Related Manuals for Fires of Tradition Solano Jurastone 4012
Summary of Contents for Fires of Tradition Solano Jurastone 4012
- Page 1 Install Instructions for Solano Jurastone #4012 Mantel Please read this manual before installing the suite. This manual should remain with the homeowner.
- Page 2 Fires of Tradition assumes no responsibility for the colour and texture varia- tions of Jurastone mantels. There will be slight variations in colour and texture from time to time. Fires of Tradition assumes no responsibility for the care and cleaning of Jurastone mantel.
- Page 3 #4012 IRES OF RADITION NSTALL NSTRUCTIONS FOR OLANO ANTEL Before you begin to install the Valor gas fireplace, take the time to completely read this manual, and to familiarize yourself with all of the components that are required to complete the installation. This is critical to make sure that you have a complete understanding of the inter relationship of these components.
- Page 4 #4012 IRES OF RADITION NSTALL NSTRUCTIONS FOR OLANO ANTEL The mantel consists of- • 1 pc left leg • 1 pc right leg • 1 pc shelf • 1 pc mid hearth • 1 pc hearth [optional] Note that the mantel kit also contains the brackets, a bag of thinset adhesive, a pair of gloves and a hardware blister pack.
- Page 5 #4012 IRES OF RADITION NSTALL NSTRUCTIONS FOR OLANO ANTEL The fireplace must be installed off the floor to account for the height of the hearth and the riser (the riser is included with the four piece slip system). The total height that the unit must sit at is 7 ¾”...
- Page 6 #4012 IRES OF RADITION NSTALL NSTRUCTIONS FOR OLANO ANTEL The wooden 2x3 backing for the steel bracket must be installed according to the dimensions shown. Insure that this framing is centered on the fireplace and the wall, as this will dictate the final position of the mantel.
- Page 7 #4012 IRES OF RADITION NSTALL NSTRUCTIONS FOR OLANO ANTEL The front plate of the Fenderfire can be Step #6 adjusted inwards outwards loosening the 4 screws on the inside of the frame. Insure that this plate lies flush with the notched face of the base of the 4pc frame (this step may need to be repeated after the install is complete).
- Page 8 #4012 IRES OF RADITION NSTALL NSTRUCTIONS FOR OLANO ANTEL Important!! When applying the mantel pcs into position that have cement on them, be very careful that you set the pc down into its final position. Avoid moving the pc around, and spreading the cement beyond it’s intended final resting position. If this does happen, wipe it off immediately with a clean, damp cloth.
- Page 9 #4012 IRES OF RADITION NSTALL NSTRUCTIONS FOR OLANO ANTEL Now that the inner slip system is in Step #11 place the leg can now be cemented in place. Note; One person will need to steady the vertical and horizontal of the four piece slip system while the leg is removed until the leg is replaced again.
- Page 10 #4012 IRES OF RADITION NSTALL NSTRUCTIONS FOR OLANO ANTEL Don’t forget to apply a small amount of Step #14 cement in the holes when the shims are removed. Carefully wipe excess cement off mantel along the joints with a wet cloth. Any marks that have occured on the surface of the mantel can be cleaned off very easily using the white eraser provided.
- Page 11 #4012 IRES OF RADITION NSTALL NSTRUCTIONS FOR OLANO ANTEL Installing the Solano mantel around the Horizon 534 with the Clearview front and the 3 piece slip kit The fireplace must be installed off the floor to account for the height of the two pc hearth.
- Page 12 #4012 IRES OF RADITION NSTALL NSTRUCTIONS FOR OLANO ANTEL The wooden 2x3 backing for the steel bracket must be installed according to the dimensions shown. Insure that this framing is centered on the fireplace and the wall, as this will dictate the final position of the mantel.
- Page 13 #4012 IRES OF RADITION NSTALL NSTRUCTIONS FOR OLANO ANTEL Carefully set each leg into position on the hearth, positioning the inside of the leg up against the “stop” created by the cutout in the mid hearth. There is a light line marked on the hearth indicating the approximate position of the foot of each leg.
- Page 14 #4012 IRES OF RADITION NSTALL NSTRUCTIONS FOR OLANO ANTEL Note: the legs aren’t secured yet, so Step #9 there is a very high risk for one to fall over and be damaged. Exercise extreme caution while working around them. Carefully lower the vertical slips into place.
- Page 15 #4012 IRES OF RADITION NSTALL NSTRUCTIONS FOR OLANO ANTEL By carefully and gently tilting the leg to the side, you can now set the arched Step #11 upper slip onto position onto the side slips already in position. This step is a two person job.
- Page 16 #4012 IRES OF RADITION NSTALL NSTRUCTIONS FOR OLANO ANTEL Check the fit of the shelf onto the top of the beam and bracket, then remove. Adjust bracket if necessary. Apply a thin Step #14 bead of cement along the top edge of the legs, against the back edges of the shelf, and along the inside edge where the shelf comes into contact with the hori-...
- Page 17 Dust and air born dirt will settle on any mantel surface. This can easily be removed by a vacuum with a soft bristle head. Be careful to not scratch the surface in the process. Distributed in Canada and U.S.A. by; Fires of Tradition 137 Nelson St Brantford Ontario Canada N3S4B5...