UART to the EVK2 RS-232 Trace. No connection with the SE867 UART is present.
Page 74: Gps To Trace(External Host Controlling Configuration)
GPS to Trace(external host controlling configuration) This configuration is achieved by plugging two female jumper connectors on PL202 and PL207. It allows redirecting the SE867 UART to the EVK2 RS-232 Trace. No connection with the GE865 UART is present. Figure 45: Jumpers in GPS to Trace configuration.
Page 75: Ge865 - Jf2 Interface
Telit guidelines. Figure 46: GE865/JF2 Interface Board. 19.1. Stand-alone setup The interface can be used without EVK2 and in this case the following components have to be soldered to the board: - RESET button - GSM ON/OFF button - GSM STATUS led and its load resistor Reproduction forbidden without Telit Communications S.p.A.
Page 76: Interface Connectors
GPS module - 2 female connectors (40 PTH pins each one: SO301 and SO302), to connect the interface to the EVK2 mother board circuits (power supply lines, serial in/out lines, audio in/out lines) - 1 GSM RF connector (SMA Female: SO105)
Page 77: Gps External Lna Enable Signal
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 Figure 46: Jumper for VBATT. 19.5. GPS external LNA enable signal The module contains an internal LNA for the GPS antenna. The user can though decide to use an external LNA: this option is selected by means of a software command, which puts the internal LNA in a low gain mode and provides an additional signal to enable the external LNA.
Page 78 Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 EXTERNAL LNA CONTROLLED BY ENABLE SIGNAL EXTERNAL LNA ALWAYS ON Figure 47: Jumper selection on PL202. In order to use the External LNA controlled by the GE865 signal the user musts insert a jumper in pins 14-16 of PL301.
Page 79: Serial Port Configuration
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 19.6. Serial port configuration By means of proper jumper connections on PL303, it is possible to choose different configurations for serial or USB outputs. These configurations are mutually exclusive. GE865 JF2- PL303...
Page 80: Gsm To Trace
Figure 49: GSM to RS-232 (Trace) configuration 19.8. GPS to Trace This configuration allows sending the GPS output to the Trace serial connector of EVK2 by means of transceivers. Figure 50.GPS to RS232 (Trace) Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved...
Page 81: Gsm To Usb
19.10. GPS to USB The NMEA sentences can be redirected to the EVK2’s USB port by setting the PL303 as explained in the Figure 53, i.e. connecting the NMEA line with the RS-232, and at the same time setting the EVK2 serial line on USB mode, as showed in Paragraph 7.1 of this document.
Page 82: Gps To Gsm (Internal Host Controlling Configuration)
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 19.11. GPS to GSM (internal host controlling configuration) This configuration directly connects the host GSM module to the GPS receiver, thus setting the GPS receiver in Controlled Mode. Figure 53: GPS to GSM configuration 19.12.
Page 83: Internal Host Controlling Configuration
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 19.12.1. Internal host controlling configuration The following settings on PL301 and PL302 allow selecting the internal host configuration. Figure 54: Settings for PL301 and PL302: internal host controlling Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved...
Page 84: External Host Controlling Configuration
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 19.12.2. External host controlling configuration The following settings on PL301 and PL302 allow selecting the external host configuration. Figure 55: Settings for PL301 and PL302: external host. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved...
Page 85: Gps Serial Interface Setting
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 19.13. GPS serial interface setting GPS module has the capability to operate in serial UART mode, SPI mode or I2C mode depending upon how the JF2 GPIO6 and GPIO7 pins are strapped at power up. In the...
Page 86: Antenna Connectors
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 19.16. Antenna connectors 19.16.1. GSM antenna connector A GSM antenna must be connected to SO105. 19.16.2. GPS antenna connector A GPS antenna must be connected to SO201. WARNING: Don’t connect a antenna on the GPS antenna connector Reproduction forbidden without Telit Communications S.p.A.
Page 87: Gl865 - Sl869/Jn3 Interface
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 GL865 – SL869/JN3 Interface This board allows testing the functionalities and performance of the GL865-V3 and SL869/JN3 modules interconnected according to Telit guidelines. Figure 56: GL865 – SL869/JN3 Interface Board. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved...
Page 88: Stand-Alone Setup
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 20.1. Stand-alone setup The interface can be used without EVK2 and in this case the following components have to be soldered to the board: -GSM RESET button - GSM ON/OFF button - GPS STATUS led and its load resistor - GSM STATUS led and its load resistor (both NO MOUNT) 20.2.
Page 89: Power Supply
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 20.1. Power supply The GL865 module (but not the whole interface) receives its power supply from PL101: this jumper must always be plugged on except when a series measurement instrument is needed.
Page 90: Gps External Lna Enable Signal
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 20.2. GPS external LNA enable signal The module contains an internal LNA for the GPS antenna. The user can though decide to use an external LNA: this option is selected by means of a software command, which puts the internal LNA in a low gain mode and provides an additional signal to enable the external LNA.
Page 91: Serial Port Configuration
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 20.3. Serial port configuration By means of proper jumper connections on PL302, it is possible to choose different configurations for serial or USB outputs. These configurations are mutually exclusive. SL869/JN3 GL865-SL869/JN3 INTERFACE EVK2 Figure 59: GL865 - SL869/JN3 Interface Board serial connections Reproduction forbidden without Telit Communications S.p.A.
Page 92 Figure 60: GSM to RS-232 (Trace) configuration 20.5. GPS to Trace This configuration allows sending the GPS output to the Trace serial connector of EVK2 by means of transceivers Figure 61: GPS to RS-232 (Trace) configuration Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved...
Page 93: Gsm To Usb
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 20.6. GSM to USB This configuration connects the GSM to the USB connector of the EVK2. Figure 62: GSM to USB configuration 20.7. GPS to USB This configuration connects the GPS to the USB connector of the EVK2.
Page 94: Gps To Gsm (Internal Host Controlling Configuration)
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 20.8. GPS to GSM (internal host controlling configuration) This configuration directly connects the host GSM module to the GPS receiver, thus setting the GPS receiver in Controlled Mode. Figure 64: GPS to GSM configuration Reproduction forbidden without Telit Communications S.p.A.
Page 95: Gpio Settings
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 20.9. GPIO settings The interface allows choosing among different options for driving the GPS control signals: - Using the GPIOs of the GSM module - Using an external host - Manually controlling the signals by plugging jumpers.
Page 96: External Host Controlling Configuration
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 20.9.2. External host controlling configuration The following settings on PL300 and PL301 allow selecting the external host configuration. VTRASL GPS_BOOT GPS_EN GPS_PPS Figure 66: Settings for PL300 and PL301: external host. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved...
Page 97: Antenna Connectors
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 20.10. Antenna connectors 20.10.1. GSM antenna connector A GSM antenna must be connected to SO101. 20.10.2. GPS antenna connector A GPS antenna must be connected to SO201 Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved...
Page 98: Gc864 Interface
No settings are needed. Figure 67: GC864 Interface Board 21.1. Stand-alone setup If you need to use the interface out of EVK2 (Stand-alone setup) you have to mount also: the SIMCARD Holder; the RESET Button the ON Button; the STATUS LED and its load resistance.
Page 99: Interface Connectors
Telit extension boards, measurements equipment or other tools 2 female connectors (40 PTH pins each one: SO101, SO102), to connect the interface to the EVK2 mother board circuits (power supply lines, serial in/out lines, audio in/out lines). 21.3. Content of the kit Please check out the contents of your interface kit;...
Page 100: Gc864-C2 Family Interface
No settings are needed. Figure 68: GC864-C2 Interface Board 22.1. Stand-alone setup If you need to use the interface out of EVK2 (Stand-alone setup) you have to mount the following missing components: the SIMCARD Holder ; the ON Button ;...
Page 101: Interface Connectors
Telit extension boards, measurements equipment or other tools; 2 female connectors (40 PTH pins each one: SO101, SO104), to connect the interface to the EVK2 mother board circuits (power supply lines, serial in/out lines, audio in/out lines); 22.3. Content of the kit Please check out the contents of your interface kit;...
Page 102: Ge865 Interface
No settings are needed. Figure 69: GE864 Interface Board 23.1. Stand-alone setup If you need to use the interface out of EVK2 (Stand-alone setup) you have to mount the following missing components: the RESET Button the ON Button; the STATUS LED and its load resistance.
Page 103: Interface Connectors
Telit extension boards, measurements equipment or other tools; 2 female connectors (40 PTH pins each one: SO101, SO102), to connect the interface to the EVK2 mother board circuits (power supply lines, serial in/out lines, audio in/out lines); 23.3. Content of the kit Please check out the contents of your interface kit;...
Page 104: Gl865 Interface
No settings are needed. Figure 70: GL865 Interface Board 24.1. Stand-alone setup If you need to use the interface out of EVK2 (Stand-alone setup) you have to mount the following missing components: the RESET Button the ON Button; the STATUS LED and its load resistance.
Page 105: Interface Connectors
Telit extension boards, measurements equipment or other tools; 2 female connectors (40 PTH pins each one: SO101, SO102), to connect the interface to the EVK2 mother board circuits (power supply lines, serial in/out lines, audio in/out lines); 24.3. Content of the kit Please check out the contents of your interface kit;...
Page 106: Uc864 Family Interface
For more information please refer to 1vv0300771 (UC864/CC864 Interface Board User Guide) Figure 71: UC864 Interface Board 25.1. Stand-alone setup If you need to use the interface out of EVK2 (Stand-alone setup) you have to mount the following missing components: the RESET Button the ON Button;...
Page 107: Interface Connectors
(40 PTH pins each one: CON102, CON103), to connect the interface to the EVK2 mother board circuits (power supply lines, serial in/out lines, audio in/out lines); 2 USB connectors (selectable by Jumper Setting) For additional details on the connections and the possible Jumper settings please refer to the Interface board User guide (1vv0300771) 25.3.
Page 108: He910 Family Interface
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 HE910 family Interface This board allows easily interfacing the HE910 modules with the EVK2 and testing their functionalities; No settings are needed. Figure 72: HE910 Interface Board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved...
Page 109: Stand-Alone Setup
2 female connectors (40 PTH pins each one: SO101, SO104), to connect the interface to the EVK2 mother board circuits (power supply lines, serial in/out lines, audio in/out lines); 1 USB connector (SO202) related to the HE910 USB 2.0 port.
Page 110: Antenna Connectors
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 26.3. Antenna connectors 26.3.1. GSM/UMTS Antenna connector A GSM/UMTS compatible antenna (Refer to the product’s HW user guide) antenna must be connected to SO103. 26.3.2. Receiver Diversity Antenna connector A GSM/UMTS compatible antenna (Refer to the product’s HW user guide) antenna could be connected to SO105.
Page 111: Expansion Connectors
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 26.4. Expansion Connectors 26.4.1. PL301/PL302 The connectors are carrying the following signals: PL301 Pin# Pin Name Description STAT_LED Status Led RESERVED C125/RING C107/DSR C109/DCD RESERVED PL302 Pin# Pin Name Description GPIO_01 Default function is Status Led...
Page 112: Pl303/Pl304/Pl305
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 26.4.2. PL303/PL304/PL305 The connectors are carrying the following signals: PL303 Pin# Pin Name Description TX_AUX Auxiliary serial port (TX) RX_AUX Auxiliary serial port (RX) SPI_CLK SPI_MRDY SPI_SRDY GPIO_08 GPIO_09 GPIO_10 RESERVED PL304...
Page 113: Pl102
The 2 Buttons present on the Interface should be used to control the Power ON and UNCONDITIONAL SHUTDOWN lines of the module. The 2 Buttons on the EVK2 could not be used with the HE910 Interface. 26.5. Content of the kit Please check out the contents of your interface kit;...
Page 114: Ue910 Family Interface
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 UE910 family Interface This board allows easily interfacing the UE910 modules with the EVK2 and testing their functionalities; No settings are needed. Figure 76: UE910 Interface Board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved...
Page 115: Stand-Alone Setup
2 female connectors (40 PTH pins each one: SO101, SO104), to connect the interface to the EVK2 mother board circuits (power supply lines, serial in/out lines, audio in/out lines); 1 USB connector (SO202) related to the UE910 USB 2.0 port.
Page 116: Antenna Connectors
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 27.3. Antenna connectors 27.3.1. GSM/UMTS Antenna connector A GSM/UMTS compatible antenna (Refer to the product’s HW user guide) antenna must be connected to SO103. 27.4. Expansion Connectors 27.4.1. PL301/PL302 The connectors are carrying the following signals:...
Page 117: Pl303/Pl304/Pl305
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 27.4.2. PL303/PL304/PL305 The connectors are carrying the following signals: PL303 Pin# Pin Name Description TX_AUX Auxiliary serial port (TX) RX_AUX Auxiliary serial port (RX) SPI_CLK SPI_MRDY SPI_SRDY GPIO_08 GPIO_09 GPIO_10 RESERVED PL304...
Page 118: Pl102
The 2 Buttons present on the Interface should be used to control the Power ON and UNCONDITIONAL SHUTDOWN lines of the module. The 2 Buttons on the EVK2 could not be used with the UE910 Interface. 27.5. Content of the kit Please check out the contents of your interface kit;...
Page 119: Ge910 Interface
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 GE910 Interface This board allows easily interfacing the GE910 module with the EVK2 and testing their functionalities; No settings are needed. Figure 78: GE910 Interface Board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved...
Page 120: Stand-Alone Setup
2 female connectors (40 PTH pins each one: SO101, SO104), to connect the interface to the EVK2 mother board circuits (power supply lines, serial in/out lines, audio in/out lines); 1 USB connector (SO202) related to the GE910 USB 2.0 port.
Page 121: Antenna Connectors
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 28.3. Antenna connectors 28.3.1. GSM/GPRS Antenna connector A GSM/GPRS compatible antenna (Refer to the product’s HW user guide) antenna must be connected to SO103. 28.4. Expansion Connectors 28.4.1. PL301/PL302 The connectors are carrying the following signals:...
Page 122: Pl303/Pl304
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 28.4.2. PL303/PL304 The connectors are carrying the following signals: PL303 Pin# Pin Name Description TX_AUX Auxiliary serial port (TX) RX_AUX Auxiliary serial port (RX) RESERVED RESERVED RESERVED GPIO_08 GPIO_09 GPIO_10 RESERVED PL304...
Page 123: On_Off & Unconditional Shutdown Buttons
The 2 Buttons present on the Interface should be used to control the Power ON and UNCONDITIONAL SHUTDOWN lines of the module. The 2 Buttons on the EVK2 could not be used with the GE910 Interface. 28.5. Content of the kit Please check out the contents of your interface kit;...
Page 124: Ge910-Gnss Interface
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 GE910-GNSS Interface This board allows easily interfacing the GE910-GNSS module with the EVK2 and testing their functionalities; No settings are needed. Figure 80: GE910-GNSS Interface Board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved...
Page 125: Stand-Alone Setup
2 female connectors (40 PTH pins each one: SO101, SO104), to connect the interface to the EVK2 mother board circuits (power supply lines, serial in/out lines, audio in/out lines); 1 USB connector (SO202) related to the GE910-GNSS USB 2.0 port.
Page 126: Antenna Connectors
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 29.3. Antenna connectors 29.3.1. GSM/GPRS Antenna connector A GSM/GPRS compatible antenna (Refer to the product’s HW user guide) antenna must be connected to SO103. 29.3.2. GNSS antenna connector A GNSS antenna could be connected to SO102. Please refer to the product’s HW user guide for the proper type.
Page 127: Expansion Connectors
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 29.4. Expansion Connectors 29.4.1. PL301/PL302 The connectors are carrying the following signals: PL301 Pin# Pin Name Description STAT_LED Status Led RESERVED C125/RING C107/DSR C109/DCD RESERVED PL302 Pin# Pin Name Description Jumper to EVK2...
Page 128: Pl303/Pl304
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 29.4.2. PL303/PL304 The connectors are carrying the following signals: PL303 Pin# Pin Name Description TX_AUX Auxiliary serial port (TX) RX_AUX Auxiliary serial port (RX) RESERVED RESERVED RESERVED GPIO_08 GPIO_09 GPIO_10 RESERVED PL304...
Page 129: On_Off & Unconditional Shutdown Buttons
The 2 Buttons present on the Interface should be used to control the Power ON and UNCONDITIONAL SHUTDOWN lines of the module. The 2 Buttons on the EVK2 could not be used with the GE910-GNSS Interface. For the GNSS capabilities refer to GE910-GNSS Hardware User Guide.
Page 130: Ge910-Quad V3 Interface
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 GE910-QUAD V3 Interface This board allows easily interfacing the GE910-QUAD V3 module with the EVK2 and testing their functionalities. No settings are needed. Figure 84: GE910 Interface Board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved...
Page 131: Stand-Alone Setup
2 female connectors (40 PTH pins each one: SO101, SO104), to connect the interface to the EVK2 mother board circuits (power supply lines, serial in/out lines, audio in/out lines); 1 USB connector (SO202) related to the GE910 USB 2.0 port.
Page 132: Antenna Connectors
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 30.3. Antenna connectors 30.3.1. GSM/GPRS Antenna connector A GSM/GPRS compatible antenna (Refer to the product’s HW user guide) antenna must be connected to SO103. 30.4. Expansion Connectors 30.4.1. PL301/PL302 The connectors are carrying the following signals:...
Page 133: Pl303/Pl304
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 30.4.2. PL303/PL304 The connectors are carrying the following signals: PL303 Pin# Pin Name Description TX_AUX Auxiliary serial port (TX) RX_AUX Auxiliary serial port (RX) RESERVED RESERVED RESERVED GPIO_08 GPIO_09 GPIO_10 RESERVED PL304...
Page 134: On_Off & Unconditional Shutdown Buttons
The 2 Buttons present on the Interface should be used to control the Power ON and UNCONDITIONAL SHUTDOWN lines of the module. The 2 Buttons on the EVK2 could not be used with the GE910 Interface. 30.5. Content of the kit Please check out the contents of your interface kit;...
Page 135: De910 Family Interface
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 DE910 family Interface This board allows easily interfacing the DE910 modules with the EVK2 and testing their functionalities; No settings are needed. Figure 86: DE910 Interface Board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved...
Page 136: Stand-Alone Setup
2 female connectors (40 PTH pins each one: SO101, SO104), to connect the interface to the EVK2 mother board circuits (power supply lines, serial in/out lines, audio in/out lines); 1 USB connector (SO202) related to the DE910 USB 2.0 port.
Page 137: Antenna Connectors
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 31.3. Antenna connectors 31.3.1. CDMA Antenna connector A CDMA compatible antenna (Refer to the product’s HW user guide) must be connected to SO103. 31.3.2. Receiver Diversity Antenna connector A CDMA compatible antenna (Refer to the product’s HW user guide) could be connected to SO105.
Page 138: Expansion Connectors
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 31.4. Expansion Connectors 31.4.1. PL301/PL302 The connectors are carrying the following signals: PL301 Pin# Pin Name Description STAT_LED Status Led RESERVED C125/RING C107/DSR C109/DCD RESERVED PL302 Pin# Pin Name Description GPIO_01 Default function is Status Led...
Page 139: Pl303/Pl304/Pl305
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 31.4.2. PL303/PL304/PL305 The connectors are carrying the following signals: PL303 Pin# Pin Name Description TX_AUX Auxiliary serial port (TX) RX_AUX Auxiliary serial port (RX) RESERVED RESERVED RESERVED GPIO_08 GPIO_09 GPIO_10 RESERVED PL304...
Page 140: Pl102
The 2 Buttons present on the Interface should be used to control the Power ON and UNCONDITIONAL SHUTDOWN lines of the module. The 2 Buttons on the EVK2 could not be used with the DE910 Interface. 31.5. Content of the kit Please check out the contents of your interface kit;...
Page 141: Ce910 Family Interface
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 CE910 family Interface This board allows easily interfacing the CE910 modules with the EVK2 and testing their functionalities. No settings are needed. Figure 90: CE910 Interface Board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved...
Page 142: Stand-Alone Setup
2 female connectors (40 PTH pins each one: SO101, SO104), to connect the interface to the EVK2 mother board circuits (power supply lines, serial in/out lines, audio in/out lines); 1 USB connector (SO202) related to the CE910 USB 2.0 port.
Page 143: Antenna Connectors
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 32.3. Antenna connectors 32.3.1. CDMA Antenna connector A CDMA compatible antenna (Refer to the product’s HW user guide) must be connected to SO103. 32.4. Expansion Connectors 32.4.1. PL301/PL302 The connectors are carrying the following signals:...
Page 144: Pl303/Pl304
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 32.4.2. PL303/PL304 The connectors are carrying the following signals: PL303 Pin# Pin Name Description TX_AUX Auxiliary serial port (TX) RX_AUX Auxiliary serial port (RX) RESERVED RESERVED RESERVED GPIO_08 GPIO_09 GPIO_10 RESERVED PL304...
Page 145: On_Off & Unconditional Shudown Buttons
The 2 Buttons present on the Interface should be used to control the Power ON and UNCONDITIONAL SHUTDOWN lines of the module. The 2 Buttons on the EVK2 could not be used with the CE910 Interface. 32.5. Content of the kit Please check out the contents of your interface kit;...
Page 146: Gl865 V3 Interface
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 GL865 V3 Interface This board allows easily interfacing the GL865-DUAL V3 modules with the EVK2 and testing their functionalities. No settings are needed. Figure 92: GL865 V3 Interface Board 33.1. Stand-alone setup The Jumper setting and the assembled components are ready permitting the standalone use.
Page 147: Interface Connectors
Telit extension boards, measurements equipment or other tools; 2 female connectors (40 PTH pins each one: SO101, SO104), to connect the interface to the EVK2 mother board circuits (power supply lines, serial in/out lines, audio in/out lines); 1 RF connectors for GSM Antenna (SO103)
Page 148: Antenna Connectors
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 33.3. Antenna connectors 33.3.1. GSM Antenna connector A GSM compatible antenna (Refer to the product’s HW user guide) antenna must be connected to SO103. 33.4. Expansion Connectors 33.4.1. PL101 The connector is carrying the following signals:...
Page 149: Pl107
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 33.4.3. PL107 The connector is providing the following signals: PL102 Pin# Pin Name Description EAR_HF+ Audio output path EAR+ Audio output path EAR_HF- Audio output path EAR- Audio output path MIC_HF+ Audio input path...
Page 150: Le920 Interface
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 LE920 Interface This board allows easily interfacing the LE920 module with the EVK2 and testing their functionalities. No settings are needed. Figure 94: LE920 Interface Board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved...
Page 151: Stand-Alone Setup
2 female connectors (40 PTH pins each one: SO101, SO104), to connect the interface to the EVK2 mother board circuits (power supply lines, serial in/out lines, audio in/out lines); 1 USB connector (SO202) related to the LE920 USB 2.0 port.
Page 152: Antenna Connectors
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 34.3. Antenna connectors 34.3.1. Main Antenna connector A LTE/HsPA/GSM/GPRS compatible antenna (Refer to the product’s HW user guide) antenna must be connected to SO105. 34.3.2. Diversity Antenna connector A LTE/HsPA diversity (secondary) compatible antenna (Refer to the product’s HW user guide) antenna must be connected to SO107.
Page 153 Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 RESERVED RESERVED TGPIO_04 RESERVED RESERVED RESERVED RESERVED TGPIO_01 RESERVED RESERVED RESERVED PL104 Pin# Pin Name Description TGPIO_05 TGPIO_07 TGPIO_08 TGPIO_09 TGPIO_10 TGPIO_03 RESERVED RESERVED RESERVED TGPIO_06 RESERVED RESERVED VAUX 1.8V VRTC ADC1...
Page 154: On_Off & Unconditional Shutdown, Reset Buttons
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 RESERVED RESERVED VBAT VBAT 34.4.2. ON_OFF & UNCONDITIONAL SHUTDOWN, RESET BUTTONS The 3 Buttons present on the Interface should be used to control the Power ON and UNCONDITIONAL SHUTDOWN, and RESET lines of the module.
Page 155: Gpio Ports
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 GPIO ports A certain number of GPIO ports (General Purpose Input/Output) are available on every Telit Module Interface Board, giving you the possibility to drive digital devices and report their own status.
Page 156: Gpio Location
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 35.1. GPIO location 35.1.1. GM862 Interface (Refer to schematic diagram 30276SE11150B) Figure 96: Position of GPIO ports on GM862 interface Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved...
Page 157 Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 Note on GM862-GPS version If you use this interface in conjunction with GM862-GPS version be careful that the following two pins of SO101 connector assume different functions, and precisely: Pin 2 = TX_GPS Pin 3 = RX_GPS Reproduction forbidden without Telit Communications S.p.A.
Page 158: Ge863-Gps Interface
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 35.1.2. GE863-GPS Interface (Refer to schematic diagram 30276SE11151A) Figure 97: Position of GPIO ports on GE863-GPS interface Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 158 of 243...
Page 159 Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 Note on p/n 3990250684 and p/n 3990250685 GE863 (Refer to schematic diagrams 30276SE11151A-C, 30276SE11151A-D) If you use these interfaces the following two pins of PL104 connector assume different functions, and precisely: Pin 20 = ADC_IN2 Pin 21 = ADC_IN3 Pin 26 = N.C...
Page 160: Ge863 Interfaces (P/N 3990250684 -3990250685-3990250703)
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 35.1.3. GE863 Interfaces (p/n 3990250684 -3990250685-3990250703) Refer to schematic diagrams 3\0276SE11151A-C; 30276SE11151A-D; 30276SE11151A- Figure 98: Position of GPIO ports on GE863 interfaces Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved...
Page 161: Ge864 Interface (P/N 3990250672)
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 35.1.4. GE864 Interface (p/n 3990250672) (Refer to schematic diagram 30276SE1152B) Figure 99: Position of GPIO ports on GE864 interface Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 161 of 243...
Page 162: Ge864-Gps Interface (P/N 3990250822)
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 35.1.5. GE864-GPS Interface (p/n 3990250822) (Refer to schematic diagram 30373SE11439b) Figure 100: Position of GPIO ports on GE864-GPS interface Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 162 of 243...
Page 163: Ge865/Se867-Agps Interface (P/N 3990250814)
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 35.1.6. GE865/SE867-AGPS Interface (p/n 3990250814) (Refer to schematic diagram 30311SE11433) Figure 101: Position of GPIO ports on GE865/SE867-AGPS interface Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 163 of 243...
Page 164: Gc864 Interface
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 35.1.7. GC864 Interface (Refer to schematic diagram 30276SE111203B) Figure 102. Position of GPIO ports on GC864 interface Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 164 of 243...
Page 165: Gc864-C2 Interface (P/N 3990250683)
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 35.1.8. GC864-C2 Interface (p/n 3990250683) (Refer to schematic diagram 30276SE11231X) Figure 103. Position of GPIO ports on GC864-C2 interface Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 165 of 243...
Page 166: Uc864 Interface
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 35.1.9. UC864 Interface J106 J105 PL101 PL102 J107 J108 ON/OFF UC864 CALL CC864 RESET GC864 SW101 USB_B J103 29 30 29 30 SUB MAIN J102 CON114 USB_A CON115 STAT LED CON111 CON107...
Page 167: He910 Interface
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 35.1.10. HE910 Interface Figure 105: Position of GPIO on connectors of HE910 interface Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 167 of 243...
Page 168 Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 The connectors are carrying the following signals: Pin Name Pin/Connector GPIO_01 Pin 1 (PL302) GPIO_02 Pin 2 (PL302) GPIO_03 Pin 3 (PL302) GPIO_04 Pin 4 (PL302) GPIO_05 Pin 6 (PL102) GPIO_06 Pin 5 (PL302)
Page 169: Ge910 Interface
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 35.1.11. GE910 Interface Figure 106: Position of GPIO on connectors of GE910 interface Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 169 of 243...
Page 170 Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 The connectors are carrying the following signals: Pin Name Pin/Connector GPIO_01 Pin 1 (PL302) GPIO_02 Pin 2 (PL302) GPIO_03 Pin 3 (PL302) GPIO_04 Pin 4 (PL302) GPIO_05 Pin 6 (PL102) GPIO_06 Pin 5 (PL302)
Page 171: De910 Interface
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 35.1.12. DE910 Interface Figure 107: Position of GPIO on connectors of DE910 interface Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 171 of 243...
Page 172 Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 The connectors are carrying the following signals: Pin Name Pin/Connector GPIO_01 Pin 1 (PL302) GPIO_02 Pin 2 (PL302) GPIO_03 Pin 3 (PL302) GPIO_04 Pin 4 (PL302) GPIO_05 Pin 6 (PL102) GPIO_06 Pin 5 (PL302)
Page 173: Ce910 Interface
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 35.1.13. CE910 Interface Figure 108: Position of GPIO on connectors of CE910 interface Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 173 of 243...
Page 174 Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 The connectors are carrying the following signals: Pin Name Pin/Connector GPIO_01 Pin 1 (PL302) GPIO_02 Pin 2 (PL302) GPIO_03 Pin 3 (PL302) GPIO_04 Pin 4 (PL302) GPIO_05 Pin 6 (PL102) GPIO_06 Pin 5 (PL302)
Page 175: Gl865 V3 Interface
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 35.1.14. GL865 V3 Interface Figure 109: Position of GPIO on connectors of GL865 V3 interface Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 175 of 243...
Page 176 Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 The connectors are carrying the following signals: Pin Name Pin/Connector GPIO_01 Pin 6 (PL102) / Pin 4 (PL106) GPIO_02 Pin 23 (PL102) / Pin 2 (PL106) GPIO_03 Pin 8 (PL102) / Pin 6 (PL106)
Page 177: Schematics
1vv0300704 Rev.17 – 2013/05/30 SCHEMATICS In the following paragraphs the user can find the schematics related to all EVK2 boards, therefore to the Mother Board, to the Interface Boards and to the Extension Boards. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved...
Page 178: Evk2 Mother Board
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 36.1. EVK2 Mother Board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 178 of 243...
Page 183: Gm862 Interface Board
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 36.2. GM862 Interface Board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 183 of 243...
Page 184: Ge863 Interface Board
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 36.3. GE863 Interface Board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 184 of 243...
Page 185 Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 NOTE: This sheet is related only to GPS version. Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 185 of 243...
Page 186: Ge864 Interface Board
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 36.4. GE864 Interface board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 186 of 243...
Page 187: Ge864 Interface Board – Automotive
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 36.5. GE864 Interface board – Automotive Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 187 of 243...
Page 188: Ge864 Interface Board – V2
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 36.6. GE864 Interface board – V2 Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 188 of 243...
Page 189: Ge864-Gps Interface Board
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 36.7. GE864-GPS Interface board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 189 of 243...
Page 191: Ge865/Se867-Agps Interface Board
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 36.8. GE865/SE867-AGPS Interface board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 191 of 243...
Page 193: Ge865 Interface Board
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 36.9. GE865 Interface board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 193 of 243...
Page 194: Gl865 Interface Board
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 36.10. GL865 Interface board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 194 of 243...
Page 195: Gc864 Interface Board
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 36.11. GC864 Interface board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 195 of 243...
Page 196: Gc864-C2 Interface Board
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 36.12. GC864-C2 Interface board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 196 of 243...
Page 197: Uc864 Interface Board
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 36.13. UC864 Interface board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 197 of 243...
Page 199: He910/Ue910 Interface Board
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 36.14. HE910/UE910 Interface board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 199 of 243...
Page 203: Ge910 Interface Board
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 36.15. GE910 Interface board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 203 of 243...
Page 207: Ge910-Gnss Interface Board
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 36.16. GE910-GNSS Interface board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 207 of 243...
Page 211: Ge910-Quad V3 Interface Board
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 36.17. GE910-QUAD V3 Interface board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 211 of 243...
Page 215: Ge865 – Jf2 Interface Board
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 36.18. GE865 – JF2 Interface board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 215 of 243...
Page 218: Gl865 – Sl869/Jn3 Interface Board
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 36.1. GL865 – SL869/JN3 Interface board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 218 of 243...
Page 221: De910 Interface Board
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 36.2. DE910 Interface board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 221 of 243...
Page 225: Ce910 Interface Board
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 36.3. CE910 Interface board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 225 of 243...
Page 229: Gl865 V3 Interface Board
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 36.4. GL865 V3 Interface board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 229 of 243...
Page 230: Le920 Interface Board
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 36.5. LE920 Interface board Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 230 of 243...
Page 235: Service And Firmware Update
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 Service and firmware update You can update the Telit Module firmware through the serial cables (RS232 or USB 1.1) used for the communication with a PC. The firmware update can be done with a specific software tool provided by Telit that runs on windows based PCs.
Page 236: Safety Recommendations
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 SAFETY RECOMMENDATIONS READ CAREFULLY Be sure the use of this product is allowed in the country and in the environment required. The use of this product may be dangerous and has to be avoided in the following areas:...
Page 237: Disposal Of This Product In The European Union
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 The text of the Directive 99/05 regarding telecommunication equipments is available, while the applicable Directives (Low Voltage and EMC) are available at: http://europa.eu.int/comm/enterprise/electr_equipment/index_en.htm 38.1. Disposal of this product in the European Union According to the directives 2002/95/CE, 2002/96/CE and 2003/108/CE, which have been transposed in Italian Legislative Decree of July 25, 2005, n.
Page 238 Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 Reference Directives and Laws 2002/95/EC Directive of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS)
Page 239: Rohs Certifications
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 RoHS Certifications Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 239 of 243...
Page 240: Disposal Of Old Electrical & Electronic Equipment (Weee Mark)
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 Disposal of old Electrical & Electronic Equipment (WEEE Mark) This symbol, applied on our products and/or on its packaging, indicates that this product should not be treated as household waste when you wish to dispose of it. Instead, it should be handed over to an applicable collection point for the recycling of electrical and electronic equipment.
Page 241: Document History
Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 Document History Revision Date Changes Rev 0 05/01/2006 First issue Rev 1 23/01/2006 Added PCB weight and dimensions pag.9 Added default setup pag.8 Correct mA/h with mAh pag.16 Unified the scripting “impedance coil” pag.19 and pag.20 Insert the power supply pag.7...
Page 242 Erased all Dual Camera paragraph Figures and table updated Paragraph 15.3 16.2 17.3 18.3 19.3 inserted 24.1 EVK2 SYS p/n 3990150463: added RoHS certification 24.9 GE864-QUAD Interface p/n 3990250688: added RoHS certification 24.11 GE864-QUAD-C2 Interface p/n 3990250683: added RoHS certification Reproduction forbidden without Telit Communications S.p.A.
Page 243 Telit EVK2 User Guide 1vv0300704 Rev.17 – 2013/05/30 Rev.7 22/01/2008 Pag. 2 Product Table updated with UC864-E and GE863-SIM Pag.7 Disclaimer Date modified Pag.13 Inserted UC864 Interface dimensions Pag.36 Inserted refer to GE863-SIM Pag.38 Table 10 Inserted UC864 and GE863-SIM Interface Code Pag.38 Order Code Table updated...

Telit Wireless Solutions EVK2 User Manual

1 Introduction

2 Description

3 Startup Procedure

4 Insertion of the Interface Boards

5 Power Supply Setting

6 Serial Interface

7 Audio Section

8 AF Amplifiers Setting

9 Audio Outputs

10 Audio Accessories

11 Indication and Services

12 Connectors Pinout

13 Module Interface Boards

14 GM862 Interface

15 GE863 Interface

16 GE864 Interface

17 GE864-GPS Interface

18 GE865 - SE867 AGPS Interface

19 GE865 - JF2 Interface

20 GL865 - SL869/JN3 Interface

22 GC864-C2 Family Interface

25 UC864 Family Interface

26 HE910 Family Interface

27 UE910 Family Interface

24 GL865 Interface

31 DE910 Family Interface

32 CE910 Family Interface

34 LE920 Interface

35 Gpio Ports

36 Schematics

37 Service and Firmware Update

38 Safety Recommendations

39 Rohs Certifications

40 Disposal of Old Electrical & Electronic Equipment (WEEE Mark)

41 Document History

Quick Links

Need help?

Questions and answers

Related Manuals for Telit Wireless Solutions EVK2

Summary of Contents for Telit Wireless Solutions EVK2