Error Messages - Yamaha WK83840 Owner's Manual

Yamaha digital mixing engine owner's manual
Table of Contents

Advertisement

Error Messages

Error Messages
Message
Error messages
Cannot Select
Component Corrupt
Update Firmware!
Critical Battery
Int.Data Corrupt
Invalid Password
Log Buffer Full
Low Battery
No Battery
Param Access Err
Param Set Err
ResumeData Corrupt
Recall a Scene!
Resume Data Lost!
Recall a Scene!
Saving Failed
Slots Overloaded
Store Disable
Storing Failed
Used by ExDevice
Used by HA Ctrl
Used by MIDI
Status messages
Cable Disconnect
Cannot be assigned
Cannot Store
CAS. In Sync Err
CAS. Out Sync Err
58
DME64N/DME24N Owner's Manual
Meaning
No selectable items are available in the scene or
monitoring point list display.
The component data is corrupt or can't be found.
The internal battery is almost discharged. Your data may
be lost.
Data inside the internal flash memory has been erased.
An invalid password has been entered.
Saving is not possible, since the Event Log saving area is
full.
The backup battery voltage is low.
The internal battery is completely discharged or not
installed.
The current setting cannot be displayed because the
parameter you attempted to operate does not exist. It is
possible that the component is not operating normally.
The current setting cannot be changed because the
parameter you attempted to operate does not exist. It is
possible that the component is not operating normally.
The data has been partially corrupted due to power
shutdown while writing to the internal memory. The
current settings have been lost.
Current setting has been lost.
A save operation has failed.
The current being used by all cards installed in I/O slots
exceeds the rated limit.
The scene store parameter is set to "Disable."
Either the flash memory for storing data is full, or the file
system has been damaged.
The connector selected by the Internal HA Ctrl
parameter or the MIDI Port parameter is already being
controlled by an external device (such as the PM5D).
The connector selected by the MIDI Port parameter is
already selected for internal head amp control from an
external device.
This cannot be set, since the connector selected by the
Internal HA Ctrl parameter is already used by the MIDI
function.
No network cable connected.
No parameter assigned.
The scene data is protected.
The DME64N/24N clock is not in sync with the clock
signal being received at the [CASCADE IN] connector.
The DME64N/24N clock is not in sync with the clock
signal being received at the [CASCADE OUT] connector.
Action
Make the appropriate settings via the DME Designer
application.
Restart after updating the component using DME
Designer. If the error indicators are still indicating the
error, execute the "Delete All Data" initialization. If the
problem persists, contact a Yamaha dealer.
If you turn off power to the unit, the current settings may
be lost and reset to the default values. Stop operating the
unit, and contact a Yamaha dealer for battery
replacement.
Execute the "Delete All Data" initialization. If the problem
persists, contact a Yamaha dealer.
Enter the correct password. If you have lost or forgotten
your password, contact a Yamaha dealer.
Use DME Designer to delete the log.
This does not affect the operation of the unit. However, if
you continue using the unit, the settings may be lost and
reset to the default values. Contact a Yamaha dealer for
battery replacement at your earliest convenience.
If you turn off the power to the unit, the current settings
will be lost and reset to the default values. Stop operating
the unit, and contact a Yamaha dealer for battery
replacement.
Save the current settings using DME Designer, execute
the initialization (Delete All Data). If the problem persists,
contact a Yamaha dealer.
Save the current settings using DME Designer, execute
the initialization (Delete All Data). If the problem persists,
contact a Yamaha dealer.
Recall the scene again. If the problem persists, contact a
Yamaha dealer.
Recall the scene again.
If the problem persists, contact a Yamaha dealer.
Stop using the device immediately and contact a
Yamaha dealer.
Make sure that the total current consumption of the cards
used does not exceed the limit.
Set the scene store parameter to "Enable" via the Utility
display "Lock" page.
Reduce the number of unused scenes. Alternatively,
delete the files saved via the File Storage function. If
deleting these items does not solve the problem, execute
the Delete All Data initialization. If the problem persists,
contact a Yamaha dealer.
Stop control from the external device. If it is being
controlled from the PM5D, turn off the CONNECT button
in the PM5D's DME CONTROL screen.
Set the Internal HA Ctrl parameter to something other
than the connector you want to select for the MIDI Port
parameter.
Set the MIDI Port parameter to something other than the
connector you selected for Internal HA Ctrl.
Make sure that a network cable is properly connected,
and that all network devices are functioning normally.
Set the protect parameter to "OFF" via the DME Designer
application.
Make sure that the DME64N/24N and the card or
external source supplying the word clock are set to use
the same word clock.
Make sure that the DME64N/24N and the card or
external source supplying the word clock are set to use
the same word clock.

Advertisement

Table of Contents
loading

This manual is also suitable for:

Dme64nDme24n

Table of Contents