Remaining Hazards; Machine Specifications; Technical Data; Noise Emission - Jet HVBS-712K Operating Instructions Manual

No changes to the machine may be
made.
Daily inspect the function and
existence of the safety appliances
before you start the machine.
Do not attempt operation in this case,
protect the machine by unplugging
the mains cord.
Remove all loose clothing and
confine long hair.
Before operating the machine,
remove tie, rings, watches, other
jewellery, and roll up sleeves above
the elbows.
Wear safety shoes; never wear
leisure shoes or sandals.
Always wear the approved working
outfit
Do not wear gloves while operating
this machine.
For the safe handling of saw blades
wear work gloves.
Insure that the workpiece does not
roll when cutting round pieces.
Use suitable table extensions and
supporting aids for difficult to handle
workpieces.
Always adjust the blade guide close
to the workpiece.
Remove cut and jammed workpieces
only when motor is turned off and the
machine is at a complete standstill.
Install the machine so that there is
sufficient space for safe operation
and workpiece handling.
Keep work area well lighted.
The machine is designed to operate
in closed rooms and must be placed
stable on firm and levelled ground.
Make sure that the power cord does
not impede work and cause people to
trip.
Keep the floor around the machine
clean and free of scrap material, oil
and grease.
Stay alert!
Give your work undivided attention.
Use common sense.
Do not operate the machine when you
are tired.
Do not operate the machine under the
influence of drugs, alcohol or any
medication. Be aware that medication
can change your behaviour.
Keep children and visitors a safe
distance from the work area.
Never reach into the machine while it
is operating or running down.
Never leave a running machine
unattended.
Before you leave the workplace
switch off the machine.
Do not operate the electric tool near
inflammable liquids or gases.
Observe the fire fighting and fire alert
options, for example the fire
extinguisher operation and place.
Do not use the machine in a dump
environment and do not expose it to
rain.
Specifications regarding the
maximum or minimum size of the
workpiece must be observed.
Do not remove chips and workpiece
parts until the machine is at a
complete standstill.
Never operate with the guards not in
place – serious risk of injury!
Connection and repair work on the
electrical installation may be carried
out by a qualified electrician only.
Have a damaged or worn cord
replaced immediately.
Make all machine adjustments or
maintenance with the machine
unplugged from the power source.
Remove defective saw blades
immediately.

3.3 Remaining hazards

When using the machine according to
regulations some remaining hazards
may still exist
The moving saw blade in the work
area can cause injury.
Broken saw blades can cause
injuries.
Thrown cutting chips and noise can
be health hazards.
Be sure to wear personal protection
gear such as safety goggles and ear
protection.
The use of incorrect mains supply or
a damaged power cord can lead to
injuries caused by electricity.

4. Machine specifications

4.1 Technical data

4
Cutting capacity 90°
Cutting capacity 45°
•180x110 mm
Vice adjustment
Vice bed above floor
Wheel diameter
Sawblade size 20x0,9x2362 mm
Cutting speeds 20/ 32/ 45/ 72 m/min
Coolant tank
Coolant pump
Overall LxWxH 1250x520x960 mm
Weight
Mains 230V ~1/N/PE 50Hz
Output power 0,56 kW (0,75 HP)-S1
Reference current
Extension cord (H07RN-F): 3x1,5mm²
Installation fuse protection
Mains 400V ~3/PE 50Hz
Output power 0,75 kW (1 HP)-S1
Reference current
Extension cord (H07RN-F): 5x1,5mm²
Installation fuse protection

4.2 Noise emission

Acoustic pressure level (EN 11202):
Idling
Operating
The specified values are emission
levels and are not necessarily to be
seen as safe operating levels.
As workplace conditions vary, this
information is intended to allow the
user to make a better estimation of
the hazards and risks involved only.

4.3 Contents of delivery

Machine stand with wheels
20mm bimetal sawblade
Adjustable material stop
Belt drive and cover
Hydraulic cylinder
Coolant facility
Assembly kit
Operating manual
Spare parts list

5. Transport and start up

5.1 Transport and installation

Lift machine off the pallet to the
desired location.
Use lifting straps and place them as
shown in Fig 1.
Ø180 mm
•180 mm
65x300 mm
Ø110 mm
0° - 45°
585 mm
300 mm
10 litre
0,13 HP
137 kg
5 A
10 A
1.5 A
10 A
74,1 dB (A)
85 dB (A)