Related Manuals for Fires of Tradition Torrance Jurastone 4004
Summary of Contents for Fires of Tradition Torrance Jurastone 4004
- Page 1 Install Instructions for Torrance Jurastone #4004 Mantel Please read this manual before installing the suite. This manual should remain with the homeowner. Updated 12/03/12...
- Page 2 Fires of Tradition assumes no responsibility for the colour and texture variations of Jurastone mantels. There will be slight variations in colour and texture from time to time. Fires of Tradition assumes no responsibility for the care and cleaning of Jurastone mantel.
- Page 3 #4004 IRES OF RADITION NSTALL NSTRUCTIONS FOR URASTONE ORRANCE Before you begin to install the Valor gas fireplace, take the time to completely read this manual, and to familiarize yourself with all of the components that are required to complete the installation. This is critical to make sure that you have a complete understanding of the inter relationship of these components.
- Page 4 #4004 IRES OF RADITION NSTALL NSTRUCTIONS FOR URASTONE ORRANCE The mantel consists of- • 1 pc left leg • 1 pc right leg • 1 pc beam • 1 pc shelf • 1 pc hearth [optional] Note that the mantel kit also contains the brackets, a bag of thinset adhesive, a pair of gloves and a hardware blister pack.
- Page 5 #4004 IRES OF RADITION NSTALL NSTRUCTIONS FOR URASTONE ORRANCE Installing the Torrance with the 534, 4 pc slip kit & Fenderfire Front fireplace must Step #1 installed floor account for the height of the hearth and the riser (the riser is included with the four piece slip system).
- Page 6 #4004 IRES OF RADITION NSTALL NSTRUCTIONS FOR URASTONE ORRANCE It is the combination of the wooden Step #3 2x3’s and the steel brackets that securely hold the mantel to the wall. This wooden 2x3 backing for the steel brackets must be installed according to the dimensions shown.
- Page 7 #4004 IRES OF RADITION NSTALL NSTRUCTIONS FOR URASTONE ORRANCE It is very important that sufficient Step #6 screws are installed in the brackets and in the wood to support the whole man- tel. Failure to insure that these brackets are firmly secured to the wall risks that the mantel could fall off the wall, result- ing in serious injury.
- Page 8 #4004 IRES OF RADITION NSTALL NSTRUCTIONS FOR URASTONE ORRANCE Important!! When setting the mantel pieces into position that have cement on them, be very careful that you set the pc down into its final position. Avoid moving the pc around, and spreading the cement beyond it’s intended final resting position. If this does happen, wipe it off immediately with a clean, damp cloth.
- Page 9 #4004 IRES OF RADITION NSTALL NSTRUCTIONS FOR URASTONE ORRANCE This image is looking down inside the leg. Take one of the wooden shims sup- plied in the blister pack, and carefully insert it between the block on the inside top of the leg and the bracket. This will help hold the leg against the wall.
- Page 10 #4004 IRES OF RADITION NSTALL NSTRUCTIONS FOR URASTONE ORRANCE Check the fit of the beam against the top of the legs, and install another wooden shim between the bracket and the block on each side. This will hold the beam against the wall in a secure man- ner.
- Page 11 #4004 IRES OF RADITION NSTALL NSTRUCTIONS FOR URASTONE ORRANCE Check the fit of the shelf onto the top of the beam and bracket, then remove. Adjust bracket if necessary. Apply a thin bead of cement along the top edge of the beam, and against the back edges of the shelf.
- Page 12 #4004 IRES OF RADITION NSTALL NSTRUCTIONS FOR URASTONE ORRANCE Installing the Torrance with the 534, 3 pc slip kit & Clearview Front The fireplace must be installed off the floor to account for the height of the Step #1 hearth riser (the riser...
- Page 13 #4004 IRES OF RADITION NSTALL NSTRUCTIONS FOR URASTONE ORRANCE It is the combination of the wooden Step #3 2x3’s and the steel brackets that securely hold the mantel to the wall. This wooden 2x3 backing for the steel brackets must be installed according to the dimensions shown.
- Page 14 #4004 IRES OF RADITION NSTALL NSTRUCTIONS FOR URASTONE ORRANCE It is very important that sufficient screws are installed in the brackets and in the wood to support the whole mantel. Failure to insure that these brackets are firmly secured to the wall risks that the mantel could fall off the wall, resulting in serious injury.
- Page 15 #4004 IRES OF RADITION NSTALL NSTRUCTIONS FOR URASTONE ORRANCE Important!! When setting the mantel pieces into position that have cement on them, be very careful that you set the pc down into its final position. Avoid moving the pc around, and spreading the cement beyond it’s intended final resting position. If this does happen, wipe it off immediately with a clean, damp cloth.
- Page 16 #4004 IRES OF RADITION NSTALL NSTRUCTIONS FOR URASTONE ORRANCE Carefully set one of the side slips into Step #11 position, by sliding it behind the inner edge of the leg, and into the slot in the bottom riser. Note the edges that it comes in contact with.
- Page 17 #4004 IRES OF RADITION NSTALL NSTRUCTIONS FOR URASTONE ORRANCE Apply a bead of cement along top edge of the left and right slip and the inside Step #14 edge of the beam, where the fourth piece of the slip kit comes in contact with the beam.
- Page 18 Dust and air born dirt will settle on any mantel surface. This can easily be removed by a vacuum with a soft bristle head. Be careful to not scratch the surface in the process. Distributed in Canada and U.S.A. by; Fires of Tradition 17 Oxbow Lane Brantford Ontario Canada N3T-5L6...