Yamaha CP5 Reference Manual page 34

Yamaha electronic keyboard user manual
Hide thumbs Also See for CP5:
Table of Contents

Advertisement

Setting Controllers (Pages 3 to 5)
Press the [COMMON] button
Edit Sequence
[PAGE
R
On-screen name
Page
(and full name)
Pages
Source
3 to 5
3
CP5:
L1Dest (LEFT1 Destination)
L2Dest (LEFT2 Destination)
CP50:
LDest (LEFT Destination)
4
CP5:
R1Dest (RIGHT1 Destination)
R2Dest (RIGHT2 Destination)
CP50:
RDest (RIGHT Destination)
5
Mode (Switch Mode)
34
CP5/CP50 Reference Manual
Navigate to Page 3, 4, or 5 using the [
] buttons
Turn Knobs 1 to 3
This parameter is used to select the controller to be edited.
Setting values:
CP5 Performances:
PB (Pitch Bend wheel), FC1 (Foot Controller 1), FC2 (Foot Controller 2),
FS (assignable foot switch)
CP50 Performances:
PB (Pitch Bend wheel), FC (Foot Controller), FS (assignable foot switch)
FC1 or FC2 (CP5) / FC (CP50)
Foot controller(s) connected to the FOOT CONTROLLER jack(s)
FS
Foot switch connected to the ASSIGNABLE jack
These parameters are used to assign the controllers selected using
Source with a function for the corresponding part.
Setting values: As follows.
Source
PB (Pitch Bend)
FC1 or FC2 (CP5 Foot Control-
ler 1 or 2) / FC (CP50 Foot
Controller)
FS (assignable foot switch)
NOTE
If "modFx" is selected as a destination with Source set to "PB",
"FC1", "FC2", or "FC", you can then use the corresponding
controller to adjust one of the parameters from the Modulation
Effect block up or down with respect to the current setting. For
details on the actual parameter that will be assigned, see the
Modulation Effect block's parameter list in the Data List pdf
document. Specifically, the parameter marked
will be assigned to the controller.
NOTE
If Source is set to "FS", the function assigned as the destination can
be turned on and off by pressing the controller in question. If the
destination is specified as "vibrato", "modFx", or "pwrAmp",
pressing the controller will have the same effect as pressing the
[PRE-AMP], [MOD-FX], or [PWR-AMP] button. For details on how
this will affect the sound, refer to the Quick Guide section from the
Owner's Manual booklet.
This parameter is available only when Source has been set to "FS". It is
used to specify whether the controller in question will operate as a
latch-type or momentary-type switch. Latch-type switches remain on or
off after being operated, while momentary-type switches remain on only
while they are being operated.
Setting values: momentary or latch
PAGE] and
L
Description
Destination
off or modFx (modulation
effect)
off, volume, or modFx
off, vibrato, modFx, or
pwrAmp (CP5 only)
in the Control field
Internal Design of the CP5 & CP50
Reference
Left & Right Parts
R
[VOICE]
R
[PRE-AMP]
R
[MOD-FX]
R
[PWR-AMP] (CP5 only)
R
[LEFT1]/[LEFT2]/[RIGHT1]/
[RIGHT2] (CP5)
[LEFT]/[RIGHT] (CP50)
R
[COMMON]
Song Setting Area
R
[SONG SETTING]
[RECORD]
R
TRACK Part
R
[TRACK]
MIC INPUT Part
[MIC INPUT] (CP5 only)
R
Settings for All Parts
R
[REVERB]
Settings for All Performances
[MASTER COMPRESSOR]
R
R
[UTILITY]
R
[FILE]
Appendix

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Cp50

Table of Contents