Yamaha CP5 Reference Manual page 20

Yamaha electronic keyboard user manual
Hide thumbs Also See for CP5:
Table of Contents

Advertisement

On-screen name
(and full name)
D
Delay Time R>L
This parameter is used to set the time that elapses between input of sound via the right
channel and output via the left channel.
Density
Reverb effects: This parameter is used to set the reverb density.
Early Reflections: This parameter is used to set the density of early reflections.
Depth
This parameter is used to set the depth of the simulated room.
Detune
This parameter is used to set the degree to which pitches are detuned.
Device
This parameter is used to select one of a number of devices that distort the sound in dif-
ferent ways.
Diffusion
This parameter is used to adjust the spaciousness of the sound produced.
Direction
This parameter is used to set the direction of envelope-follower modulation.
Divide Freq High
This parameter is used to set the mid-to-high frequency when splitting the sound into
three bands.
Divide Freq Low
This parameter is used to set the low-to-mid frequency when splitting the sound into
three bands.
Drive
Distortion effects, Noisy, and Slice: This parameter is used to adjust the way in which the
sound distorts.
Miscellaneous effects: This parameter is used to set the degree to which the effect is
applied.
Drive Horn
This parameter is used to set the depth of modulation produced through rotation of the
high-frequency horn.
Drive Rotor
This parameter is used to set the depth of modulation produced through rotation of the
low-frequency rotor.
Dry Level
This parameter is used to adjust the volume of the dry sound (i.e., the unprocessed
sound).
Dry LPF Cutoff
This parameter is used to set the cutoff frequency for the low pass filter applied to the
Frequency
dry sound.
Dry Mix Level
This parameter is used to adjust the volume of the dry sound (i.e., the unprocessed
sound).
Dry Send to Noise
This parameter is used to adjust how much of the dry signal is sent to the noise effect.
Dry/Wet Balance
This parameter is used to set the balance between the dry sound and the wet sound
(i.e., the sound produced by the effect).
Dyna Level Offset
This parameter is used to set an offset for adjusting the level of the envelope follower's
output.
Dyna Threshold
This parameter is used to set the minimum level at which the envelope follower affects
Level
the input signal.
E
Edge
This parameter is used to specify a curve that determines how the sound is distorted.
Emphasis
This parameter is used to change the high-frequency characteristics of the processed
sound.
EQ Frequency
This parameter is used to set the EQ frequency.
EQ Gain
This parameter is used to set how much the EQ will boost or cut the sound at the corre-
sponding frequency.
EQ High Frequency
This parameter is used to set the center frequency of the high-frequency EQ band.
EQ High Gain
This parameter is used to set the amount by which the high-frequency EQ band is
boosted or cut.
EQ Low Frequency
This parameter is used to set the center frequency of the low-frequency EQ band.
EQ Low Gain
This parameter is used to set the amount by which the low-frequency EQ band is
boosted or cut.
EQ Mid Frequency
This parameter is used to set the center frequency of the mid-frequency EQ band.
EQ Mid Gain
This parameter is used to set the amount by which the mid-frequency EQ band is
boosted or cut.
20
CP5/CP50 Reference Manual
Description
Internal Design of the CP5 & CP50
Reference
Left & Right Parts
R
[VOICE]
R
[PRE-AMP]
R
[MOD-FX]
R
[PWR-AMP] (CP5 only)
R
[LEFT1]/[LEFT2]/[RIGHT1]/
[RIGHT2] (CP5)
[LEFT]/[RIGHT] (CP50)
R
[COMMON]
Song Setting Area
R
[SONG SETTING]
[RECORD]
R
TRACK Part
R
[TRACK]
MIC INPUT Part
[MIC INPUT] (CP5 only)
R
Settings for All Parts
R
[REVERB]
Settings for All Performances
[MASTER COMPRESSOR]
R
R
[UTILITY]
R
[FILE]
Appendix

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Cp50

Table of Contents