Yamaha WK83840 Owner's Manual page 59

Message
Connection to Master Communication with the master DME device has been
DME is Lost interrupted.
Connection to Slave Communication with the slave DME device has been
SME is Lost interrupted.
Download Success The program has been successfully updated.
Downloading Program update in progress. Do NOT turn power off
Do not turn off while the unit displays this message.
DSP Power Shortage Audio is not input or output and is muted due to
insufficient DSP resources.
Duplicate IP Adr. Duplicate IP addresses.
The device group configuration set via DME Designer
Err: Wrong Device
Group Settings does not match the actual configuration.
Executing Direct setup from the User Defined Buttons in progress.
File Opening A file operation is in progress during which the computer
Do not turn off manipulates scene data. Do NOT turn power off while the
unit displays this message.
Illegal MAC Adr. An illegal MAC address has been encountered.
Invalid IP Adr. The network IP address is not appropriate.
Network Busy There is too much network traffic. Communication is not
possible.
Network Error One of the following errors has occurred on the network:
• A cable has been unplugged.
• The power to a hub or router has been shut off.
• A cable is in an inappropriate state (e.g. a heavy object
has been placed on the cable, etc.). Static electricity
can also cause errors.
Network Setup Preparing network connection.
No Current Scene There is no data in the current scene.
No MAC Adr. MAC address not specified.
Panel Locked Panel operation not allowed.
Panel Unlocked Panel lock has been disengaged. Panel operation is now
possible.
Recovering A program update attempt has failed, and the previous
Do not turn off program is currently being restored.
Saving HA Info Head amplifier info save in progress.
Do not turn off (Do not turn power off.)
Saving Setup Info Info set up via the Utility display (other than head
Do not turn off amplifier info) is being saved.
(Do not turn power off.)
Scene Recalling Scene recall in progress. Do NOT turn power off while
Do not turn off the unit displays this message.
Scene Storing Scene store in progress. Do NOT turn power off while the
Do not turn off unit displays this message.
Currently searching for the master DME unit.
Searching for Master
DME Unit...
Searching for Slave Currently searching for the slave DME unit.
DME Unit...
SLOT1 Sync Err The DME64N/24N clock is not synchronized with the
clock of the card installed in I/O slot 1.
SLOT2 Sync Err The DME64N clock is not synchronized with the clock of
the card installed in I/O slot 2.
SLOT3 Sync Err The DME64N clock is not synchronized with the clock of
the card installed in I/O slot 3.
Meaning Action
Check that all cables are properly connected, and than
hubs, routers, and related devices are functioning
properly.
Check that all cables are properly connected, and than
hubs, routers, and related devices are functioning
properly.
—
—
This error sometimes occurs if you try to operate a
configuration at 96 kHz that has been created with a
word clock of 48 kHz. To operate a configuration at any
word clock setting, use DME Designer to create a
configuration with the word clock set to 96 kHz.
Change the IP addresses so that there are no duplicates.
Use DME Designer to go off-line, create a configuration
that correctly matches the actual configuration, and then
go back on-line to synchronize the configuration.
—
—
This could be due to a hardware malfunction. Refer this
problem to a contact a Yamaha dealer.
Set an appropriate network IP address.
Check the devices connected to the network. If there are
too many devices connected, reduce the number of
devices.
Locate and eliminate the cause of the error.
—
Send appropriate scene data from a computer running
the DME Designer application.
This could be due to a hardware malfunction. Refer this
problem to a Yamaha dealer.
Press the [CANCEL] button for longer than 2 seconds to
disengage panel lock and allow panel operation.
—
Do NOT turn power off while the unit is displaying this
message. If the update attempt repeatedly fails, there
may be a hardware malfunction. Refer this problem to a
Yamaha dealer.
—
—
—
—
—
—
Make sure that the DME64N/24N and the card or
external source supplying the word clock are set to use
the same word clock.
Make sure that the DME64N and the card or external
source supplying the word clock are set to use the same
word clock.
Make sure that the DME64N and the card or external
source supplying the word clock are set to use the same
word clock.
DME64N/DME24N Owner's Manual
Error Messages
59